Sunlife Enterprises DM180, DM300, DM240 installation manual Unit Application Data, Location

Page 8

 

 

 

 

356214-XIM-A-0108

TABLE 1: UNIT APPLICATION DATA

 

 

 

 

 

 

 

 

 

UNIT MODEL NUMBER

DM180

DM240

DM300

 

Voltage Variation,

380/415-3-50

 

342/456

 

 

Min. / Max.1

 

 

 

 

 

 

 

 

Supply Air CFM, Min. / Max.

4,500 / 7,200

6,000 / 9,400

7,500 / 12,500

 

 

 

 

 

 

Wet Bulb Temperature (ºF) of Air on

 

57 / 72

 

 

Evaporator Coil, Min. / Max.

 

 

 

 

 

 

 

 

 

 

 

 

Dry Bulb Temperature (ºF) of Air on

 

0 / 125

 

 

Condenser Coil, Min. / Max.

 

 

 

 

 

 

 

1.Utilization range “A” in accordance with ARI Standard 110.

LOCATION

Use the following guidelines to select a suitable loca- tion for these units.

1.Unit is designed for outdoor installation only.

2.Condenser coils must have an unlimited supply of air.

3.Where a choice of location is possible, position the unit on either north or east side of building.

4.For ground level installation, use a level concrete slab with a minimum thickness of 4 inches. The length and width should be at least 6 inches greater than the unit base rails. Do not tie slab to the building foundation.

5.Roof structures must be able to support the weight of the unit and its options and/or accessories. Unit must be installed on a solid level roof curb or appropriate angle iron frame.

6.Maintain level tolerance to 1/2 inch maximum across the entire length or width of the unit.

Excessive exposure of this furnace to contami- nated combustion air may result in equipment damage or personal injury. Typical contami- nates include: permanent wave solutions, chlo- rinated waxes and cleaners, chlorine based swimming pool chemicals, water softening chemicals, carbon tetrachloride, Halogen type refrigerants, cleaning solvents (e.g. perchloro- ethylene), printing inks, paint removers, var- nishes, hydrochloric acid, cements and glues, antistatic fabric softeners for clothes dryers, masonry acid washing materials.

If a unit is to be installed on a roof curb or special frame other than a YORK roof curb, gasketing must be applied to all surfaces that come in contact with the unit

8

Johnson Controls Unitary Products

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Installation Table of Contents List of Figures List of TablesSafety Considerations GeneralInspection ReferenceRenewal Parts ApprovalsProduct Nomenclature Ton Sunline & Magnum & MagnaDRY Model Number NomenclatureLimitations InstallationInstallation Safety Information Unit Application Data LocationRigging and Handling ClearancesDuctwork Fixed Outdoor AIR Intake DamperService Access FiltersField Wiring DM ELECTRIC/ELECTRIC and GAS/ Electric Units Power and Control Wiring Control Wire SizesThermostat Electric Heat Application Data Optional Electric HeatOptional GAS Heat GAS Heat Application DataGAS Piping Pipe SizingExternal Supply Connection External SHUT-OFF Vent and Combustion AIR Hoods Vent and Combustion AIR HoodOptional Power EXHAUST/BAROMETRIC Relief Damper Rain Hood Enthalpy Setpoint Adjustment Four and SIX Point Loads Physical Data ModelsDM Electrical Data -WITHOUT Powered Convenience Outlet SizeDM Electrical Data -WITH Powered Convenience Outlet Front View Rear View Dimensions Unit Clearances and Rain Hood Dimensions 15, 20 & 25 TON Altitude Correction Factors AIR Temp Altitude MeterALTITUDE/TEMPERATURE Conversion Factor High Static Drive CFM 80 m3/s 30 m3/s 10 m3/s 40 m3/s 1030 378 321 258 199 134 1070 417 361 299 240 XIM-A-0108 DM300 Unit Downflow Duct Connections CFM Blower Motor and Drive Data Power Exhaust PerformanceStatic RESISTANCES1 Phasing Checking AIR Supply CFMIWG Drop Pressure Nominal CFM Thousands Supply AIRCooling Sequence of Operation OperationSequence of Operations Overview LOW-PRESSURE Limit Switch Safety Controls ResetCompressor Protection Flash CodesHeating Operation Errors Limit Control SettingHeat Anticipator Setpoints Electric Heat Anticipator SetpointsGAS Heating Operation Errors GAS Valve PipingGAS Valve START-UP Cooling START-UP GAS Heat Shut DownPRE-START Check List POST-START Check List GASManifold GAS Pressure Adjustment Burner AIR Shutter AdjustmentBurner Instructions Checking GAS InputTroubleshooting Adjustment of Temperature RiseCooling Troubleshooting Guide GAS Rate Cubic Feet PER HourXIM-A-0108 XIM-A-0108 XIM-A-0108 XIM-A-0108 GAS Heat Troubleshooting Guide XIM-A-0108 Unit Flash Codes Unit Control Board Flash Codes Unit Control BoardUnit Control Board Option Setup Option Byte SetupXIM-A-0108 Johnson Controls Unitary Products Johnson Controls Unitary Products York Drive Norman, OK

DM300, DM240, DM180 specifications

Sunlife Enterprises has made significant strides in the competitive market of digital management tools with their innovative lineup of products: the DM240, DM300, and DM180. Each of these devices has been engineered to cater to specific operational needs while sharing a common foundation of advanced technology, versatility, and user-centric design.

The DM240 is an entry-level model that caters to small businesses looking for an efficient digital management solution without the hefty price tag. With a compact design and intuitive user interface, the DM240 allows for seamless integration into various work environments. Key features include a high-resolution touchscreen display, which facilitates easy navigation and quick access to essential functions. The device supports wireless connectivity options, ensuring users can manage tasks from anywhere within their operating environment. The energy-efficient design of the DM240 also promotes sustainability without compromising performance.

Moving up the line, the DM300 offers enhanced capabilities for medium-sized enterprises. This model is powered by advanced processing technology, allowing for faster data handling and superior multitasking. The DM300 features expanded memory and storage options, ensuring that users can manage larger datasets effortlessly. Additionally, with built-in advanced security features like biometric authentication and encrypted data storage, businesses can ensure that sensitive information remains protected. The intuitive software interface of the DM300 is designed for ease of use while providing advanced analytics tools to enable users to make data-driven decisions.

At the top of the range is the DM180, a sophisticated solution tailored to large organizations with complex digital management needs. The DM180 showcases a state-of-the-art design with high-performance computing capabilities. It features an expansive multi-touch display, allowing multiple users to interact simultaneously, facilitating collaboration and teamwork. The DM180 is equipped with cloud integration options, promoting real-time data access and sharing among teams, regardless of location. Its scalability ensures that businesses can adapt the system to accommodate growth without compromising functionality. Moreover, it offers comprehensive reporting and analytics tools, empowering organizations to gain valuable insights into their operations.

In summary, Sunlife Enterprises’ DM240, DM300, and DM180 models stand out for their unique features designed to meet the evolving needs of businesses. With a focus on user experience, performance, and security, these devices are poised to help organizations enhance productivity and drive innovation in the digital management landscape.
Top Page Image Contents