Sanitaire 880 warranty Brush Roll Belt, How To Replace a Worn Belt, How To Change Furniture Guard

Page 7

10.Position end cap with flat sides of center hole over flat sides of threaded shaft (C).

11.Tighten locknut (B).

12.Align holes and secure rubber end cap cover flat side against end cap (A).

When properly assembled, the brush roll should rotate freely between the two end caps. Check the condition of the belt; change if necessary. Replace the brush roll, belt, and bottom plate (see How To Replace A Worn Belt).

Ask for GENUINE EUREKA replacement brush strip. 12 inch No. 52282; 16 inch No. 52246-1

Brush Roll Belt

The brush roll belt on the upright vacuum cleaner drives the brush to agitate, sweep, and comb the carpet nap. The belt should be checked regularly to be sure it is in good condi- tion. Replace the belt if it is stretching, cracking, or slipping. Cut away any hair or thread wound around the brush roll or the belt pulley because the buildup could cause the belt to rotate unevenly.

How To Replace A Worn Belt

3.Place new belt around brush roll.

4.Align brush roll pulley with belt guide.

Belt

Guide

43

5.Place rubber end cap covers over both end caps (flat side against end cap). Align the holes and secure.

Then, slant brush roll forward so end caps are in line with slots in cleaner base.

6. Push brush roll into

5

place.

6

CAUTION: Turn off the switch and unplug the electrical cord before replacing belt. Belt pulleys can become hot during normal use. To prevent burns, avoid touching the belt pulley when servicing the drive belt.

IMPORTANT: Improper installation of the brush roll or brush roll belt could cause carpet or cleaner damage.

11

7

8.Place slots of bottom plate over tabs of cleaner base.

9.Seat and secure cam locks.

7.Place lower side of belt into belt guide and pull to stretch the belt around the left side of motor pulley. Rotate pulley to secure belt into pulley groove.

99

1. Release cam locks and remove bottom plate.

2 Motor

Pulley

2.Pull up on belt to rotate it off the motor pulley. Lift up on brush roll and remove worn belt.

88 Ask for GENUINE EUREKA replacement belts, No. 52100

How To Change Furniture Guard

Four screws on the underside of the base secure the furniture guard.To gain access to the two rear screws, you must remove the four screws holding the two axle clamps and remove the rear wheel assembly. The front two screws are exposed by removing the soleplate and brush roll. Remove the four furniture guard screws, install the new guard and tighten the four screws. Reinstall the brush roll, soleplate and rear wheel assembly.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Commercial Upright Vacuum Cleaner Series Owner’s Guide USA Canada Service InformationRead ALL Instructions Before Using this Vacuum Cleaner General InformationSecure Bellows HOW to AssembleAssembly Packet Grounding InstructionsSecure Cord Clamp Attach Lower HandleExtension Cord Assemble Upper HandleHOW to Maintain HOW to USEC D How To Replace Worn Brush StripsBrush Roll Quick Kleen Fan ChamberHow To Change Furniture Guard How To Replace a Worn BeltBrush Roll Belt Obtaining Warranty Service What this Warranty does not CoverFurther Limitations and Exclusions Guía del propietario Aspiradora vertical Comercial Series LEA Todas LAS Instrucciones Antes DE Usar Esta Aspiradora Información GeneralInformación sobre servicio de reparaciones y partes USA CanadáAsegure el fuelle Instrucciones para hacer conexión a tierraCómo Armarla Paquete para el ensamblajeFije la abrazadera para el cordón Acople el mango de abajoCable alargador Arme el mango de arribaCómo Mantenerla Cómo UsarlaModelos de la Serie 880 únicamente Cámara del ventilador Quick KleenCepillo circular Cómo cambiar las tiras gastadas del cepilloGenuinas DE Eureka Correa del cepillo circularCómo cambiar la correa gastada Cómo cambiar el protector de mueblesLimitaciones Y Exclusiones Adicionales LO QUE no Cubre Esta GarantíaCómo Obtener Servicio Bajo LA Garantía USA CanadáExclusions ET Limitations D’AUTRES Canada 8975-800-800-1 d’Amérique Unis-ÉtatsGarantie LA Appliquer Faire Comment Garantie Cette PAR Couvert PAS N’EST QUI CEUsée courroie une remplacer Comment Choc-pare le changer CommentBrosse-rouleau du courroie La Nouveau DE Assembler Pour Usées poil deBandes les remplacer Comment Brosse-rouleau LeKleen EZ Entretien ’EMPLOI Mode’aspirateur de hauteur la de Réglage InterrupteurRallonge Inférieur manche le Attacher Serrage de collier le InstallerSac du haut le Accrocher Supérieur manche le AssemblerTerre la à mise la pour Instructions Soufflet du place en Mise’assemblage pour pièces des Paquet AssemblageUnis-États Service le sur RenseignementsGénéraux Renseignements Vente-aprèsCom.sanitairevac.www ET Numéros CES Conserver Veuillez

880 specifications

The Sanitaire 880 is a high-performance commercial vacuum cleaner designed to meet the demands of professional cleaning environments such as hotels, offices, and industrial spaces. It combines power, efficiency, and durability, ensuring that cleaning professionals have the reliable tools they need to maintain high standards of cleanliness.

One of the main features of the Sanitaire 880 is its robust motor. This vacuum is equipped with a powerful 10-amp motor that delivers exceptional suction power, allowing it to effectively pick up dirt, debris, and even fine dust particles. This intense suction capability makes it suitable for a variety of surfaces, including carpets, hardwood floors, and tiles, making it a versatile choice for any cleaning task.

The Sanitaire 880 also boasts a user-friendly design. Weighing only 8 pounds, it is lightweight and easy to maneuver, which is essential for professional cleaners who need to cover large areas efficiently. The ergonomically designed handle provides a comfortable grip, reducing fatigue during prolonged use. Additionally, the vacuum features a 12-inch cleaning path, enabling users to cover more ground quickly and effectively, which is particularly advantageous in larger spaces.

In terms of filtration, the Sanitaire 880 incorporates a HEPA filter that captures 99.97% of dust and allergens measuring 0.3 microns and larger. This feature is crucial for maintaining a clean and healthy environment, especially in commercial settings where air quality is vital. The vacuum also includes an easy-to-empty dust cup, simplifying the disposal process and minimizing downtime.

Another noteworthy characteristic of the Sanitaire 880 is its durability. Built with high-quality materials, this vacuum is designed to withstand the rigors of frequent use in challenging conditions. Its reinforced body and components ensure longevity, making it a worthwhile investment for any cleaning service.

In addition to its core features, the Sanitaire 880 stands out for its low noise level, operating quietly to minimize disruption in workspaces. This is particularly beneficial in environments like offices and hotels where noise can be a concern.

In summary, the Sanitaire 880 is a powerful, efficient, and durable vacuum cleaner tailored for professional cleaning applications. With its robust motor, user-friendly design, effective filtration system, and quiet operation, it is a reliable choice for any cleaning professional looking to achieve outstanding results.
Top Page Image Contents