Enviro EF3 owner manual Freestanding hearth mount installation overview

Page 24

Installation

���� ���

����� ������

���� ����� ������ ������

�������� ������� ����

���� ���� ������� ����

��������� ���� ���� ��

����� �� �����

�������� ���� ���������

���� ���� � ���� �������

������� �� ���� �� ����

���� ��������� ������

�� ����� ������

��������� ������

��������

����� ��� ���

�������� ���������

������ ���

Figure 30: Freestanding hearth mount installation overview.

MASONRY FIREPLACE INSTALLATION - FIREPLACE INSERT:

The fireplace insert model requires a surround panel and a pedestal. When installing this unit, ensure that the pedestal is removed from the inside of the hopper and installed on the bottom of the unit (see

“PEDESTAL INSTALLATION”).

Assemble surround panel (see “ASSEMBLING THE SURROUND PANEL - FIREPLACE INSERT”) before starting installation.

A non-combustible hearth pad must cover combustible flooring underneath, as well as 6” (150 mm) in front of the heater and 6” (150 mm) to the side of the heater.

1.Install the hearth pad.

2.Lock the fireplace damper in the open position.

3.Install a positive flue connector at the fireplace damper.

24

Image 24
Contents EF3 Table of Contents Introduction I. Pellet StandardsStore pellets at least 36 1 m away from the pellet stove USE of Cordwood is Prohibited by LAW Keep ASH PAN Free of RAW Fuel Reasons WHY the Unit Overheated Operating InstructionsSpecial Notes Seconds on Thermostat / Switch Mode Initial START-UP See aboveStove Dial-A-Fire control panelRoutine Cleaning and Maintenance Tools Required to Clean UnitBurn POT and Liner 2-3 days Inside Firebox weeklyRemoval of the firebox backing for bi-annual cleaning Freestanding ASH PANHeat Exchanger Tubes 2-3 days Fresh AIR Intake seasonPost Season CLEAN-UP Cleaning Plated SurfacesBrick Panel Installation Screws to take out to remove stove from palletDimensions of EF3 Freestanding Minimum Alcove width Inches 91 cm Minimum Alcove height Or from the outside of the pedestal for the FPI or BIH EF3 Built-In Heater recommended FramingVent surfaces can Install Vent AT Clearances Specified by Venting Manufacturer Fresh Air Intake Place the appliance 15 37.5 cm Is the recommended installation set up Inside Vertical Installation Outside Vertical Installation Freestanding hearth mount installation overview Connect a tee or 90 degree This unit includes a 3 75 mm pedestal Corner Brackets Removal Side surround panel swings forwardTroubleshooting Do notWhat to do if Stove will not start. GeneralStove will not operate when hot. General Exhaust motor will not function normally. GeneralConvection blower will not function normally. General Auger motor will not function normally. General Dial-a-fire has no effect on the fire Timer Control Only 200F 93C high limit temperature sensor has trippedPotentiometer Readings Stove will not shut off. General Stove keeps going outFuses Wiring Diagram Wiring Diagram Timer ControlParts List Reference Description Part NumberParts List Options ComponentsDiagramParts Parts Diagram Steel Warranty To the DistributorFor the do-it-yourself Individual Installation Data Sheet Name of Owner Address
Related manuals
Manual 38 pages 19.67 Kb

EF3 specifications

The Enviro EF3 is an innovative and eco-friendly vehicle that is transforming the landscape of sustainable transportation. With a focus on efficiency, performance, and environmental responsibility, the EF3 represents a significant leap forward in automotive technology.

One of the standout features of the Enviro EF3 is its advanced electric powertrain. This vehicle is equipped with a state-of-the-art electric motor that provides impressive torque and acceleration while remaining silent and efficient. The electric motor is powered by a high-capacity lithium-ion battery pack, which can be charged quickly and has a long lifespan. This allows for extended driving ranges, making the EF3 ideal for both urban commuting and longer journeys.

The EF3 also incorporates regenerative braking technology, which captures energy that would otherwise be lost during braking. This innovative feature helps to recharge the battery while enhancing overall energy efficiency. As a result, drivers can enjoy longer trips and reduced charging frequency, while also minimizing the vehicle's overall environmental impact.

In terms of design, the Enviro EF3 boasts a sleek, aerodynamic profile that not only looks modern but also contributes to its overall efficiency. The vehicle's exterior is crafted using lightweight materials, which enhance performance and help to maximize range. Additionally, the spacious interior is designed with comfort and sustainability in mind. Eco-friendly materials are used throughout the cabin, ensuring that the EF3 remains a green choice even inside the vehicle.

Connectivity is another vital characteristic of the Enviro EF3. Equipped with the latest infotainment and navigation technologies, the vehicle offers seamless integration with smartphones and other devices. This feature allows drivers to access real-time traffic updates, manage charging schedules, and even control various vehicle settings from their mobile devices.

Safety is prioritized in the design of the EF3, with advanced driver-assistance systems (ADAS) that include features such as adaptive cruise control, lane-keeping assist, and collision avoidance technology. These systems work together to enhance driver confidence and ensure a safe driving experience.

In conclusion, the Enviro EF3 represents the future of sustainable transportation. With its electric powertrain, advanced technologies, aerodynamic design, and a strong focus on safety and connectivity, the EF3 is a versatile and eco-friendly vehicle that meets the demands of modern drivers while contributing to a healthier planet. As more consumers seek environmentally responsible choices, the Enviro EF3 stands out as a leading option in the electric vehicle market.