Integra DTR-5.1 appendix Using a Macro function, What is a Macro function?, Programming Macro mode

Page 36

Using a Macro function

What is a Macro function?

A Macro function enables you to program a series of button operations on the remote controller into a single button. For example, you need to follow the steps below to play a CD player connected to the DTR-5.1 without using the Macro function:

1:Press the MODE AUDIO button.→ 2: Press the ON button. → 3: Press the CD (INPUT SELECTOR) button.→ 4: Press the MODE CD button. → 5: Use the numeric keys to select the desired song.

This operation will be two button presses away if you program these steps into a macro button.

2

1, 2 1, 3 2

2

2

HOME THEATER CONTROLLER

RC-424M

Tip:

The codes programmed into a MACRO but- ton will be transmitted with an interval of 0.5 seconds. However, some devices may not be able to complete one operation in 0.5 sec- onds and may miss the next code. In this case, press one operation button, press the corresponding MODE button, then press another operation button to extend the inter- val between the two operations up to one second.

Programming Macro mode

You may program the desired steps into each of eight MODE buttons. The following example explains how to program Steps 1–5 (described above) into the MACRO MODE button under the MODE CD button (CD mode).

1.Press and hold down the desired MODE button you wish to program (in this case, MODE CD button), and press the MACRO MODE button. Then release the but- tons.

When you press the MODE CD button, the SEND/ LEARN indicator lights up. When you press the MACRO MODE button, the indicator turns off.

When you release the buttons, the indicator flashes briefly, then lights up again.

2.Press the operation buttons in series you wish to pro- gram into the MACRO MODE button.

Press the MODE AUDIO, ON, CD (INPUT SELECTOR), MODE CD buttons, and a numeric key. When you press the button, the SEND/LEARN indicator turns off. When you release the button, the indicator lights up.

3.Press the MACRO MODE button to complete pro- gramming.

The SEND/LEARN indicator flashes twice slowly. Repeat Steps 1–3 to program other series of button operations into another MODE button.

4.Check to see if the series of button operation has been correctly learned.

Point the remote controller toward the DTR-5.1, press the MODE CD button, and press the MACRO MODE button to see if the unit responds as programmed.

Transmitting the codes in Macro mode takes a while. During transmission, point the remote controller toward the device to be controlled.

Note:

•You may program up to 16 button operations into each MACRO button. If you try to program the 17th step, it will be ignored.

•If you do not press any button for more than 30 sec- onds during the procedure, the SEND/LEARN indica- tor flashes three times quickly, then the RC-424M exits Learning mode. Resume Step 1.

•If you make a mistake during programming, the SEND/ LEARN indicator flashes three times quickly, then the RC-424M exits Learning mode. Resume Step 1.

•If you erase one of the operation buttons already programmed in the MACRO MODE button, or if you program a different code into such a button, the operation button will no longer work. In this case, pro- gram the buttons again to avoid malfunction.

36

Page 35 Page 37
Image 36
Page 35 Page 37
Contents DTR-5.1 Important Safeguards Precautions For U.S. modelFor Canadian model Modele pour les CanadienFeatures Supplied accessoriesInstalling the remote controller batteries Using the remote controllerBefore operating this unit Signal flow Audio equipment connectionsVideo equipment connections Digital audio connectionsConnecting other devices Decoder with 5.1 channel outputConnecting other devices Connecting a power cableConnections for remote control AC outlet connectionConnecting speakers Front SpeakersSurround Speakers Center SpeakerConnecting the power Positioning speakersConnecting the antenna cable Connecting the included antennasMaking antenna connections Assembling the AM loop antennaConnecting an FM outdoor antenna Connecting an AM outdoor antennaMaking antenna connections Directional IinkageSpeaker setup Setting the Config parametersConfig Setup Speaker setup Setting the Distance parametersDistance Setup Using the Test Tone function on the main unit Mode Audio button CH SEL button VOL q/u buttonsTest Tone Test button Level +/- buttonsSelecting a sound source DVDSelecting the input signal format Selecting a sound sourceWhen Multi channel input is selected as a source Using the Power On Volume functionPower on Volume Adjusting the tone Bass, Treble Listening through headphones PhonesAbout volume Volume Sleep function Remote controller onlySystem with L/R front and center speakers System with L/R front speakersDolby 3 Stereo StereoUsing Listening Mode Using Listening ModeSetting the Listening mode parameters Late Night Front EffectRe-EQ LFE level control Late NightTuning in a radio station Manual tuningListening to a stereo radio station FM mode Display buttonUsing preset radio stations Mode AudioProgramming radio stations TUNUsing preset radio stations Selecting a preset stationCancelling preset stations Recording a source Recording a source Video 2, Video Tape VCR VideoAdding new sound to a video tape during video editing Enjoying Music and Movies in the Sub-room Outline of Multi-room Remote SystemConnections in the Sub-room Enjoying Music and Movies in the Sub-room Speakers A/BUsing the remote controller Controlling the DTR-5.1Audio Display VOLUsing the remote controller Controlling an Integra/Onkyo CD playerControlling an Integra/Onkyo DVD player DVD Mode SAT, CABLE, VCR, and TV buttons Mode AUDIO/TAPE Mode SAT CABLE, VCR Controlling an Integra/Onkyo MD recorderProgramming procedure Erasing a learned code from a Mode button Mode buttonsErasing a learned code ENTUsing a Macro function What is a Macro function?Programming Macro mode Using a Macro function Programming Macro DirectUsing a Macro function Erasing all codes and operations programmed in the buttons Troubleshooting guide REORemote Control EiajControl positions and names DisplayFront panel 12 13 14Control positions and names Onkyo U.S.A. Corporation
Top Page Image Contents