Enviro EF3 owner manual Corner Brackets

Page 27

Installation

INSTALLATION AND REMOVAL OF THE SURROUND PANELS - FPI AND BIH:

Corner Brackets

Two (2) pieces make

up one (1) corner bracket

Magnetic Strips

Figure 36: Assembling Trim for Surround Panel.

1.Assemble the trim set using the corner hardware and screws supplied in the surround panel packaging. Install corner hardware into the side trim pieces, then push them into the top trim. Do not over-tighten the corners or the side trim cannot be removed during servicing. See Figure 36.

2.Using three (3) T-20 screws on each side attach the hinges on the side surround panels to the unit’s side panels (refer to Figure 37).

3.Plug the wiring harness into the control panel (see Figure 34).

4.Loosen the front hopper lid screws and center the top surround panel under the hopper lid, tighten screws.

5.Insert each side panel anchor bolt through the top panel into the corresponding side panel holes and

tighten using a 7/16” wench or socket (refer to Figure 38).

6. Place assembled trim over the surround assembly.

Figure 37: Panel placed on unit.

Figure 38: Assembling the Surround Panel,

back view.

27

Image 27

Contents EF3 Table of Contents Introduction I. Pellet StandardsStore pellets at least 36 1 m away from the pellet stove USE of Cordwood is Prohibited by LAW Keep ASH PAN Free of RAW Fuel Reasons WHY the Unit Overheated Operating InstructionsSpecial Notes Seconds on Initial START-UP See above Thermostat / Switch ModeDial-A-Fire control panel StoveInside Firebox weekly Routine Cleaning and MaintenanceTools Required to Clean Unit Burn POT and Liner 2-3 daysFresh AIR Intake season Removal of the firebox backing for bi-annual cleaningFreestanding ASH PAN Heat Exchanger Tubes 2-3 daysPost Season CLEAN-UP Cleaning Plated SurfacesBrick Panel Screws to take out to remove stove from pallet InstallationDimensions of EF3 Freestanding Minimum Alcove width Inches 91 cm Minimum Alcove height EF3 Built-In Heater recommended Framing Or from the outside of the pedestal for the FPI or BIHVent surfaces can Install Vent AT Clearances Specified by Venting Manufacturer Fresh Air Intake Place the appliance 15 37.5 cm Is the recommended installation set up Inside Vertical Installation Outside Vertical Installation Freestanding hearth mount installation overview Connect a tee or 90 degree This unit includes a 3 75 mm pedestal Corner Brackets Side surround panel swings forward RemovalStove will not start. General TroubleshootingDo not What to do ifStove will not operate when hot. General Exhaust motor will not function normally. GeneralConvection blower will not function normally. General Auger motor will not function normally. General Dial-a-fire has no effect on the fire Timer Control Only 200F 93C high limit temperature sensor has trippedPotentiometer Readings Stove keeps going out Stove will not shut off. GeneralFuses Wiring Diagram Timer Control Wiring DiagramReference Description Part Number Parts ListParts List Options ComponentsDiagramParts Parts Diagram Steel Warranty To the DistributorFor the do-it-yourself Individual Name of Owner Address Installation Data Sheet

Related manuals

Manual 38 pages 19.67 Kb

EF3 specifications

The Enviro EF3 is an innovative and eco-friendly vehicle that is transforming the landscape of sustainable transportation. With a focus on efficiency, performance, and environmental responsibility, the EF3 represents a significant leap forward in automotive technology.

One of the standout features of the Enviro EF3 is its advanced electric powertrain. This vehicle is equipped with a state-of-the-art electric motor that provides impressive torque and acceleration while remaining silent and efficient. The electric motor is powered by a high-capacity lithium-ion battery pack, which can be charged quickly and has a long lifespan. This allows for extended driving ranges, making the EF3 ideal for both urban commuting and longer journeys.

The EF3 also incorporates regenerative braking technology, which captures energy that would otherwise be lost during braking. This innovative feature helps to recharge the battery while enhancing overall energy efficiency. As a result, drivers can enjoy longer trips and reduced charging frequency, while also minimizing the vehicle's overall environmental impact.

In terms of design, the Enviro EF3 boasts a sleek, aerodynamic profile that not only looks modern but also contributes to its overall efficiency. The vehicle's exterior is crafted using lightweight materials, which enhance performance and help to maximize range. Additionally, the spacious interior is designed with comfort and sustainability in mind. Eco-friendly materials are used throughout the cabin, ensuring that the EF3 remains a green choice even inside the vehicle.

Connectivity is another vital characteristic of the Enviro EF3. Equipped with the latest infotainment and navigation technologies, the vehicle offers seamless integration with smartphones and other devices. This feature allows drivers to access real-time traffic updates, manage charging schedules, and even control various vehicle settings from their mobile devices.

Safety is prioritized in the design of the EF3, with advanced driver-assistance systems (ADAS) that include features such as adaptive cruise control, lane-keeping assist, and collision avoidance technology. These systems work together to enhance driver confidence and ensure a safe driving experience.

In conclusion, the Enviro EF3 represents the future of sustainable transportation. With its electric powertrain, advanced technologies, aerodynamic design, and a strong focus on safety and connectivity, the EF3 is a versatile and eco-friendly vehicle that meets the demands of modern drivers while contributing to a healthier planet. As more consumers seek environmentally responsible choices, the Enviro EF3 stands out as a leading option in the electric vehicle market.