Pella 818K0100 installation instructions Optional Sill Pan Instructions, O O R S

L D O O R S

Optional Sill Pan Instructions.

I.Cut the sill pan to the width of the rough opening plus 2".

Note: The 2" added onto the rough opening width is for a 1" bend on each end.

J.Make a 1" cut in each fold at both ends of the sill pan.

Note: These cuts will allow the edges of the sill pan to be bent.

Note: 4-5/8" wide for Out-swing and In-swing for 4-9/16" wall condition. For other wall conditions; measure wall depth and add 1/16".

D O O R S • A L

K.Cut 1" off each end of the interior sill pan lip.

1"	1J
Variable

1K(

INTERIOR SILL	PAN LIP
EXTERIOR SILL
PAN LIP
	1"
	*/5&3*03 4*--
	1"/ -*1

1"

D O O R S • A L L D O O R S • A L L

L. Bend each end of the center	1L)
panel up.

M.Install the sill pan by sliding into place until the exterior sill pan lip is flush with the exterior of the rough opening.

N.Apply sill flashing tape. Cut a piece of flashing tape 2" longer than the opening width. Apply at the bottom of the opening, covering the exterior sill pan lip as shown.

Note: If applicable, apply spray adhesive to building felt prior to applying the flashing tape.

&95&3*03 4*--
					1"/ -*1
					*/5&3*03 4*--
					1"/ -*1
				&95&3*03 4*--
					1"/ -*1
1M
EXTERIOR			SILL
Install	flush			PAN	LIP
against		exterior
rough
	opening.
		N
1N
EXTERIOR
			SILL
				PAN
Flashing					LIP
Weather				Tape
		Barrier

Exterior

D O O R S • A L L

O. Cut two 9" pieces of flashing tape with a 1" x 3"

tab at the bottom, on opposite corners as shown.

P.Apply the tabbed 9" pieces of flashing tape. The tape is applied so 2" will cover the inside of the rough opening and lap over the side flange of the sill pan. The 1" x 3" tab laps over the bottom flashing tape as shown.

3"3"

1O

9" 9"

2" 3" 2"

1" Tabs 1" Tabs

O O R S • A L L

Q.Cut two 6" pieces of flashing tape and apply to each side of the rough opening, overlapping the first piece by 1" and lapping the bottom over the side flange of the sill pan as shown.

			-
			1P
			4JEF
			'MBOHF
	
		&95&3*03 4*--
			1"/ -*1
			'MBTIJOH 5BQF

.

1Q



&95&3*03
4*--

1"/
-*1

'MBTIJOH
5BQF

• A L L D

R.Cut a piece of flashing tape to the width of the opening. Install to the flanges of the sill pan and overlap the tape from step 1N by 1”. If needed add a second or third piece of flashing tape until the sill pan is covered to the interior sill pan lip.

Note: The purpose of this tape is to seal the sill screws when installing the door.

D O O R S

S.Cut two pieces of flashing tape 1-1/2" x 6" and apply to the bottom corners of the opening by beginning in the corner of the sill pan, with 3/4" of the tape applied to the sill pan and 3/4" of the tape applied to the side flange. The remainder of the tape is to be at a 45 degree angle onto the exterior.

1S

1R

SILL

PAN

LIP

1"