Cooler Installation, Operation | Essick Air CP70 specification

Cooler Installation

Install Pedestal and Casters

Unpack the unit and remove the media frame to access the pedestal and 4 cast- ers. See the maintenance section for instructions on removing media frame. CAUTION: Do not damage hose connecting pump to media frame. Cut the cable ties holding pedestal to frame of unit and remove pedestal. Remove the casters from the underside of the pedestal. To install the pedestal, turn the unit on it’s side. Line up the bosses on the pedestal to the bosses on the base of the unit (see ﬁg. 1). Use the four provided screws to attach the pedestal

to the base of unit. Press the stem casters into each corner hole of pedestal, installing the 2 locking casters on the front and the 2 non-locking on the back side.

Base Pedestal Caster

Screw

Fig. 1

Operation

Fill With Water

To ﬁll this unit with water, open the water ﬁll door and ﬁll with a pitcher or water hose (see ﬁg. 2). Do Not Overﬁll. CAUTION:

Take care when moving unit ﬁlled with water, spillage may occur. Unlock casters when moving. Do not tip unit.

Water Level Indicator

On the front of the unit there is an access window to view the level of the water (see ﬁg. 2). When the unit is full of water, the level indicator will be at the top of the window and as the level of the water is decreased in the unit, the indicator will lower.

Water

Water Level Fill

Indicator Door

Refer to the control panel in ﬁgure 3 for the following instructions.

Fig. 2

Turning On Unit

Once the unit is plugged in, pressing the “Power” button will light up the backlight on the display and start the unit in Fan-High mode. The pump will not start until the “Pump” button is pressed. The display will remain backlit for 2 minutes after the last button on the control is pushed.

Pump / Cooler Operation

To operate this unit as an evaporative cooler, the unit must be ﬁlled with water and the pump powered on. Press the “Pump” button to turn on the pump. The water drop indicator on the display will ﬂash while the pump is on. To operate the unit as a fan only, press “Pump” to turn off the pump.

Note: The pump will not run if the water level falls below a certain level. When the water level drops below this level, an audible alarm will sound and the “Low Water” indicator on the display will ﬂash on and off. The audible alarm will stop after 60 seconds or when the “Pump” button is pushed. The indica- tor will remain ﬂashing until the unit is ﬁlled with water. You will need to restart the pump by pressing “Pump” after the unit is reﬁlled with water.

Fan Operation

Pressing the “Speed” button on the control will cycle the fan speed from High to Mid to Low. The speed setting will be highlighted in the display.

FAN	PUMP
HIGH
MID
LOW	LOW WATER
COOL	VENT

Oscillate Mode

Pressing the “Oscillate” button will oscillate the vertical vanes back and forth, distributing the air side to side. The “Oscillate” indicator on the display will be displayed when on. Press the button again to turn off.

Timer Mode

OSCILLATE	TIMER

Timer	Oscillate	Power	Speed	Pump
	Oscillate		Speed

Fig. 3

This unit is equipped with a timer. You may set the time interval for the unit to stay on. Pressing the “Timer” button will set the time interval in 1/2 hour increments up to 8 hours. The display will ﬂash while setting the time and will display constantly once it is set. The display will count down the time remaining in 1/2 hour increments. When the time interval is reached, the unit will turn off.

CP70 specifications

The Essick Air CP70 is a remarkable evaporative cooler designed to provide enhanced comfort in various indoor environments. This unit is known for its energy efficiency and ability to deliver cool, refreshing air during hot weather. With its sleek design, the CP70 not only looks good in any space but also offers an array of features and technologies that set it apart from traditional cooling systems.

One of the standout features of the Essick Air CP70 is its impressive cooling capacity. It is equipped with a powerful fan that can circulate air throughout larger areas, making it an ideal choice for both residential and commercial use. The evaporative technology used in this cooler relies on the natural process of evaporation to lower the air temperature, making it an eco-friendly option compared to conventional air conditioning units that consume a significant amount of energy.

The CP70 also incorporates a large water reservoir that allows for extended use without frequent refills. This feature is particularly beneficial for those in hotter climates, ensuring that the unit can operate for extended periods while consistently delivering cool air. Furthermore, the cooler is designed with a built-in water level indicator, allowing users to easily monitor the water status and prevent any operational hiccups.

In terms of convenience, the Essick Air CP70 is outfitted with user-friendly controls, including an adjustable thermostat and multiple fan speed settings. These options allow users to personalize the cooling experience to fit their preferences, ensuring optimal comfort. Additionally, the unit’s lightweight design and integrated caster wheels make it easy to move from room to room, providing flexibility in cooling various spaces.

A notable aspect of the CP70 is its low maintenance requirements. The cooling pads are designed for durability and can be easily replaced, ensuring the unit operates efficiently for years to come. The easy-access water fill door also simplifies the refill process, enhancing user experience and convenience.

Overall, the Essick Air CP70 is a top-tier evaporative cooler that combines efficiency, convenience, and user-friendly features. It offers an eco-friendly cooling alternative without sacrificing performance, making it an excellent choice for anyone seeking relief from heat.