Vermont Casting 2466 Injector Orifice Size Matrix, Be sure to maintain 90 angle at left burner leg

Page 28

Dutchwest Direct Vent / Natural Vent Gas Heater

21.Replace burner. Slide the burner in at an angle with left side lower than the right side. Slide the left side onto the injectors, making sure the burner leg remains at a 90° angle to the base. Lower the right hand side down in to place. Make sure the burner is as far left as possible and the injector shoulders are inside the burner.

NOTE: It is very critical to keep the left burner leg, which holds the injectors, at a 90° angle to the base. (Fig. 57) This keeps the orifices aligned with the tubes inside burner. Failure to do so could affect the flame appearance and performance of the unit.

22.Place conversion label on valve.

23.Reinstall the right and left log bracket assembly.

24.Reinstall the rear log bracket.

25.Replace logs.

26.Replace glass and stove front.

Conversion is complete.

Left Burner Leg

Injector Shoulder

90°

ST353

Fig. 57 Be sure to maintain 90° angle at left burner leg.

Table 2. Injector Orifice Size Matrix

 

Conversion to Natural Gas

 

Input (BTU/h)

Kit #

Front

Part #

 

Rear

Part #

Minimum

Maximum

000-5021

#54 / .055”

30000514

 

#44 / .086”

30000334

19,000

28,000

 

Conversion to LP

 

 

Input (BTU/h)

Kit #

Front

Part #

 

Rear

Part #

Minimum

Maximum

000-5022

#69 / .029”

30000513

 

#54 / .055”

30000514

20,000

28,000

28

30001935

Image 28
Contents Direct Vent / Natural Vent Gas Heater Table of Contents General Information Verify proper operation after servicingDutchwest Direct Vent / Natural Vent Dimensions Dutchwest dimensionsInstallation Requirements Locating the StoveWall and Ceiling Clearances Wall Centerline from FloorHearth Requirements Gas Specifications Gas Inlet and Manifold PressuresHorizontal Termination Direct Vent only Input ModelVertical Termination Direct Vent only Vent Termination ClearancesVenting Termination Clearances Location of Vent TerminationCanadian Installations1 US Installations2 General Venting Information Termination LocationVenting Requirements Natural Vent Only Termination ClearancesVenting Requirements and Options Direct Vent only Approved Vent System ComponentsInstall the Optional Fan Remove rear skirt insertInstall the Vent Adapter Pipe Venting System Assembly Direct Vent General InformationAttach the Inner Vent Assembly to the stove Side Wall Termination Assembly Simpson DuraVent install inner adapter pipeDetermine the vertical pipe length Vertical Through the Roof Vent Assembly Vent Termination Below GradeVenting System Assembly Natural Vent General Information Install the Vent PipeInstall the Log Set Connect the Gas Supply LineAir Shutter Adjustment Burner InformationComplete the Assembly Install ON/OFF SwitchInstall the Stove Front Thermostat Connection optionalThermostat Maximum RunFlame & Temperature Adjustment Flame CharacteristicsOperation Your First FireLighting and Operating Instructions To Turn Off Gas To HeaterTroubleshooting / Honeywell #8420 Gas Control System Symptom Possible Causes Corrective ActionConversion Precautions Conversion ProcedureFuel Conversion Instructions Honeywell ValvePilot Orifice Conversion Pilot TypeInjector Orifice Size Matrix Maintenance Stove Disassembly Gasket ReplacementInspect the Vent System Annually Wiring Diagrams Power Cord FANDescription Dutchwest 16a,bDutchwest Direct Vent / Natural Vent Gas Heater Fuel Conversion KitsOptional Accessories Remote ControlsFan Kits Decorative RingsLimited Lifetime Warranty Efficiency Ratings Model EnerGuide Ratings Fireplace Efficiency %

2466, 2465 specifications

Vermont Casting's 2465 and 2466 stoves are renowned in the world of wood-burning appliances, celebrated for their blend of traditional craftsmanship, modern technology, and efficient features. These stoves bring warmth and aesthetic appeal to any home while providing an eco-friendly heating solution.

The Vermont Casting 2465 model stands out with its classic styling and robust construction, made from high-quality cast iron. Its design not only provides durability but also enhances heat retention, allowing for longer-lasting warmth in your space. Featuring a large viewing window, the 2465 allows you to enjoy the mesmerizing flames while also providing ample heat output, making it a focal point of any room.

Similarly, the Vermont Casting 2466 shares many characteristics with its counterpart but introduces slightly elevated features. One of the notable features of the 2466 is its increased heating capacity, suitable for larger homes or open-concept living spaces. Both models are equipped with a user-friendly air control system that optimizes airflow and combustion, ensuring that wood burns more efficiently and cleanly. This results in minimal smoke emissions and contributes to a lower environmental impact.

One of the standout technologies in both the 2465 and 2466 is the patented “Dual Air Control” system. This innovative design allows homeowners to easily adjust the airflow for more efficient burning, regardless of the type of wood used, enhancing combustion efficiency. Users can start with a higher airflow for a quick fire start and then throttle back once the wood is burning well, ensuring an effective and adjustable burn rate.

Additionally, both models come with an integrated ash pan located at the bottom, designed to simplify maintenance by making ash removal quick and easy. The stoves also feature a built-in heat shield that helps to increase the heating efficiency of the stove while reducing the clearance needed for safe installation.

Overall, the Vermont Casting 2465 and 2466 stoves represent an intersection of function and beauty. Their classic cast iron design paired with modern heating technologies makes them a perfect choice for those wishing to combine traditional aesthetics with efficiency and environmental responsibility in their home heating solutions. Whether you're heating a cozy cabin or a spacious family room, these stoves deliver exceptional performance and timeless appeal.