Desa Tech RFP28TC installation manual Locating Heater, Check GAS Type, Installation Items

Page 9

OWNER’S MANUAL

INSTALLATION

NOTICE: This heater is intended for use as supplemental heat. Use this heater along with your pri- mary heating system. Do not in- stall this heater as your primary heat source. If you have a central heating system, you may run system’s circulating blower while using heater. This will help circu- late the heat throughout the house. In the event of a power outage, you can use this heater as your primary heat source.

NOTICE: A qualified service per- son must install heater. Follow all local codes.

LOCATING HEATER

WARNING: Maintain the mini- mum clearances shown in Figure

10.If you can, provide greater clearances from floor, ceiling, and joining wall.

You can locate heater on floor. The optional hearth base is needed. You can also install the optional decorative mantel on the heater (some mantels require hearth base).

IMPORTANT: Only use optional mantel and hearth base specified in this manual. Purchase the optional mantel and hearth base from your dealer. See Accessories, page 25.

The heater may also be mounted on a wall. You cannot use optional mantel if mounting heater on a wall.

CAUTION: If you install the heater in a home garage

•heater pilot and burner must be at least 18 inches above floor.

•locate heater where moving ve- hicle will not hit it.

For convenience and efficiency, install heater

•where there is easy access for operation, inspection, and service.

•in coldest part of room.

An optional fan kit is available from your dealer. See Accessories, page 25. If plan- ning to use fan, locate heater near an electri- cal outlet.

CEILING

CHECK GAS TYPE

Use only propane/LP gas. If your gas supply is not propane/LP, do not install heater. Call dealer where you bought heater for proper type heater.

WARNING: Never install the heater

• in a bedroom or a bathroom

•

in a recreational vehicle

•

where curtains,

furniture,

 

clothing, or other

flammable

6" Minimum From Sides Of Heater

36" Minimum

INSTALLATION ITEMS

Before installing heater, make sure you have the items listed below.

•external regulator (supplied by installer)

•piping (check local codes)

•sealant (resistant to propane/LP gas)

•manual shutoff valve *

•ground joint union

•test gauge connection *

•sediment trap

•tee joint

•pipe wrench

*An A.G.A. design-certified manual shutoff valve with 1/8" NPT tap is an acceptable alternative to test gauge connection. Pur- chase the optional A.G.A. design-certified manual shutoff valve from your dealer. See Accessories, page 25.

objects are less than 36 inches

from the front, top, or sides of

the heater

• as a fireplace insert

• in high traffic areas

• in windy or drafty areas

CAUTION: This heater cre- ates warm air currents. These currents move heat to wall sur- faces next to heater. Installing heater next to vinyl or cloth wall coverings or operating heater where impurities (such as to- bacco smoke, aromatic candles, cleaning fluids, oil or kerosene lamps, etc.) in the air exist, may discolor walls.

IMPORTANT: Vent-free heaters add mois- ture to the air. Although this is beneficial, installing heater in rooms without enough ventilation air may cause mildew to form from too much moisture. See Air for Com- bustion and Ventilation, pages 6 through 8.

Left

Right

Side

Side

 

Minimum To

 

Top Surface

FLOOR

5" Of Carpeting,

Tile Or Other

 

Combustible

 

Material

Figure 10 - Mounting Clearances As Viewed From Front of Heater

Continued

103509

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents What to do if YOU Smell GAS OWNER’S Operation and Installation Manual RFP28TCVENT-FREE Radiant Flame Heater Safety InformationProduct Identification Product FeaturesLocal Codes UnpackingInstalling Log AssemblyAssembling Heater Removing Front Panel Of HeaterAssembling Brass Trim Assembling and Attaching Brass TrimProviding Adequate Ventilation AIR for Combustion and VentilationUnusually Tight Construction Confined and Unconfined SpaceAIR for Combustion Ventilation Determining FRESH-AIR Flow for Heater LocationDetermining if You Have a Confined or Unconfined Space Ventilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Installation Items InstallationLocating Heater Check GAS TypeInstallation Options Thermostat Sensing BulbMounting Heater to Wall Installing Bottom Mounting Screws Attaching To Wall Anchor MethodPlacing Heater On Mounting Bracket Optional Hearth Base Mounting Heater onMounting Heater with To Optional MantelInstalling Mantel to Heater Connecting to GAS SupplyPressure Testing Heater Gas Connections Pressure Testing Gas Supply Piping SystemChecking GAS Connections Test Pressures In Excess Of 1/2 PsigOperating Heater For Your Safety Read Before LightingLighting Instructions To Turn OFF GAS To ApplianceInspecting Burner Manual Lighting ProcedureThermostat Control Operation Pilot Flame PatternObserved Problem Possible Cause Remedy TroubleshootingObserved Problem Possible Cause Gas leak. See Warning statement at TopSpecifications Cleaning and MaintenanceService Hints Technical ServiceParts Under Warranty Replacement Parts Parts CentralsParts not Under Warranty Four Flags Power ProductsRFP28TC Illustrated Parts BreakdownKEY Part Number Description Parts ListAccessories 103509 Warranty Information

RFP28TC specifications

Desa Tech RFP28TC is an advanced piece of technology that stands out in today’s competitive market. This robust device is designed to meet the diverse needs of various industries, from manufacturing to healthcare, ensuring efficient operations and seamless functionality.

One of the main features of the RFP28TC is its high processing power and speed. Equipped with a state-of-the-art processor, it can handle multiple tasks simultaneously without any lag. This enhances productivity, allowing businesses to maximize their output and minimize downtime.

The RFP28TC is built using cutting-edge technologies that ensure durability and reliability. Its robust chassis is designed to withstand harsh working conditions, making it ideal for environments such as factories and distribution centers. Furthermore, its energy-efficient design helps reduce operational costs, contributing to sustainability efforts while providing consistent performance.

In terms of connectivity, the RFP28TC offers a variety of options, including Wi-Fi, Bluetooth, and Ethernet. This versatility allows for seamless integration into existing networks, enabling real-time data sharing and communication across devices. Such a feature is particularly beneficial for companies looking to implement Internet of Things (IoT) solutions, where interconnected devices work together to optimize efficiency.

The user interface of the RFP28TC is designed with usability in mind. Featuring an intuitive touchscreen, it allows users to navigate through various applications effortlessly. This ease of use reduces the learning curve for new operators and ensures that employees can get to work quickly.

Another notable characteristic of the RFP28TC is its comprehensive support for various software applications. Whether it’s for inventory management, data analytics, or customer relationship management, the device supports a wide range of platforms, making it suitable for different sectors. This flexibility means that businesses can customize their technology to fit their specific needs.

Security is a top concern for many organizations, and the RFP28TC addresses this with advanced encryption and access control features. These security measures protect sensitive information, ensuring compliance with industry regulations and safeguarding against potential threats.

In conclusion, the Desa Tech RFP28TC is a powerful and flexible solution that combines high performance, robust design, and advanced connectivity. Its user-friendly interface and extensive software compatibility make it an invaluable tool for businesses across various industries, driving efficiency and innovation while prioritizing security and reliability.
Top Page Image Contents