Enviro 50-029 owner manual Round Support

Page 13

Initial Installation

QUALIFIED INSTALLERS ONLY

PLANNING YOUR INSTALLATION:

When planning your installation, it will be necessary to select the proper length of vent pipe for your particular requirements. It is important to note when passing through a wall, the maximum allowable wall thickness is 10 inches (25.4 cm), 11⁄2 inches (3.8 cm) clearance to combustibles must be maintained. Select the amount of vertical rise desired for “vertical-to-horizontal” type installations. To determine the length of vent pipe required for vertical installations, measure the distance from the appliance flue outlet to the ceiling, the ceiling thickness, the vertical rise through the attic or second story, and allow for sufficient vent height above the roofline. For two story applications, a fire stop is required at each floor level. If an offset is needed in the attic, additional pipe and elbows will be required. To connect the venting system to the appliance flue outlet, a twist-lock adapter is built into the appliance at the factory. Refer to ‘Vent Configuration and Restrictor Settings’ for venting parameters.

Your total vent pipe length must be within the shaded area of Figure 36. If a 90° elbow is used in the horizontal plane, 36” (91.4 cm) must be subtracted from the allowable horizontal run.

There are two (2) basic types of Direct Vent System installations. The two (2) types of installations are shown below.

Round Support

Box/Wall Thimble

Horizontal

Termination

Pipelength

90° Elbow

Pipelength

Figure 10: Common Horizontal Installation.

Vertical

Termination

Storm Collar

Flashing

Ceiling Firestop

Round Support

Box/Wall Thimble

Cathedral Ceiling

Support Box

Pipelength

Pipelength

Figure 11: Common Vertical Installation.

13

Image 13
Contents What to do if YOU Smell GAS General Safety PrecautionsTable of Contents Vented GAS Fireplace Heater Ascot DV NG/LPG Codes And ApprovalsThis Enviro Ascot Fireplace Dimensions of the Ascot SpecificationsOperating Instructions For Your Safety Read Completely Before OperatingMaintenance And Service Removing inner glass door To ReplaceTo be Installed by a Qualified Service Agency only Qualified Installers only Initial InstallationAre Permitted to Reach the Outside Vent Termination Vent Restrictor Setting Round Support High temperature silicone on Installing Vent Cap with Vinyl Siding Stand-Off Straight Through Wall Installation Vertical Installation Material overlaps the top edge of the flashing Wiring Diagram InstallationStep A. Installations Canadian InstallationsGeneral Venting Information Venting of a Fireplace Fitted with the Drafthood AdaptorSpill Switch Replacement Automatic Safety Shut DownOptional Finishing Hearth Mount Installation To Test Valve Pressures GAS Line ConnectionControls Wiring Errors Can Cause Improper Ascot Burner Tray Secondary InstallationEmber Placement Problem Possible Cause Solution Trouble ShootingReference Description Part Number Parts ListCast Description Reference Cast Description Part Number Parts Diagram To the Distributor WarrantyInstallation Data Sheet

50-029 specifications

Enviro 50-029 is an innovative environmental monitoring device designed to provide comprehensive data collection and analysis for various ecological parameters. With its cutting-edge features, the device has garnered attention in industries such as agriculture, environmental science, and urban planning.

One of the cornerstone features of the Enviro 50-029 is its multi-sensor capability. This device is equipped with a suite of sensors that can measure a wide range of environmental variables. These include temperature, humidity, air quality, soil moisture, and light intensity. The integration of multiple sensors allows users to gather detailed insights into the ecosystem, enabling better decision-making and resource management.

The Enviro 50-029 also utilizes advanced wireless communication technologies, such as LoRaWAN and Zigbee. This allows for real-time data transmission without the need for extensive wiring or infrastructure. The device can connect to a central hub or cloud-based platform, facilitating remote monitoring and accessibility of data from anywhere in the world. This feature is particularly valuable for researchers and environmental agencies monitoring remote or hard-to-reach areas.

Power efficiency is another significant characteristic of the Enviro 50-029. Utilizing low-power design protocols, the device can operate for extended periods on minimal battery power. This sustainability aspect is crucial, particularly for long-term environmental monitoring projects where replacing batteries frequently can be logistically challenging.

Moreover, the Enviro 50-029 is built to withstand various environmental conditions. Its robust, weather-resistant casing ensures durability in extreme temperatures and harsh weather environments. This makes it suitable for outdoor deployments, whether in agricultural fields, forests, or urban areas, without compromising performance.

The device also supports customizable settings, enabling users to define specific thresholds and alerts for different environmental parameters. This feature allows for proactive monitoring and notifications on critical changes, providing essential data needed to respond to environmental concerns swiftly.

Overall, the Enviro 50-029 stands out as a versatile and reliable tool for environmental monitoring. Its multi-sensor capabilities, advanced communication technologies, power efficiency, and robust design make it an excellent choice for research, conservation efforts, and smart farming applications. By integrating such a sophisticated device into their operations, users can gain actionable insights and contribute to a more sustainable future.