Enviro 50-029 Operating Instructions, For Your Safety Read Completely Before Operating

Page 6

Operating Instructions

FOR YOUR SAFETY READ COMPLETELY BEFORE OPERATING.

LIGHTING INSTRUCTIONS:

CAUTION:Hot while operating. Do not touch. Keep children, clothing, furniture, gasoline or other flammable vapors away.

FOR YOUR SAFETY: Do not operate this fireplace with the glass removed, cracked or broken. Replacement of this glass should be done by a licensed or qualified person! This appliance needs fresh air for safe operation and must be installed with provisions for combustion and ventilation air.

See installation and operating instructions manual. Keep burner and control compartment clean . WARNING: Improper installation, adjustment, alteration, service or maintenance can cause property damage, personal injury, or loss of life. Refer to owners manual. Installation and service must be performed by qualified installer, service agency or the gas supplier.

FOR YOUR SAFETY READ BEFORE OPERATING

WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, AFIREOR EXPLOSION MAY RESULT CAUSING

PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

A)This appliance is e quippe d with a pilot, which mustbe litbyIf you cannot re ach your gas supp lier, call the fire departm ent. hand b y following these instructions e xactly.

B)BEFORE LIGHTING smell all around the appliance area for gas and n ext to the floor because some gas is heavi er

than air and will se ttle on the floor.

WHAT TO DO IF YOU SMELL GAS:

Do not try to light any a pplian ce. Do not touch a ny electrical switch: do not use any phone in you r building.

Immediately call your gas sup plier from a neighbors p hone. Follo w the gas supplie rs instr uctions.

C)Use only your ha nd to p ush in or tu rn the gas co ntrol knob,

 

Neve r use tools. If the knob will not push in or turn by

 

hand , do n ot try to rep air it.

 

Call a qual ified service techn ician. Force or attempte d

D)

repair may result in a fire or explosion.

Do n ot use thisa pplian ce if any part has b een u nder water.

 

Immediately call a qualified service technician to inspe ct

 

the a ppliance an d to replace any pa rt of the con trol system

 

and any ga s con trol which ha s been unde r water.

LIGHTING INSTRUCTIONS

1.STOP! Read th e safe ty information above on th is labe l.

2.Turn off all electrical power to this applian ce.

3. Turn off the gas contr ol knob clockwise

to the off

position.

 

4.Open door. Wa it five (5) minutes to clear outany gas.

 

Cl ose do or. If you sme ll gas, includ ing ne ar the floor ,

 

STOP! Follow “ B” in the

above safety information.

5.

If you do not smell gas go to the ne xt ste p

Fin d pilo t-locate d to th e righ t behin d the side log. Turn

 

the gas control

 

 

kn ob cou nter-clockwise

to “PILOT”.

 

Push the gas co ntrol in

 

ful ly and hold, Keep knob

depressed for a bout 30 seco nds after pilot is lit. Release kno b. If p ilot goes out, rep eatsteps 4 through 5.

WARNING: this gas valve ha s a lockout device, which will n ot allow the pilot burner to be relit until the ther mocouple h as cooled. If the knob does not po p up when released, stop and imme diately call yo ur service technician or gas supplier.

If the pilot does not stay lit after several tries, turn the gas control knob to “OFF” and call your service technician or g as supplier.

6.Turn the gas control knob counter clockwise to the “ON” position. Flip the burner switch to

“ON” THEN TURN THE “HI/LOW” knob to the desired setting. 7. Turn on the ele ctrical power to the unit.

TO TURN OFF GAS TO APPLIANCE

1.

Fli p burn er switch to “OFF”

to th e “OF F”

3 . Turn off all electrical po wer to the ap pliance if service i sto

2.

Turn the gasco ntrol knob clockwise

be performe d.

 

po sition

 

ACLIE -1

 

 

 

Figure 3. Lighting instruction label.

PILOT LIGHT:

1.Turn off the gas to the fireplace. If not recently done, remove the glass and let the unit air out for at least five (5) minutes to clear out any gas. Turn on gas to the heater. Leak test all joints with soapy water. NEVER USE AN OPEN FLAME FOR LEAK TESTING.

2.Start the pilot by pressing the gas control knob and turning it to PILOT. While holding the gas control knob in, press the piezo ignitor several times until the pilot light starts. Hold the gas control knob in for thirty (30) seconds. Check that the pilot has fully engulfed the thermocouple assembly (see Figure 4).

3.Start the main burner by turning the gas control knob to ON and then turn the rocker switch to ON. Check that all burner ports have flame.

4.Leak test all gas joints again.

����������

������������

Figure 4. Pilot flame.

6

Image 6
Contents What to do if YOU Smell GAS Safety Precautions GeneralTable of Contents Codes And Approvals Vented GAS Fireplace Heater Ascot DV NG/LPGThis Enviro Ascot Fireplace Specifications Dimensions of the AscotFor Your Safety Read Completely Before Operating Operating InstructionsMaintenance And Service To Replace Removing inner glass doorTo be Installed by a Qualified Service Agency only Initial Installation Qualified Installers onlyAre Permitted to Reach the Outside Vent Termination Vent Restrictor Setting Round Support High temperature silicone on Installing Vent Cap with Vinyl Siding Stand-Off Straight Through Wall Installation Vertical Installation Material overlaps the top edge of the flashing Installation Wiring DiagramStep General Venting Information Canadian InstallationsA. Installations Venting of a Fireplace Fitted with the Drafthood AdaptorAutomatic Safety Shut Down Spill Switch ReplacementOptional Finishing Hearth Mount Installation GAS Line Connection To Test Valve PressuresControls Wiring Errors Can Cause Improper Secondary Installation Ascot Burner TrayEmber Placement Trouble Shooting Problem Possible Cause SolutionParts List Reference Description Part NumberCast Description Reference Cast Description Part Number Parts Diagram Warranty To the DistributorInstallation Data Sheet

50-029 specifications

Enviro 50-029 is an innovative environmental monitoring device designed to provide comprehensive data collection and analysis for various ecological parameters. With its cutting-edge features, the device has garnered attention in industries such as agriculture, environmental science, and urban planning.

One of the cornerstone features of the Enviro 50-029 is its multi-sensor capability. This device is equipped with a suite of sensors that can measure a wide range of environmental variables. These include temperature, humidity, air quality, soil moisture, and light intensity. The integration of multiple sensors allows users to gather detailed insights into the ecosystem, enabling better decision-making and resource management.

The Enviro 50-029 also utilizes advanced wireless communication technologies, such as LoRaWAN and Zigbee. This allows for real-time data transmission without the need for extensive wiring or infrastructure. The device can connect to a central hub or cloud-based platform, facilitating remote monitoring and accessibility of data from anywhere in the world. This feature is particularly valuable for researchers and environmental agencies monitoring remote or hard-to-reach areas.

Power efficiency is another significant characteristic of the Enviro 50-029. Utilizing low-power design protocols, the device can operate for extended periods on minimal battery power. This sustainability aspect is crucial, particularly for long-term environmental monitoring projects where replacing batteries frequently can be logistically challenging.

Moreover, the Enviro 50-029 is built to withstand various environmental conditions. Its robust, weather-resistant casing ensures durability in extreme temperatures and harsh weather environments. This makes it suitable for outdoor deployments, whether in agricultural fields, forests, or urban areas, without compromising performance.

The device also supports customizable settings, enabling users to define specific thresholds and alerts for different environmental parameters. This feature allows for proactive monitoring and notifications on critical changes, providing essential data needed to respond to environmental concerns swiftly.

Overall, the Enviro 50-029 stands out as a versatile and reliable tool for environmental monitoring. Its multi-sensor capabilities, advanced communication technologies, power efficiency, and robust design make it an excellent choice for research, conservation efforts, and smart farming applications. By integrating such a sophisticated device into their operations, users can gain actionable insights and contribute to a more sustainable future.