Regency E21-LP2, E21-NG2 installation manual Installation of the DC Sparker

Page 18

INSTALLATION

14)Check that the screw is clean and if necessary remove dirt.

15)Flip the screw (Fig. 3).

Fig.3

16)Using the Allen wrench as shown in Fig.4, rotate the screw clockwise until snug, do not overtighten.

Fig.4

WARNING!

Do not overtighten the screw. Recommended to

grip the wrench by the short side.

WARNING!

Also check that the pilot and main

burner injectors

are appropriate for the gas type.

19)Replace Burner Tray and reverse steps 6) to 1).

20)Adjust the burner aeration setting from 1/8" to 3/16" as required for the best fl ame picture.

21)Remove the switch cover from the left side of the body base and pull the thermodisc out of the bracket under the left side of the fi rebox bottom and replace with the Thermodisc supplied with this kit.

25)Remove the Piezo Ignitor by unscrewing the nut at the back of the mounting bracket.

Ignitor

Wire

Piezo

Ignitor

26)Disconnect the ignitor wire from the Piezo Ignitor and connect it to the DC Sparker.

DC

Sparker

Ignitor

Wire

27)Install the 3/4" nylon plug to cover up the hole on the mounting bracket.

17)Verify that if the conversion is from NG to LPG, the screw must be re-assembled with the red o-ring visible (Fig. 5).

Remove the 2 nuts holding the switch box in

place, then pull the

thermosdisc out of the bracket.

Red o-ring visible

Fig.5

LPG Configuration

22)Attach the label "This unit has been converted to LPG" near or on top of the serial # decal.

23)Replace the yellow "NG" label with red "LPG" label.

28)Connect the DC spark generator wires to the SIT Valve with the screw, which is provided in the kit.

18)Re-assemble the black protection cap (Fig. 6).

Fig. 6

Installation of the DC Sparker:

24)Locate the Piezo Ignitor situated at the side of valve.

Piezo

Ignitor

18

Regency® E21-2 Gas Fireplace Insert

Page 17 Page 19
Image 18
Page 17 Page 19
Contents E21 Gas Insert Congratulations Table of Contents Safety Label Duplicate Serial NoRequirements MA Code CO DetectorImportant Message Save These Instructions InstallationGeneral Safety Information Before YOU StartInstallation Checklist Minimum Fireplace ClearancesPolicy for Solid Fuel Burning & Factory Built Fireplaces Clearances to Combustibles Combustible boardGAS Connection High ElevationWiring Diagrams Lug DetailFlue Connector Installation For Propane Units and Units Equipped with DC Spark BoxesVenting GAS Pipe Pressure TestingOffset Flue Adaptor Combustion and Ventilation AIRTest for Flue Spillage Valve DescriptionGAS Insert Aerationsystem Optional Brick PanelLOG SET Installation Faceplate & Trim InstallationFlush Glass Use of substitute glass will Void all product warrantiesFlush Louvers Optional BAY Front BAY LouversConversion Kit# 534-969 from NG to LP Installation of the DC Sparker Chain Full Screen Doors Hinge Remote Control Wall Switch Wall ThermostatOperating Instructions Copy of Lighting Plate Instructions Maintenance Disconnect the power Door Glass ReplacementRemoving Valve Assembly Removing the FANParts List DescriptionBurner Assembly & LOG SET Bay Door Flush Door DescriptionFaceplate Assembly Warranty ConditionsInstaller Please complete the following information

E21-NG2, E21-LP2 specifications

The Regency E21-LP2 and E21-NG2 are modern gas fireplaces that embody style, efficiency, and advanced engineering, making them standout choices for homeowners seeking both aesthetic appeal and functional utility. These models are designed to complement a wide variety of interior decor styles while providing warmth and comfort.

One of the most prominent features of the E21 series is its high-efficiency heating capability, which allows these fireplaces to generate a significant amount of heat while using minimal fuel. The E21-LP2, designed for liquid propane, and the E21-NG2, designed for natural gas, ensure versatile installation options for different home setups. Homeowners can select the fuel type that best suits their needs or local availability.

The design of the Regency E21 models is marked by a large viewing area, providing an unobstructed view of the mesmerizing flames. The impressive flame pattern not only adds to the ambiance but also creates a warm and inviting focal point in any living space. The elegant, clean lines and contemporary frame enhance the fireplace's visual appeal, making it an excellent choice for modern interiors.

In terms of technology, both models are equipped with the advanced IntelliFire ignition system, which offers reliability and ease of use. This system ensures that igniting the fireplace is straightforward and safe, freeing homeowners from the hassles of traditional methods. Furthermore, the built-in programmable thermostat allows for precise temperature control, ensuring optimal comfort levels with minimal environmental impact.

Moreover, the Regency E21 series is constructed with high-quality materials designed to offer durability and longevity. The fireplaces come with a variety of finish options, allowing homeowners to personalize their units to match their specific tastes and styles. The E21 models also feature a convenient glass safety barrier, which enhances safety while maintaining the fireplace's aesthetic appeal.

With an emphasis on energy efficiency and environmental responsibility, the E21-LP2 and E21-NG2 are not only stylish additions to any home but also economically favorable choices for homeowners. By combining practical features with contemporary design, Regency has created fireplaces that cater to modern living while providing comfort and elegance. Whether for new installations or upgrades to existing spaces, these models are sure to impress.
Top Page Image Contents