Regency E21-LP2, E21-NG2 Offset Flue Adaptor, Venting, GAS Pipe Pressure Testing

Page 12

INSTALLATION

OFFSET FLUE

ADAPTOR

A Offset Flue Adaptor Kit, Part #532-920 is available as an accessory to move the fl ue outlet back for easier liner installations in deep fi replaces.

VENTING

THE APPLIANCE MUST NOT BE CONNECTED TO A CHIMNEY FLUE SERVING A SEPARATE SOLID FUEL BURNING APPLIANCE.

This appliance is designed to attach to a 4" diameter type B-Vent or double thickness approved aluminium fl ex liner.

The fl ue collar of the appliance will fi t inside a standard vent and may be fastened directly to the vent by sheet metal screw or a B-Vent, single wall vent connector.

B-Vent chimneys require a 1" clearance to combustibles.

A3"diametertypeB-Ventorapprovedaluminium

ex liner may also be used with a 4" to 3" reduc- ing adapter. Consult venting charts and local code requirements.

The Regency® Insert incorporates its own internal draft hood, so no additional external draft hood is required. Check periodically that the vent is unrestricted and an adequate draft is present when the unit is in operation.

Before installing the vent system ensure that the damper plate is locked into the open position and secure to prevent the damper plate from falling down and crushing the liner.

The appliance is equipped with a vent safety shutoff system and a safety control system designed to protect against improper venting of combustion products. The appliance will not function without being connected to a proper system.

WARNING: Operation of this heater when not connected to a properly installed and maintained venting system or tampering with the vent shut-offsystemcanresultincarbon monoxide (CO) poisoning and possible death.

This appliance must not be connected to a chimney fl ue serving a separate solid fuel burn- ing appliance.

For best venting performance, we recommend the following venting rules:

1)Use only certifi ed Type B gas vent or approved fl ex liner.

2)Follow the vent manufacturer's instructions and clearance requirements.

3)Observe any local code restrictions, if any, regarding the installation of gas inserts.

4)Use as few elbows as possible.

5)Keep horizontal lengths as short as possible and maintain at least an upward slope of 1/4 in. (6.4mm) for every 12 in. (305mm) of horizontal run.

6)Terminate the vent with a suitable certifi ed vent cap.

COMBUSTION AND VENTILATION AIR

WARNING: This appliance needs fresh air for safe operation and must be installed with provisions for adequate combustion and ventilation air available to the room in which it is to be operating.

Follow CAN/CGA B149 (in Canada) or ANSI Z223.1 (in the USA) requirements, and any local codes or regulations of the enforcing authority.

Air for combustion is drawn in through the front of the unit, therefore, the front of the unit must be kept clear of any obstructions.

GAS PIPE

PRESSURE TESTING

The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig. (3.45 kPa). Disconnect piping from valve at pressures over 1/2 psig.

Themanifoldpressureiscontrolledbyaregulator built into the gas control, and should be checked at the pressure test point.

Note: To properly check gas pressure, both inlet and manifold pressures should be checked using the valve pressure ports on the valve.

1)Make sure the valve is in the "OFF" position.

2)Loosen the "IN" and/or "OUT" pressure tap(s), turning counterclockwise with a 1/8" wide fl at screwdriver.

3)Attach manometer to "IN" and/or "OUT" pressure tap(s) using a 5/16" ID hose.

4)Light the pilot and turn the valve to "ON" position. Read manometer.

5)The pressure check should be carried out with the unit burning and the setting should be within the limits specifi ed on the safety label.

6)When fi nished reading manometer, turn off the gas valve, disconnect the hose and tighten the screw (clockwise) with a 1/8" fl at screwdriver. Note: Screw should be snug, but do not over tighten

12

Regency® E21-2 Gas Fireplace Insert

Image 12
Contents E21 Gas Insert Congratulations Table of Contents Safety Label Duplicate Serial NoRequirements MA Code CO DetectorInstallation General Safety InformationImportant Message Save These Instructions Before YOU StartInstallation Checklist Minimum Fireplace ClearancesPolicy for Solid Fuel Burning & Factory Built Fireplaces Clearances to Combustibles Combustible boardGAS Connection High ElevationWiring Diagrams Lug DetailFlue Connector Installation For Propane Units and Units Equipped with DC Spark BoxesGAS Pipe Pressure Testing Offset Flue AdaptorVenting Combustion and Ventilation AIRValve Description GAS Insert AerationsystemTest for Flue Spillage Optional Brick PanelLOG SET Installation Faceplate & Trim InstallationFlush Glass Use of substitute glass will Void all product warrantiesFlush Louvers Optional BAY Front BAY LouversConversion Kit# 534-969 from NG to LP Installation of the DC Sparker Chain Full Screen Doors Hinge Remote Control Wall Switch Wall ThermostatOperating Instructions Copy of Lighting Plate Instructions Maintenance Door Glass Replacement Removing Valve AssemblyDisconnect the power Removing the FANParts List DescriptionBurner Assembly & LOG SET Bay Door Flush Door DescriptionFaceplate Assembly Warranty ConditionsInstaller Please complete the following information

E21-NG2, E21-LP2 specifications

The Regency E21-LP2 and E21-NG2 are modern gas fireplaces that embody style, efficiency, and advanced engineering, making them standout choices for homeowners seeking both aesthetic appeal and functional utility. These models are designed to complement a wide variety of interior decor styles while providing warmth and comfort.

One of the most prominent features of the E21 series is its high-efficiency heating capability, which allows these fireplaces to generate a significant amount of heat while using minimal fuel. The E21-LP2, designed for liquid propane, and the E21-NG2, designed for natural gas, ensure versatile installation options for different home setups. Homeowners can select the fuel type that best suits their needs or local availability.

The design of the Regency E21 models is marked by a large viewing area, providing an unobstructed view of the mesmerizing flames. The impressive flame pattern not only adds to the ambiance but also creates a warm and inviting focal point in any living space. The elegant, clean lines and contemporary frame enhance the fireplace's visual appeal, making it an excellent choice for modern interiors.

In terms of technology, both models are equipped with the advanced IntelliFire ignition system, which offers reliability and ease of use. This system ensures that igniting the fireplace is straightforward and safe, freeing homeowners from the hassles of traditional methods. Furthermore, the built-in programmable thermostat allows for precise temperature control, ensuring optimal comfort levels with minimal environmental impact.

Moreover, the Regency E21 series is constructed with high-quality materials designed to offer durability and longevity. The fireplaces come with a variety of finish options, allowing homeowners to personalize their units to match their specific tastes and styles. The E21 models also feature a convenient glass safety barrier, which enhances safety while maintaining the fireplace's aesthetic appeal.

With an emphasis on energy efficiency and environmental responsibility, the E21-LP2 and E21-NG2 are not only stylish additions to any home but also economically favorable choices for homeowners. By combining practical features with contemporary design, Regency has created fireplaces that cater to modern living while providing comfort and elegance. Whether for new installations or upgrades to existing spaces, these models are sure to impress.