Regency Z2510L installation manual Fireplace Enclosure Framing, Clearances Height Requirements

Page 7

INSTALLATION

FAILURE TO USE PARTS MAN- UFACTURED BY REGENCY FIREPLACE INDUSTRIES OR VARIATIONS IN TECHNIQUES AND CONSTRUCTION MATERIAL DE- SCRIBED IN THIS MANUAL MAY CREATE A FIRE HAZARD AND VOID REGENCY’S WARRANTY.

The WarmHearth main unit consists of the following:

1)The main fi re box and heat exchanger

2)The large door with ceramic glass

3)A full brick lining and fl ue baffl e

4)The upper and lower louvers

5)The insulated outside air duct

6)The hearth extension fl oor protector used for fl ush mount installations

7)Hearth Safety Strip

8)The internal blowers system (optional)

9)A Furnace Damper Control (optional)

10)The Masonry Retainer Kit (Optional)

11)Furnace Blower (optional)

requires a minimum 2 in. (50 mm) clearance. A combustible mantle (to a depth of 10 in.) may be installed no closer than 18 in. (457 mm) above the warm air vent.

The chimney must be enclosed when installed in or passing through a living area where com- bustible material or people may come in contact with it. This is important to prevent possible personal injury or fi re hazard.

For any further information, please call your dealer. Special restrictions apply to the front and facing of the fi replace and nearby walls.

WARNING: If insulation is used, do not place the unit against it. Insulation or vapor barriers, if used, must be secured to assure insulation and vapor barriers remain in place and do not affect the required air spaces.

WARNING: Do not pack or fill required air spaces with insulation or other material. No material of any kind is allowed in these areas.

NOTE:

1)Do not insulate the chase cavity with blown or fi ll type insulation materials.

2)Local codes may not require fi restopping at the ceiling level for outside chase installa- tions; however, it is recommended for safety and the reduction of heat loss.

3)We recommend that you insulate at least the fi rst fl oor of the chase to prevent heat loss.

4)Some local codes require 1 hour fi re rating on one or all sides of fi re chases. Check with your local authorities.

FIREPLACE

ENCLOSURE FRAMING

As per the diagram, the framing of the main enclosure should not infringe on the area above the fi replace to the ceiling level. The rear and side walls as well as the face above the fireplace must not extend into the area above the unit.

CLEARANCES AND

HEIGHT

REQUIREMENTS

The WarmHearth may be placed on or near construction materials. The combustion air kit,

fire stop spacer and roof fl ashings (not chase fl ashings) may be placed directly on or against normal construction materials. The chimney

No Combustibles on Face of Unit

Combustibles May Not Extend to Unit Face

Do not notch wallboard around standoffs

The only structure allowed above the unit is on the stand-offs at the front of the unit supporting the header.

The enclosure walls can be framed using any suitable material (2 x 4 - 2 x 6 studs, plywood, gyproc, etc.), 2 x 6 is not acceptable for header.

Normally, framing will be set back to allow sheathing to be flush with the front of the fireplace.

Framing Specifi cations

When framing in the header (directly above the fireplace) DO NOT bring any combustible mate- rial lower than the top of the stand-offs.

Be sure to seal the space between the fi replace and the enclosure above with Wonderboard, Du- rockorothersimilarnon-combustiblesheetingto prevent hot air from entering the enclosure.

CAUTION: ONLY NON-COMBUSTI- BLE MATERIAL LIKE EXPANDED METAL OR CONCRETE BOARDS SUCH AS WONDERBOARD AND DUROCK ETC. MAY BE USED IN THE SPACE BETWEEN THE UNIT AND THE FRAMING.

Clearances to Combustibles

Regency Z2510 WarmHearth

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents WarmHearth Fireplace Regency Fireplace Product Table of Contents Safety Label for Z2510L Safety LabelOptions InstallationRegency Warmhearth Product DetailsImportant Please read and follow these rules for safety Dimensions and SpecificationsClearances Height Requirements Fireplace Enclosure FramingBuilding Structures Cannot Encroach on Chase Location FireplaceHearth Extension No stand-offs are requiredCanada Chimney System ConsiderationsChimney Height Chase EnclosureInstallation Components Installing STAND-OFFSBefore YOU Start SET Warmhearth Into Position Installing the Chimney SystemModel 1st Floor 2nd Floor into Attic Offset Chimney InstallationDo not use water, it will create a steam explosion Internal Blower with Thermo-Disc InstallingInstalling the Blower Systems Outside AIR KITInternal and External Blowers With a Thermodisc Parts List QtyGravity AIR Feed KIT Option External Blower with Thermo-DiscInstallation Installing Your Central Heating SystemMaterials Required Typical Floor Register Masonry Retainer Kit Option Non-Self Supporting, Thin Veneer Facades InstallationFinishing Warmhearth Completing the FacingCompleting the Mantle Finishing DetailsExample Face of Fireplace Flush with Wall Sheathing Masonry Liner Bricks Latch AdjustmentGlass Installation Secondary AIR Tube InstallationSafety Guidelines MaintenanceMaintenance Parts LIST- Firebox & Body Parts ListDescription Parts List BAFFLES, DOOR, Options Warranty Lifetime WarrantyInstaller Please complete the following information

Z2510L specifications

The Regency Z2510L is a standout device in the realm of advanced wireless communication. With its cutting-edge features and robust design, it’s specifically engineered to cater to the demands of both personal and professional use. This device is recognized for its reliable performance, making it a staple for users who require efficiency and versatility.

One of the key features of the Regency Z2510L is its exceptional connectivity options. Equipped with state-of-the-art wireless technology, the device supports multiple frequency bands, ensuring seamless communication across various platforms. This flexibility guarantees that users can stay connected, whether at home, in the office, or on the go.

The Z2510L also boasts an intuitive user interface that enhances the overall user experience. Its well-organized menu system allows users to navigate through various functions with ease, significantly minimizing learning curves. Whether it’s for initiating calls, sending messages, or accessing additional features, the interface is designed with user-friendliness in mind.

A noteworthy characteristic of the Regency Z2510L is its long-lasting battery life. The device is equipped with an energy-efficient battery that supports extended usage without frequent recharging. This aspect is particularly beneficial for professionals who are often on the move and cannot afford downtime. The battery performance is complemented by advanced power management technology, which optimizes usage and extends the overall lifespan of the device.

Durability is another hallmark of the Regency Z2510L. It's built to withstand various environmental conditions, making it a reliable choice for users in demanding situations. Whether exposed to dust, moisture, or extreme temperatures, the device maintains functionality and longevity.

Security features are paramount in today's digital age, and the Z2510L does not disappoint. It incorporates robust encryption protocols designed to safeguard communications. This focus on security ensures that sensitive information remains protected, offering peace of mind to users concerned about data breaches.

Moreover, the Regency Z2510L is equipped with advanced audio technology, providing crystal-clear sound quality during calls. Enhanced noise cancellation features ensure that conversations are uninterrupted and clear, even in busy settings.

In summary, the Regency Z2510L represents a blend of functionality, durability, and advanced technology. With its user-centric design, powerful connectivity, and a host of remarkable features, it serves as a reliable tool for anyone seeking efficient communication solutions. Whether for personal or professional use, the Z2510L is poised to meet the demands of today’s fast-paced world.
Top Page Image Contents