Regency U37-NG1 Horizontal Terminations, Optional Components, Alternate Snorkel Termination Cap

Page 13

INSTALLATION

RESIDENTIAL AND MANUFACTURED HOMES /

MOBILE HOMES INSTALLATIONS

You will require the following components with your new Regency® Rear Vent Direct Vent Freestanding Gas Stove. Please review your product to make sure you have everything you need. In the event that you are missing any part, contact your dealer. Decorative brass or chrome trim kits are available from Simpson Dura-Vent for their wall thimbles, as well as a square wall thimble cover.

Note: These are the minimum pieces required.

Other parts may be required for your particular installation.

Minimum components for a Horizontal Installation:

640-944 Horizontal Termination Kit which includes:

16-5/8" Dia. x 18" Black Pipe

14" Dia. x 18" Aluminum Vent

1640-530/P Riser Vent Terminal

1946-202 Wall Penetration Heat Shield (Wall Thimble) (2 pcs)

1640-545/P Decorative Wall Trim (Black)

1948-128 Tube Mill-Pac

 

Screws

Optional Components:

946-204

45o Elbow - 6-5/8" Black pipe and 4"

 

Aluminum Vent

946-205

Vinyl Siding Shield for Riser Vent

 

Terminal

946-208/P

Vent Guard

940

Square Wall Thimble Cover*

981Snorkel Termination (36")*

982Snorkel Termination (14")*

942

Wall Penetration

 

Heat Shield*

* Simpson Dura-Vent components

Alternate Snorkel

Termination Cap

Part # 982 (14")

Part # 981 (36")

HORIZONTAL TERMINATIONS

1)Set the unit in its desired location. Check to determine if wall studs are in the way when the venting system is attached. If this is the case, you may want to adjust the location of the unit.

2)Assemble the desired combination of pipe and elbow to the appliance adapter with pipe seams oriented down. Offset the pipe seams as double seams in one place will cause the outer pipe to take an oval shape. Kit comes complete with 18" of straight vent - 6-5/8" dia. black outer pipe and 4" dia. inner vent.

3)With the pipe attached to the stove, slide the stove into its correct location, and mark the wall for a 9-1/2"(insidedimensions)round hole.The center of the round hole should line up with the centerline of the horizontal pipe, as shown in diagram 1. Cut and frame the 9-1/2 round hole in the exterior wall where the vent will be terminated. If the wall being penetrated is constructed of non-combusti- ble material, i.e. masonry block or concrete, a 7" diameter hole is acceptable.

Diagram 1

Note:

a)The horizontal run of vent should have a 1/4 inch rise for every 1 foot of run towards the termination. Never allow the vent to run downward. This could cause high temperatures and may present the possibility of a fi re.

b)The location of the horizontal vent ter- mination on an exterior wall must meet all local and national building codes, and must not be blocked or obstructed. For External Vent Terminal Locations, see diagram in "Exterior Vent Terminal Locations" section.

c)Snorkel Terminations:

For installations requiring a vertical rise on the exterior of the building, 14-inch and 36-inch tall Snorkel Terminations as shown in Dia. 2 are available, as well as the standard Riser Vent. Follow the same installation procedures as used for standard Horizontal Termina- tion. NEVER install the snorkel upside down.

Diagram 2a

*Dia 2a & 2b: As specifi ed in CGA B149 Instal- lation Code. Local codes or regulations may require different clearances.

U37-1 Regency® ULTIMATE Rear Vent Direct Vent Freestanding Gas Stove

13

Image 13
Contents Ultimate U37 Rear Vent To the New Owner Information for MOBILE/MANUFACTURED Homes After First SaleTable of Contents Copy of Safety Label for U37 Safety LabelMA Code CO Detector RequirementsSpecifications InstallationGeneral Safety Information Important Message Save These InstructionsManufactured Mobile Home Additional Requirements Installation ChecklistClearances to Combustibles Locating Your GAS StoveExterior Vent Terminal Locations Safety Precautions For the Installer Venting Installation PrecautionsPlanning Your Venting Installation Description 6-5/8 Rigid Pipe Cross Reference Chart6-5/8 Rigid Pipe Cross Reference Chart Straight Vertical Terminations Using Rigid Piping SystemsOffset to Vertical Terminations Vent Restrictor PositionOptional Components Horizontal TerminationsAlternate Snorkel Termination Cap Snorkel TerminationsHint Apply sealant to female end Below Grade Snorkel InstallationRequired Parts Description Vertical Termination with CO-LINEAR Flex SystemAlternate Approved Caps General Approved for US Installations OnlyConverting a Factory Built Metal Chimney Converting Masonry Chimney Conversion Kit Contains Qty Conversion KIT# 514-969 from NG to LPGlow on logs LOG SET Installation Aeration AdjustmentGAS Connection High ElevationA02-65 Valve Description Door Installation GAS Pipe Pressure TestingPorts on the valve Optional Remote Control Louver InstallationWall Thermostat Final CheckAway from sharp edges Wiring DiagramOperating Instructions Lighting ProcedureOperating Instructions First FireBlower Thermodisc Copy of the Lighting Plate InstructionsPilot Flame Gas Control ValveMaintenance Glass Replacement Latch AdjustmentInstalling Glass Removing GlassRemoving Valve FAN MaintenanceReplacing Fan DC Sparker Battery Replacement Main Assembly Parts ListBurner & LOG Assembly Door Assemblies Page Conditions WarrantyInstaller Please complete the following information
Related manuals
Manual 36 pages 8.33 Kb

U37-LP1, U37-NG1 specifications

The Regency U37-NG1 and U37-LP1 are two innovative models that showcase advanced technology and superior engineering in the realm of HVAC (heating, ventilation, and air conditioning) systems. These units are designed to deliver optimal comfort while maximizing energy efficiency, making them ideal for both residential and commercial applications.

One of the standout features of the U37-NG1 is its use of a high-efficiency burner system, which ensures that every unit is capable of delivering substantial heating output while consuming minimal gas. This not only translates to lower utility bills for users but also aligns with sustainability goals by reducing carbon emissions. In terms of design, the U37-NG1 is compact and can be installed in a variety of settings, making it a versatile choice for many different environments.

The U37-LP1, on the other hand, is tailored for propane applications, making it perfect for areas where natural gas is inaccessible. It features a similar high-efficiency heating output, ensuring that it meets the demands of users without compromising on performance. The dual-fuel capability of the U37 series enhances its adaptability, allowing it to be used in a range of scenarios.

Both models are equipped with advanced control technologies, including programmable thermostats and smart connectivity features. Users can easily manage their heating systems through mobile apps, allowing for remote adjustments and real-time monitoring. This technology not only enhances user convenience but also promotes energy conservation by allowing users to adjust settings based on their lifestyle and preferences.

In terms of durability, the Regency U37 series boasts a robust construction designed to withstand various environmental conditions. With quality materials and expert craftsmanship, these units are built to last, reducing the need for frequent repairs or replacements.

Overall, the Regency U37-NG1 and U37-LP1 models combine cutting-edge technology with practical features to deliver an exceptional heating experience. Their commitment to energy efficiency, adaptability, and user-friendly controls positions them as leading options in the HVAC market, making comfortable living spaces more accessible while promoting environmentally responsible practices. Whether for home use or commercial properties, these systems offer reliability and performance tailored to the needs of modern users.