Integra DTR-5.1 appendix Erasing a learned code from a Mode button, Mode buttons, Ent

Page 35

Programming the remote controller codes of other devices into the RC-424M

See page 39 for information on how to erase the learned codes from all buttons.

SEND/LEARN indicator

MODE buttons

ENT

HOME THEATER CONTROLLER

RC-424M

Erasing a learned code

You can erase a learned code. You cannot erase pre- set codes.

•Erasing a code programmed in a button

1.Press and hold down the corresponding MODE button and press the ENT button, then release the buttons. When you press the MODE button, the SEND/LEARN indicator lights up. When you press the ENT button, the indicator turns off. When you release the buttons, the indicator lights up again.

2.Press and release the button from which you wish to erase the learned code.

When you press the button, the SEND/LEARN indica- tor turns off. When you release the button, the indica- tor lights up again.

3.Press and release the same button again.

The SEND/LEARN indicator ﬂashes twice slowly. The learned code is erased.

Note:

•If you do not press the button in step 2 or 3 for more than 30 seconds, the SEND/LEARN indicator ﬂashes three times quickly, then the RC-424M exits Learning mode. Resume Step 1.

SEND/LEARN indicator

MODE buttons

ENT

HOME THEATER CONTROLLER

RC-424M

Erasing a learned code from a MODE button

1.Press and hold down the MODE button from which you wish to erase the learned code, and press the ENT button twice. Then release the buttons.

When you press the MODE button, the SEND/LEARN indicator lights up. When you press the ENT button, the indicator turns off. When you release the buttons, the indicator ﬂashes twice slowly, then lights up again.

2.Press and release the same MODE button again. When you release the button, the SEND/LEARN indi- cator ﬂashes twice slowly. The learned code is erased.

Note:

•If you do not press any button for more than 30 sec- onds, the SEND/LEARN indicator ﬂashes three times quickly, then the RC-424M exits Learning mode. Resume Step 1.

•If you make a mistake during programming, the SEND/LEARN indicator ﬂashes three times quickly, the RC-424M exits Learning mode. Resume Step 1.

•If have programmed many button operations to a single MODE button, the SEND/LEARN indicator may remain illuminated continuously in Step 2. This is not malfunction.

35

Image 35

Contents DTR-5.1 Important Safeguards Modele pour les Canadien PrecautionsFor U.S. model For Canadian modelSupplied accessories FeaturesBefore operating this unit Installing the remote controller batteriesUsing the remote controller Audio equipment connections Signal flowDigital audio connections Video equipment connectionsDecoder with 5.1 channel output Connecting other devicesAC outlet connection Connecting other devicesConnecting a power cable Connections for remote controlCenter Speaker Connecting speakersFront Speakers Surround SpeakersPositioning speakers Connecting the powerAssembling the AM loop antenna Connecting the antenna cableConnecting the included antennas Making antenna connectionsDirectional Iinkage Connecting an FM outdoor antennaConnecting an AM outdoor antenna Making antenna connectionsConfig Setup Speaker setupSetting the Config parameters Distance Setup Speaker setupSetting the Distance parameters Test button Level +/- buttons Using the Test Tone function on the main unitMode Audio button CH SEL button VOL q/u buttons Test ToneDVD Selecting a sound sourceSelecting a sound source Selecting the input signal formatPower on Volume When Multi channel input is selected as a sourceUsing the Power On Volume function Sleep function Remote controller only Adjusting the tone Bass, TrebleListening through headphones Phones About volume VolumeStereo System with L/R front and center speakersSystem with L/R front speakers Dolby 3 StereoUsing Listening Mode Using Listening ModeLate Night Setting the Listening mode parametersLate Night Front Effect Re-EQ LFE level controlDisplay button Tuning in a radio stationManual tuning Listening to a stereo radio station FM modeTUN Using preset radio stationsMode Audio Programming radio stationsCancelling preset stations Using preset radio stationsSelecting a preset station Recording a source Adding new sound to a video tape during video editing Recording a sourceVideo 2, Video Tape VCR Video Connections in the Sub-room Enjoying Music and Movies in the Sub-roomOutline of Multi-room Remote System Speakers A/B Enjoying Music and Movies in the Sub-roomVOL Using the remote controllerControlling the DTR-5.1 Audio Display DVD Using the remote controller Controlling an Integra/Onkyo CD player Controlling an Integra/Onkyo DVD playerControlling an Integra/Onkyo MD recorder Mode SAT, CABLE, VCR, and TV buttonsMode AUDIO/TAPE Mode SAT CABLE, VCRProgramming procedure ENT Erasing a learned code from a Mode buttonMode buttons Erasing a learned codeProgramming Macro mode Using a Macro functionWhat is a Macro function? Programming Macro Direct Using a Macro functionUsing a Macro function Erasing all codes and operations programmed in the buttons REO Troubleshooting guideEiaj Remote Control12 13 14 Control positions and namesDisplay Front panelControl positions and names Onkyo U.S.A. Corporation