Regency P48-1 Installing the Optional FAN, To Remove the Fan, Shut the power off

Page 33

INSTALLATION

INSTALLING THE OPTIONAL FAN

120 Volt AC power is needed for the fan switch and blower. The fan can be hard wired if desired. The receptacle box should be installed on the left hand side of the unit by a qualified electrician. The neutral (wider) slot of the po- larized receptacle should be at the top.

Unit must be grounded at all times. Do not cut the ground terminal off under any circumstances.

9)Attach the two control boxes to the bottom louver and tighten the 2 screws on the left side and 2 screws on the right side.

1)Shut the power off.

2)Remove the standard flush door and the optional bay door, if installed. Open the bottom louver door.

3)Remove the 2 screws holding the Burner ON/OFF switch and bracket to the bottom louver and lift the assembly out.

4)Turn the fan base on its side (with the base facing towards you) and then slide the fan in towards the rear of the unit. Turn the fan upright and slip it over the two mounting studs. Take care not to damage the insula- tion on the fan base. Ensure that the fan blades do not rub against the valve tubing. Diagram 1.

5)Connect fan ground cable to ground lug. Refer to wiring diagram.

6)Slide the thermodisc/cover assembly into the bracket clip on the underside of the firebox. Check that no wire will touch the hot surfaces. Diagram 2.

7)Attach the Fan control box to the Burner ON/ OFF control box. Diagram 3.

Diagram 1

Diagram 2

Diagram 3: Use the clip & hook on the side of the control boxes to join them together.

8)Secure the two boxes together with one screw.

Secure the 2 boxes together

with one screw.

Secure left side with 2 screws.

Secure right side with 2 screws.

10)Secure the fan wires and power cord by attaching one of the adhesive backed wire holder clips (Part #910-199) onto the stove base. Use the second clip to bundle up the wires approximately 4" from the control box. Ensure that there is no interference with the wires when the louver is closed and that no wire will touch the hot metal surfaces or sharp edges.

11)Plug the fan power cord into the rear end of the receptacle box to provide the maximum clearance from the louvers.

To Remove the Fan

1)Shut the power off.

2)Reverse the above instructions.

NOTE: The bearings are lubricated for life. Do not lubricate them. Make sure you vacuum the fan area on a regular basis.

IMPORTANT:

These fans collect a lot of dust from within your home. Ensure you maintain these fan motors on a regular basis by vacuuming out the fan blades and hous- ing using a soft brush nozzle.

Regency P48-1 Zero Clearance Direct Vent Gas Fireplace

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents P48-1 Gas Fireplace To the New Owner Manufactured Mobile Home RequirementsTable of Contents Copy of Safety Decal for P48-NG1 and P48-LP1 Safety LabelGeneral Safety Information InstallationInstallation Checklist Save These InstructionsManufactured Mobile Home Additional Requirements Unit Specifications Locating Your GAS StoveOptional Duct System Optional Heat ReleaseMantel ClearancesCeiling Max. Depth 36 914mmMantel LEG Clearances MantelsFraming & Finishing Top Standoff Assembly Unit Assembly Prior to InstallationVenting Introduction Top Facing Support Side Nailing StripsExterior Vent Termination Regency Direct Vent System Flex Horizontal Terminations Only VentingSimpson DURA-VENT Venting Components List Simpson DURA-VENT VentingDescription Parts not supplied by Dura-VentRegency Direct Vent System Flex Venting Arrangements Horizontal TerminationsHorizontal Venting with Three 3 90o Elbows Horizontal Venting with Two 2 90o ElbowsMin Max Min Max Min Max Vertical Venting with Two 2 90o ElbowsOption + H1 V + Vertical Venting with Three 3 90o ElbowsSimpson DURA-VENT Direct Vent GS System Venting Arrangements Vertical TerminationsInstallation Horizontal Installations Vertical Termination Offset ChartFor Regency Direct Vent System Flex Installation ProceduresPilot Adjustment GAS Line InstallationGAS Pipe Pressure Testing High ElevationBottom Clips Brick Panels Installation02-88 02-90 02-87 02-89 02-86 02-85 02-84 02-83 LOG SET Installation02-88 02-83 02-86 02-85 02-89 02-84 02-8902-90 02-8602-84 02-87 02-88 02-8502-83Standard Flush Door Flush LouversNot under the gas line Optional BAY Door BAY LouversOptional Bay Trim Double Screen Door Optional Finishing TrimThermostat Wire Table Option Remote ControlDo not cut the ground terminal off under any circumstances Wiring DiagramInstalling the Optional FAN Shut the power offTo Remove the Fan Conversion Kit Contains Operating Instructions Copy of the Lighting Plate Instructions Normal Operating Sounds GAS AppliancesMaintenance Installing Valve Bay Glass ReplacementDoor Glass Shut off the gas supply Removing ValveP48-1 Main Assembly Parts List102 100 P48-1 Burner & LOG Assembly P48-1 Flush Door & Louvers P48-1 BAY Front & Louvers Regency P48-1 Zero Clearance Direct Vent Gas Fireplace Regency P48-1 Zero Clearance Direct Vent Gas Fireplace Conditions WarrantyInstaller Please complete the following information

P48-1 specifications

The Regency P48-1 is a prominent model in the realm of modern communication technology, particularly recognized for its innovative features and robust performance. Originally launched as part of a series targeting both casual and professional users, the P48-1 stands out through its unique integration of advanced functionalities and user-friendly design.

One of the main features of the Regency P48-1 is its seamless connectivity capabilities. It supports various communication protocols, including Wi-Fi, Bluetooth, and cellular networks, allowing users to maintain reliable connections irrespective of their location. This versatility makes it an ideal choice for individuals who prioritize mobility without sacrificing functionality.

The device is equipped with a high-resolution display that enhances user experience, whether for browsing, video calls, or multimedia content consumption. The touch interface is responsive and intuitive, contributing to easy navigation through different applications and settings. The display’s vivid colors and sharp contrasts make it suitable for extended use, reducing eye strain during prolonged sessions.

At the heart of the Regency P48-1 is its state-of-the-art processing unit, which ensures fast and efficient performance. This technology allows for multitasking capabilities, enabling users to run multiple applications simultaneously without encountering lags. Coupled with significant internal storage and expandable memory options, the device caters to users who require ample space for their data, applications, and media files.

The P48-1 also incorporates advanced battery management technologies, providing extended usage time on a single charge. Users can enjoy the device's capabilities throughout the day without frequent interruptions for recharging. The battery's longevity, combined with fast-charging features, ensures that users remain connected and productive.

Security is a top priority in the design of the Regency P48-1. It includes biometric authentication methods such as fingerprint scanning and facial recognition, offering users peace of mind regarding their private information. Coupled with regular software updates, these features enhance the device's resilience against cybersecurity threats.

In conclusion, the Regency P48-1 embodies a blend of functionality, performance, and user-centric design. Its advanced communication features, high-resolution display, powerful processing capabilities, and robust security measures make it an exemplary device for a wide array of users, from professionals to tech enthusiasts. As technology continues to evolve, the P48-1 serves as a benchmark for what modern communication devices can achieve.
Top Page Image Contents