Regency Z2510L installation manual Outside AIR KIT, Installing the Blower Systems

Page 13

INSTALLATION

INSTALLING THE

WIRING THE WARMHEARTH

OUTSIDE AIR KIT

Combustion air is fed to the fi rebox through a connection on the rear lower left side of the unit. A free fl owing supply of air must be available to this opening at all times. Combustion air may be taken from inside the building if the local building code allows, but performance may suffer. Also, it must go through the 4 in. duct to the connection on the left hand side.

Field wire main power supply to fi replace for fan kit. (All electrical connections should only be performed by a licensed/certifi ed electrician).

CAUTION: Label all wires prior to discon- nection when servicing controls. Wiring errors can cause improper and dangerous operation.

Air drawn from the interior of the building will affect the performance of gas or oil furnaces, and exhaust fans and fan driven appliances. This may cause a negative pressure in the house allowing smoke to back into the home. The preferred source of combustion air is from outside the building. If possible, install the kit on the wind loading side of the building not the leeward or (negative pressure) side.

Note: Do not obtain combustion air from attic, garage or other enclosed space.

1)Putthesuppliedinsulatedairducttoanearby exterior wall. Maximum length of duct is 20 ft. (6.1m). Duct length should be kept to a minimum and as straight as possible. Note: 5 ft. only is supplied with unit. If more than 5 ft. is used, increase the diameter of the duct. Termination should be in an area with good air fl ow.

INSTALLING THE BLOWER SYSTEMS

The WarmHearth Fireplace has been designed to meet a wide range of heating requirements. The radiant heat (through the large glass area) combined with the naturally convected heat, allows the WarmHearth Fireplace to adequately heat an average

sized room. A blower is recommended to assist in heating a larger area or one with wall separations. Through the

use of two separate blower systems,

Regency has developed the three basic blower wir-

ing options listed in the diagrams below. Please read all the descriptions before deciding which option is best suited for your application.

2)Ensure that your air source is not close to automobile exhaust, gas meters or other vents.

3)Cut a 4-1/4 in. hole through the wall and mount the outside air kit.

4)Attach the two ends of the duct (making sure not to damage the insulating cover) after installing the fl ange on the fi replace side. Duct must be secured by screws or clamp.

Outside Air Inlet must be 6 ft. below

the chimney termination point

Blower switch box slides into bottom louver assembly and is screwed into place. Place label on outside of louver as shown.

OPTION 1

Internal Blower with Thermo-Disc

The thermodisc provides the user with more convenient control. By leaving the auto/man switch on AUTO, the thermodisc will shut the fan off automatically when the fi replace is too cool to provide adequate heat.

1)Slide blower under side clips (see directional arrows on diagram) and wire to terminal box. Note: hardwire terminal box before drywalling.

2)Blower switch box slides onto bottom louver and is screwed into place.

3)Place sticker on outside of bottom louver.

Regency Z2510 WarmHearth

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents WarmHearth Fireplace Regency Fireplace Product Table of Contents Safety Label for Z2510L Safety LabelRegency Warmhearth InstallationProduct Details OptionsImportant Please read and follow these rules for safety Dimensions and SpecificationsClearances Height Requirements Fireplace Enclosure FramingHearth Extension Location FireplaceNo stand-offs are required Building Structures Cannot Encroach on ChaseChimney Height Chimney System ConsiderationsChase Enclosure CanadaInstallation Components Installing STAND-OFFSBefore YOU Start SET Warmhearth Into Position Installing the Chimney SystemModel 1st Floor 2nd Floor into Attic Offset Chimney InstallationDo not use water, it will create a steam explosion Installing the Blower Systems InstallingOutside AIR KIT Internal Blower with Thermo-DiscGravity AIR Feed KIT Option Parts List QtyExternal Blower with Thermo-Disc Internal and External Blowers With a ThermodiscInstallation Installing Your Central Heating SystemMaterials Required Typical Floor Register Finishing Warmhearth Non-Self Supporting, Thin Veneer Facades InstallationCompleting the Facing Masonry Retainer Kit OptionCompleting the Mantle Finishing DetailsExample Face of Fireplace Flush with Wall Sheathing Glass Installation Latch AdjustmentSecondary AIR Tube Installation Masonry Liner BricksSafety Guidelines MaintenanceMaintenance Parts LIST- Firebox & Body Parts ListDescription Parts List BAFFLES, DOOR, Options Warranty Lifetime WarrantyInstaller Please complete the following information

Z2510L specifications

The Regency Z2510L is a standout device in the realm of advanced wireless communication. With its cutting-edge features and robust design, it’s specifically engineered to cater to the demands of both personal and professional use. This device is recognized for its reliable performance, making it a staple for users who require efficiency and versatility.

One of the key features of the Regency Z2510L is its exceptional connectivity options. Equipped with state-of-the-art wireless technology, the device supports multiple frequency bands, ensuring seamless communication across various platforms. This flexibility guarantees that users can stay connected, whether at home, in the office, or on the go.

The Z2510L also boasts an intuitive user interface that enhances the overall user experience. Its well-organized menu system allows users to navigate through various functions with ease, significantly minimizing learning curves. Whether it’s for initiating calls, sending messages, or accessing additional features, the interface is designed with user-friendliness in mind.

A noteworthy characteristic of the Regency Z2510L is its long-lasting battery life. The device is equipped with an energy-efficient battery that supports extended usage without frequent recharging. This aspect is particularly beneficial for professionals who are often on the move and cannot afford downtime. The battery performance is complemented by advanced power management technology, which optimizes usage and extends the overall lifespan of the device.

Durability is another hallmark of the Regency Z2510L. It's built to withstand various environmental conditions, making it a reliable choice for users in demanding situations. Whether exposed to dust, moisture, or extreme temperatures, the device maintains functionality and longevity.

Security features are paramount in today's digital age, and the Z2510L does not disappoint. It incorporates robust encryption protocols designed to safeguard communications. This focus on security ensures that sensitive information remains protected, offering peace of mind to users concerned about data breaches.

Moreover, the Regency Z2510L is equipped with advanced audio technology, providing crystal-clear sound quality during calls. Enhanced noise cancellation features ensure that conversations are uninterrupted and clear, even in busy settings.

In summary, the Regency Z2510L represents a blend of functionality, durability, and advanced technology. With its user-centric design, powerful connectivity, and a host of remarkable features, it serves as a reliable tool for anyone seeking efficient communication solutions. Whether for personal or professional use, the Z2510L is poised to meet the demands of today’s fast-paced world.
Top Page Image Contents