Regency Z2510L Masonry Liner Bricks, Louvers Door Handle, Operating Instructions, First Fire

Page 19

INSTALLATION

MASONRY LINER/

BRICKS

Insulated refractory panels are included to extend the life of the fi replace and help radiate heat more evenly. Make sure Insulating Paper is in place along the bottom, side and rear before bricks are put into place. Insulation batt, 1 in. thick is placed above the top brick baffl e.

Using the diagram to fi nd the correct location of the panels install in the following sequence: sides, rear, bottom, top. Care should be taken not to damage the panels during installation.

THE LOG ANDIRONS SHOULD NOT BE REMOVED.

LOUVERS

DOOR HANDLE

The unit comes with a standard black door or optional gold plated door. After the unit has been installedandthefacingcompletedplacethedoor onto the door hinges. Put hinge cover caps on top of hinge to complete the door. Install the gold spring handle onto the handle bar.

to be a snug fi t in order to prevent it from falling out when a fi re is burning.

OPERATING

INSTRUCTIONS

Draft Control

Both the primary and air wash drafts are control- led by the control rod located under your ash lip. To increase your draft, push left for open, to decrease push right for closed. The draft control box is removable should it require attention. From time to time a high temp lubricant may be needed to keep the draft control sliding easily. It must, however, be re-sealed with RTV, high temperature silicone, when replaced.

The unit comes with standard black louvers but can have Gold Plated Louvers as an option. There are 2 sets of louvers: the top consists of 4 louvers and the bottom has 5 louvers.

To attach the louvers fi rst slide 2 spring nuts into place making sure the smaller holes are on the back of the unit. Louvers are held in place by feeding the two screws through the spring nuts. Louvers can be removed by inserting a screw driver between the louvers and removing the screws.

LATCH ADJUSTMENT

The door latch may require adjustment as the door gasket material compresses after a few

res. Removal of the spacer washer shown in the diagram below will allow the latch to be moved closer to the door frame, causing a tighter seal. Remove and replace the nuts, washer and spacer as shown.

GLASS INSTALLATION

Remove the wire retainer from the door, and place the glass in the door, making sure that the glass gasketing will properly seal your unit. The retainer should be resting on the gasketing not on the glass. Tighten securely, but do not wrench down on the glass as this may cause breakage. Do not substitute materials. If your glass door breaks, do not use your unit until it has been replaced (refer to the Glass Replace- ment section).

Washers Spacer

SECONDARY AIR TUBE

INSTALLATION

1)Slide air tube into the hole on the left hand side of the fi rebox as far as it will go. The notch in the air tube should be facing the right hand side of the fi rebox.

2)Slide the air tube back towards the right side until it locks into place. To lock into position, use a pair of vise grips and tap them with a mallet until the tube locks into place. The air holes should be pointing down toward the primary air opening just inside the bottom of the door opening. The air tube will be diffi cult to snap into place because it has

FIRST FIRE

When your installation is completed and in- spected you are ready for your fi rst fi re.

1)Open draft control fully. To the left is open, to the right is closed.

2)Open fi rebox door and build a small fi re using paper and dry kindling. Secure door on the fi rebox and wait a few minutes for

a good updraft in the fl ue to establish the

re. Leaving the door slightly open will help your fi re start more rapidly and keep glass clean. Add more kindling; then 2 x 2 or 2 x 4 softwood to establish a hot coal bed before adding larger cordwood.

Regency Z2510 WarmHearth

19

Image 19
Contents WarmHearth Fireplace Regency Fireplace Product Table of Contents Safety Label for Z2510L Safety LabelOptions InstallationRegency Warmhearth Product DetailsImportant Please read and follow these rules for safety Dimensions and SpecificationsClearances Height Requirements Fireplace Enclosure FramingBuilding Structures Cannot Encroach on Chase Location FireplaceHearth Extension No stand-offs are requiredCanada Chimney System ConsiderationsChimney Height Chase EnclosureInstallation Components Installing STAND-OFFSBefore YOU Start SET Warmhearth Into Position Installing the Chimney SystemModel 1st Floor 2nd Floor into Attic Offset Chimney InstallationDo not use water, it will create a steam explosion Internal Blower with Thermo-Disc InstallingInstalling the Blower Systems Outside AIR KITInternal and External Blowers With a Thermodisc Parts List QtyGravity AIR Feed KIT Option External Blower with Thermo-DiscInstallation Installing Your Central Heating SystemMaterials Required Typical Floor Register Masonry Retainer Kit Option Non-Self Supporting, Thin Veneer Facades InstallationFinishing Warmhearth Completing the FacingCompleting the Mantle Finishing DetailsExample Face of Fireplace Flush with Wall Sheathing Masonry Liner Bricks Latch AdjustmentGlass Installation Secondary AIR Tube InstallationSafety Guidelines MaintenanceMaintenance Parts LIST- Firebox & Body Parts ListDescription Parts List BAFFLES, DOOR, Options Warranty Lifetime WarrantyInstaller Please complete the following information

Z2510L specifications

The Regency Z2510L is a standout device in the realm of advanced wireless communication. With its cutting-edge features and robust design, it’s specifically engineered to cater to the demands of both personal and professional use. This device is recognized for its reliable performance, making it a staple for users who require efficiency and versatility.

One of the key features of the Regency Z2510L is its exceptional connectivity options. Equipped with state-of-the-art wireless technology, the device supports multiple frequency bands, ensuring seamless communication across various platforms. This flexibility guarantees that users can stay connected, whether at home, in the office, or on the go.

The Z2510L also boasts an intuitive user interface that enhances the overall user experience. Its well-organized menu system allows users to navigate through various functions with ease, significantly minimizing learning curves. Whether it’s for initiating calls, sending messages, or accessing additional features, the interface is designed with user-friendliness in mind.

A noteworthy characteristic of the Regency Z2510L is its long-lasting battery life. The device is equipped with an energy-efficient battery that supports extended usage without frequent recharging. This aspect is particularly beneficial for professionals who are often on the move and cannot afford downtime. The battery performance is complemented by advanced power management technology, which optimizes usage and extends the overall lifespan of the device.

Durability is another hallmark of the Regency Z2510L. It's built to withstand various environmental conditions, making it a reliable choice for users in demanding situations. Whether exposed to dust, moisture, or extreme temperatures, the device maintains functionality and longevity.

Security features are paramount in today's digital age, and the Z2510L does not disappoint. It incorporates robust encryption protocols designed to safeguard communications. This focus on security ensures that sensitive information remains protected, offering peace of mind to users concerned about data breaches.

Moreover, the Regency Z2510L is equipped with advanced audio technology, providing crystal-clear sound quality during calls. Enhanced noise cancellation features ensure that conversations are uninterrupted and clear, even in busy settings.

In summary, the Regency Z2510L represents a blend of functionality, durability, and advanced technology. With its user-centric design, powerful connectivity, and a host of remarkable features, it serves as a reliable tool for anyone seeking efficient communication solutions. Whether for personal or professional use, the Z2510L is poised to meet the demands of today’s fast-paced world.