Check monthly | Weil-McLain CGa specs

CGa,CGi,CGs,EG,EGH,LGB,PEG,PFGBoilers

❏Check daily . . . . . . . . . . . . . . . . .

Pressure/temperature gauge or pressure gauge (steam)

1.Water boilers — Make sure the pressure reading on the boiler pressure/temperature gauge does not exceed 24 psig. Higher pressure may indicate a problem with the expansion tank or gauge.

2.Steam boilers — Make sure the pressure reading on the boiler pressure gauge does not exceed 15 psig. Higher pressure indicates a problem with the gauge or limit control.

3.Contact a qualified service technician if problem persists.

Air openings

1.Verify that combustion and ventilation air openings to the boiler room and/or building are open and unobstructed.

2.CGs boilers — Verify that boiler vent discharge and air intake are clean and free of obstructions. Remove any debris on the air intake or flue exhaust openings.

❏Check monthly . . . . . . . . . . . . . . . .

Boiler piping

1.Visually inspect for leaks around piping, circulators, relief valve and other fittings. Immediately call a qualified service technician to repair any leaks.

Have leaks fixed at once by a qualified service technician. Continual fresh makeup water will reduce boiler life. Minerals can build up in sections, reducing heat transfer, overheating cast iron, and causing section failure.

Do not use petroleum-based cleaning or sealing compounds in boiler system. Severe damage to boiler and system components can occur, resulting in possible severe personal injury, death or substantial property damage.

Venting system

Failure to inspect the vent system as noted above and have them repaired by a qualified service technician can result in vent system failure, causing severe personal injury or death.

1.Visually inspect all parts or the flue gas venting system for any signs of blockage, leakage or joints or deterioration of the piping.

2.CGa and EG boilers:

If flame blows out or flickers severely, the vent system must be checked for obstructions or other causes of improper venting.

b.Verify the vent damper (CGa and EG boilers) opens before burners ignite.

3.Notify your qualified service technician at once if you find any problem.

Boiler relief valve . . . . . . . . .

1.Inspect the boiler relief valve (see Figure 3) and the relief valve discharge pipe for signs of weeping or leakage.

2.If the relief valve often weeps:

•water boilers — the expansion tank may not be working properly.

•steam boilers — limit control may be set too high or there may be system problems.

•Immediately contact your qualified service technician to inspect the boiler and system.

Figure 3 Relief valve

a.With boiler firing, hold a candle or match be- low lower edge of draft hood “skirt.” If flame

does not blow out, but burns undisturbed, the
vent system is working properly.	59203

8	Part Number 550-110-592/1099

CGa specifications

The Weil-McLain CGa is a highly efficient and reliable gas-fired boiler that has established itself as a favorite among homeowners and HVAC professionals alike. Known for its impressive performance and durability, the CGa series is designed to deliver comfort while optimizing energy consumption.

One of the main features of the Weil-McLain CGa is its efficiency. With an AFUE (Annual Fuel Utilization Efficiency) rating of up to 84%, this boiler efficiently converts gas into heat, ensuring minimal energy waste. This efficiency not only translates to cost savings on energy bills but also supports environmental sustainability through reduced emissions.

The CGa boilers are designed for versatility, capable of being used in various applications, including residential heating systems and light commercial settings. With a range of models available, the CGa can meet different heating demands, ensuring consistent comfort regardless of the building size or layout.

The boiler's built-in heating capabilities include the option for either hot water or steam heating, adding to its versatility. Weil-McLain offers multiple BTU outputs across the CGa series, allowing for a customized solution based on specific heating requirements.

State-of-the-art technologies are evident in the CGa's design. The integrated hot surface ignition system enhances start-up reliability, minimizing the risk of combustion issues and ensuring safe operation. Additionally, the unit features a standard draft diverter for efficient venting, allowing for optimal exhaust management within the heating system.

Durability is another key characteristic of the Weil-McLain CGa. Constructed from high-quality materials, these boilers are engineered to withstand the rigors of daily operation. The cast iron heat exchanger provides superior heat retention and longevity, ensuring that the system remains operational for years with proper maintenance.

Installation of the CGa boiler is straightforward due to its compact design and versatile venting options, which can accommodate various installation configurations. This ease of installation combined with a user-friendly interface allows homeowners and technicians alike to manage the system with minimal hassle.

In summary, the Weil-McLain CGa boiler epitomizes efficiency, durability, and versatility. Its advanced technologies and robust construction make it a top choice for those seeking a reliable heating solution for their homes or commercial spaces. With Weil-McLain's commitment to quality and innovation, the CGa series delivers performance that meets the diverse needs of today's heating applications.