Enviro EF3 owner manual This unit includes a 3 75 mm pedestal

Page 26

 

 

Installation

INSTALLATION FOR A BUILT-IN HEATER:

 

Combustible

 

This unit includes a 3” (75 mm) pedestal

 

and surrounding faceplates. The part of the

materials and

 

structure

 

unit behind the faceplate can be enclosed

 

 

 

with combustible material. It has 1” (25

Surround Panel

Wall

mm) standoffs to establish clearances to

 

 

thimble

combustibles to the back, top and sides.

 

 

12"

Refer to “CLEARANCES TO COMBUSTIBLES - BUILT-IN

 

 

(30.5 cm)

 

 

45°

HEATER“ and Figure 12 and 13 for the size

 

 

and placement of the alcove to be built for

 

 

elbow

 

 

 

the unit.

6"

 

Rodent

For the venting refer to “HORIZONTAL EXHAUST

(15 cm)

 

mesh cap

THROUGH WALL INSTALLATION - FREESTANDING“.

 

 

Fresh air

 

 

 

intake

 

Non-combustible

 

Existing floor

 

 

(combustible)

 

floor protection.

3" (7.5 cm)

 

 

Pedestal

 

 

Figure 32: Built-in heater installation.

 

INSTALLATION OF CONTROL PANEL INTO SURROUND PANEL - FPI AND BIH:

When installing the control panel into the surround panel, the surround does not need to be assembled. The control board will be found in behind the firebox.

Place the control panel on the backside of the right surround panel so the hinge is on the outside and the top and bottom holes on the control panel line up with those on the surround. Attach using two (2) T-20 screws through the front of the surround into the circuit board control panel.

After the surround has been assembled and is ready to be installed on the unit, plug the wiring harness into the control panel (see Figure 32).

Figure 33: Control

Panel Cover.

THE TUBE SCRAPER ROD:

����

Figure 34: Control

Panel Back.

Put the stainless steel rod through the hole in the heat exchanger located behind the top louvers. Thread the rod into the scraper plate, which is visible from inside the firebox by removing the top baffle.

Figure 35: Tube scrapper rod

placement.

26

Image 26
Contents EF3 Table of Contents Store pellets at least 36 1 m away from the pellet stove IntroductionI. Pellet Standards USE of Cordwood is Prohibited by LAW Keep ASH PAN Free of RAW Fuel Special Notes Reasons WHY the Unit OverheatedOperating Instructions Seconds on Thermostat / Switch Mode Initial START-UP See aboveStove Dial-A-Fire control panelBurn POT and Liner 2-3 days Routine Cleaning and MaintenanceTools Required to Clean Unit Inside Firebox weeklyHeat Exchanger Tubes 2-3 days Removal of the firebox backing for bi-annual cleaningFreestanding ASH PAN Fresh AIR Intake seasonBrick Panel Post Season CLEAN-UPCleaning Plated Surfaces Installation Screws to take out to remove stove from palletDimensions of EF3 Freestanding Minimum Alcove width Inches 91 cm Minimum Alcove height Or from the outside of the pedestal for the FPI or BIH EF3 Built-In Heater recommended FramingVent surfaces can Install Vent AT Clearances Specified by Venting Manufacturer Fresh Air Intake Place the appliance 15 37.5 cm Is the recommended installation set up Inside Vertical Installation Outside Vertical Installation Freestanding hearth mount installation overview Connect a tee or 90 degree This unit includes a 3 75 mm pedestal Corner Brackets Removal Side surround panel swings forwardWhat to do if TroubleshootingDo not Stove will not start. GeneralConvection blower will not function normally. General Stove will not operate when hot. GeneralExhaust motor will not function normally. General Auger motor will not function normally. General Potentiometer Readings Dial-a-fire has no effect on the fire Timer Control Only200F 93C high limit temperature sensor has tripped Stove will not shut off. General Stove keeps going outFuses Wiring Diagram Wiring Diagram Timer ControlParts List Reference Description Part NumberParts List Options ComponentsDiagramParts Parts Diagram Steel For the do-it-yourself Individual WarrantyTo the Distributor Installation Data Sheet Name of Owner Address
Related manuals
Manual 38 pages 19.67 Kb

EF3 specifications

The Enviro EF3 is an innovative and eco-friendly vehicle that is transforming the landscape of sustainable transportation. With a focus on efficiency, performance, and environmental responsibility, the EF3 represents a significant leap forward in automotive technology.

One of the standout features of the Enviro EF3 is its advanced electric powertrain. This vehicle is equipped with a state-of-the-art electric motor that provides impressive torque and acceleration while remaining silent and efficient. The electric motor is powered by a high-capacity lithium-ion battery pack, which can be charged quickly and has a long lifespan. This allows for extended driving ranges, making the EF3 ideal for both urban commuting and longer journeys.

The EF3 also incorporates regenerative braking technology, which captures energy that would otherwise be lost during braking. This innovative feature helps to recharge the battery while enhancing overall energy efficiency. As a result, drivers can enjoy longer trips and reduced charging frequency, while also minimizing the vehicle's overall environmental impact.

In terms of design, the Enviro EF3 boasts a sleek, aerodynamic profile that not only looks modern but also contributes to its overall efficiency. The vehicle's exterior is crafted using lightweight materials, which enhance performance and help to maximize range. Additionally, the spacious interior is designed with comfort and sustainability in mind. Eco-friendly materials are used throughout the cabin, ensuring that the EF3 remains a green choice even inside the vehicle.

Connectivity is another vital characteristic of the Enviro EF3. Equipped with the latest infotainment and navigation technologies, the vehicle offers seamless integration with smartphones and other devices. This feature allows drivers to access real-time traffic updates, manage charging schedules, and even control various vehicle settings from their mobile devices.

Safety is prioritized in the design of the EF3, with advanced driver-assistance systems (ADAS) that include features such as adaptive cruise control, lane-keeping assist, and collision avoidance technology. These systems work together to enhance driver confidence and ensure a safe driving experience.

In conclusion, the Enviro EF3 represents the future of sustainable transportation. With its electric powertrain, advanced technologies, aerodynamic design, and a strong focus on safety and connectivity, the EF3 is a versatile and eco-friendly vehicle that meets the demands of modern drivers while contributing to a healthier planet. As more consumers seek environmentally responsible choices, the Enviro EF3 stands out as a leading option in the electric vehicle market.