Enviro 50-029 owner manual To be Installed by a Qualified Service Agency only

Page 9
Hi/Low Regulator
on Gas Valve
Figure 6. SIT Valve on Ascot.
Ignition
Module

Maintenance And Service

TO BE INSTALLED BY A QUALIFIED SERVICE AGENCY ONLY

FUEL CONVERSION:

Warning: This conversion kit shall be installed by a qualified service agency in accordance with the manufacturer’s instructions and all applicable codes and requirements of the authority having jurisdiction. If the information in these instructions is not followed exactly, a fire, explosion or production of carbon monoxide may result causing property damage, personal injury or loss of life. The qualified service agency is responsible for the proper installation of this kit. The installation is not proper or complete until the operation of the converted appliance is checked

as specified in the manufacturer’s instructions supplied with the kit.

Please read and follow these instructions. Also, please read the instruction guidelines provided by S.I.T. on how to remove and install the HI/LO regulator.

Step 1. Carefully inspect all parts supplied with this conversion kit. Step 2. Shut the gas supply off at the shut-off valve. (CAUTION:

The gas supply shall be shut off prior to disconnecting the electrical power, before proceeding with the conversion.) Step 3. Open the door by lifting the cast iron top off of the unit.

Pull the two handles straight up to unlatch the door. Using the two latches lift the door assembly straight up and out

of the unit. Swing the front doors open or remove for access the inside of the firebox.

Step 4. Change the regulator on the front of the gas valve (follow the instructions provided by S.I.T.). Step 5. To change the pilot, simply pull the pilot hood straight up to access the pilot injector. Using a

5/32 inch Allen key, remove the pilot injector.

Step 6. Install the new pilot injector supplied with this conversion kit. Simply screw the new injector inside the pilot hood and reinstall the hood by placing the hood on the assembly, line up the key way, and snap into place.

Step 7. Remove the main burner orifice with a 1⁄2 inch deep socket.

Step 8. Install the new orifice supplied. Be sure to put a bead of pipe-thread sealant or approved Teflon tape on the orifice before installing into the burner assembly.

Step 9. Reinstall the burner tray, log set, embers, and glass. Step 10.Open the shut-off valve at the gas line to the unit.

Step 11.Use a small brush to apply a warm soapy water solution to all gas connections (use a half dish soap and half warm water). If a gas leak is present, bubbling will occur. Gas leaks can be repaired by using an approved pipe thread sealant or approved Teflon tape. NEVER USE A NAKED FLAME WHEN TESTING FOR LEAKS.

Step 12.Re-light the fireplace to ensure proper operation and proper flame appearance.

Step 13.MAKE SURE that the sticker provided by S.I.T. is installed, to signify that the valve has been converted to a different fuel type. Also, make sure that the rating plate has a conversion label to show this unit has been converted to a different fuel type.

A VISUAL CHECK OF THE REGULATOR KNOB IS NECESSARY TO DETERMINE WHETHER OR NOT THE REGULATOR IS THE CORRECT PART. A 50% TURN DOWN REGULATOR WILL HAVE ONLY ONE CORNER

ON THE KNOB

 

 

Conversion Kit should contain the following:

 

 

(1)

50% turn down HI/LO regulator with three (3) T-20 Torx screws

 

(1)

Pilot injector

(1) Burner Orifice

(NG #48 DMS; LP #57 DMS)

Conversion instructions

Pilot Orifice

(NG 0.62 mm; LP 0.35 mm)

Labels to show conversion

 

 

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents What to do if YOU Smell GAS General Safety PrecautionsTable of Contents Codes And Approvals Vented GAS Fireplace Heater Ascot DV NG/LPGThis Enviro Ascot Fireplace Dimensions of the Ascot SpecificationsOperating Instructions For Your Safety Read Completely Before OperatingMaintenance And Service Removing inner glass door To ReplaceTo be Installed by a Qualified Service Agency only Qualified Installers only Initial InstallationAre Permitted to Reach the Outside Vent Termination Vent Restrictor Setting Round Support High temperature silicone on Installing Vent Cap with Vinyl Siding Stand-Off Straight Through Wall Installation Vertical Installation Material overlaps the top edge of the flashing Installation Wiring DiagramStep A. Installations Canadian InstallationsGeneral Venting Information Venting of a Fireplace Fitted with the Drafthood AdaptorAutomatic Safety Shut Down Spill Switch ReplacementOptional Finishing Hearth Mount Installation To Test Valve Pressures GAS Line ConnectionControls Wiring Errors Can Cause Improper Ascot Burner Tray Secondary InstallationEmber Placement Problem Possible Cause Solution Trouble ShootingReference Description Part Number Parts ListCast Description Reference Cast Description Part Number Parts Diagram To the Distributor WarrantyInstallation Data Sheet

50-029 specifications

Enviro 50-029 is an innovative environmental monitoring device designed to provide comprehensive data collection and analysis for various ecological parameters. With its cutting-edge features, the device has garnered attention in industries such as agriculture, environmental science, and urban planning.

One of the cornerstone features of the Enviro 50-029 is its multi-sensor capability. This device is equipped with a suite of sensors that can measure a wide range of environmental variables. These include temperature, humidity, air quality, soil moisture, and light intensity. The integration of multiple sensors allows users to gather detailed insights into the ecosystem, enabling better decision-making and resource management.

The Enviro 50-029 also utilizes advanced wireless communication technologies, such as LoRaWAN and Zigbee. This allows for real-time data transmission without the need for extensive wiring or infrastructure. The device can connect to a central hub or cloud-based platform, facilitating remote monitoring and accessibility of data from anywhere in the world. This feature is particularly valuable for researchers and environmental agencies monitoring remote or hard-to-reach areas.

Power efficiency is another significant characteristic of the Enviro 50-029. Utilizing low-power design protocols, the device can operate for extended periods on minimal battery power. This sustainability aspect is crucial, particularly for long-term environmental monitoring projects where replacing batteries frequently can be logistically challenging.

Moreover, the Enviro 50-029 is built to withstand various environmental conditions. Its robust, weather-resistant casing ensures durability in extreme temperatures and harsh weather environments. This makes it suitable for outdoor deployments, whether in agricultural fields, forests, or urban areas, without compromising performance.

The device also supports customizable settings, enabling users to define specific thresholds and alerts for different environmental parameters. This feature allows for proactive monitoring and notifications on critical changes, providing essential data needed to respond to environmental concerns swiftly.

Overall, the Enviro 50-029 stands out as a versatile and reliable tool for environmental monitoring. Its multi-sensor capabilities, advanced communication technologies, power efficiency, and robust design make it an excellent choice for research, conservation efforts, and smart farming applications. By integrating such a sophisticated device into their operations, users can gain actionable insights and contribute to a more sustainable future.
Top Page Image Contents