Eliminator SE400E & SE800E, Section II Installation

Eliminator SE400E & SE800E

Section II – Installation

1.INSTALLATION CAUTION:

ELECTRONIC AIR CLEANERS

CANNOT BE USED IN AREAS WHERE COMBUSTIBLE GASES OR VAPORS ARE PRESENT.

MECHANICAL

The unit has been designed so that it can fit either surface mounted onto the ceiling, semi-recessed into a T-Bar suspended ceiling or wall mounted (SE400E only). When installed with a T-Bar suspended ceiling NEVER support the unit from the T- Bars, the unit must be supported from the permanent ceiling.

SUSPENDED CEILING INSTALLATION

To hang the unit into a suspended ceiling, proceed as follows:

a)Unpack the unit, open filter access door and remove prefilter and cell (see filter removal in section 2).

b)Install ¼-20 eyebolts into mounting slots with large diameter washers and lock-nuts as shown in sketch A. Alternatively, use drop rods.

c)Install trim as shown in sketch A.

d)Select and remove a ceiling tile near the center of the area to be cleaned by the unit.

e)Attach a length of safety chain to each of the four eyebolts or fit threaded rod. Fasten securely.

f)Lift unit into place and support unit while securing to permanent ceiling, ceiling joists, etc. See sketch A.

CAUTION:

IT IS THE RESPONSIBILITY OF THE INSTALLER TO ENSURE ADEQUATE MOUNTING COMPONENTS ARE USED.

DO NOT ALLOW WEIGHT OF UNIT TO

REST ON SUSPENDED CEILING

SUPPORT RAILS.

g)Make electrical connections as detailed in next section.

h)Re-install cell and prefilter.

i)Close access door and unit is ready for operation.

SOLID CEILNG MOUNTING

To mount the unit to a solid ceiling, proceed as follows:

a)Unpack the unit, open filter access door and remove prefilter and cell (see filter removal in section 2).

b)Select a location near the center of the area to be cleaned. lf you are fitting to wooden ceiling joists, locate the position of joists.

c)Using the template provided, drill four holes into the ceiling and fit four 5/16 lag screws in the joists. Hex-headed screws will give easier access for final tightening. Do not tighten fully home.

d)Lift the unit to where the large end of the keyhole slots in the top of the cabinet fit over the screw heads. Slide the unit so that the narrow ends of the mounting slots are located under the screw heads. Tighten the screws fully home.

e)Install the lockdown location screw as shown on template.

f)Make electrical connections as detailed in next section.

g)Re-install cell and pre-filter.

h)Close access door and unit is ready for operation.

WALL MOUNTED (SE400E Only)

Filter removal will be simpler if the unit is positioned with the access door hinge in a vertical plane. Locate the wall studs and follow the mounting instructions for SOLID CEILING MOUNTING.

ELECTRICAL:WARNING:

THIS APPLIANCE MUST BE

ELECTRICALLY GROUNDED.

NOTE: This unit is designed to be permanently connected to fixed wiring. Installation must comply with all applicable electrical codes.

SE800E, SE400E specifications

The Trion SE400E and SE800E are advanced air purification systems designed for commercial and industrial applications. These models are part of Trion's innovative lineup that combines cutting-edge technology with practical functionality to ensure superior air quality in various settings.

One of the standout features of the Trion SE400E and SE800E is their high-efficiency particulate air (HEPA) filtration capability. Both models are equipped with pre-filters and HEPA filters that capture 99.97 percent of particles down to 0.3 microns in size, including dust, pollen, smoke, and other airborne contaminants. This level of filtration is essential in environments where air quality is paramount, such as hospitals, schools, and manufacturing plants.

In addition to HEPA filtration, these units employ electrostatic precipitation technology, enhancing their ability to remove smaller particles that traditional filters may miss. This dual-action filtration system not only improves air quality but also reduces the frequency and costs associated with filter replacement, making it a cost-effective choice for long-term use.

The design of the SE400E and SE800E models is another noteworthy aspect. Both units feature a compact and modular design, allowing for easy installation in various facilities with limited space. They can be mounted on walls or ceilings, providing versatile placement options that do not interfere with the normal operations of the facility.

Furthermore, these air purifiers are equipped with user-friendly controls that allow for easy operation and monitoring. Users can easily adjust fan speeds, set timers, and check filter replacement indicators, facilitating seamless integration into existing air management systems.

The energy efficiency of the Trion SE400E and SE800E is also a key characteristic. These air purification systems are designed to minimize energy consumption while delivering maximum performance, reducing the overall environmental footprint.

Durability and reliability are important traits of the Trion SE400E and SE800E. Built from high-quality materials, these units are engineered to withstand the rigors of daily use in demanding environments, ensuring a long lifespan with minimal maintenance requirements.

In summary, the Trion SE400E and SE800E air purification systems are exemplary models that combine advanced filtration technology, space-saving design, user-friendly control features, energy efficiency, and durability. They provide an effective solution for maintaining high air quality in a variety of commercial and industrial applications, making them a valuable investment for any facility focused on health and safety.