Windsor HCC172 Replacing or Removing Scrub Brushes, Installing Scrub Brushes, Squeegee Blades

Page 20

MAINTENANCE

REPLACING OR REMOVING SCRUB BRUSHES

1.Turn the machine off.

FOR SAFETY: Before leaving or servicing the machine; stop on level surface, turn OFF machine.

2.Raise the scrub deck up by pushing down on the pedal.

3.Locate the brush reverse switch on the rear of the panel. Press to activate the motor then release to disconnect brush driver.

4.Tilt and pull machine back to expose brush driver.

INSTALLING SCRUB BRUSHES

1.Turn the machine off.

FOR SAFETY: Before leaving or servicing the machine; stop on level surface, turn OFF machine.

2.Tilt and push machine over brush driver. The brush centering bracket will position the brush driver.

3.Lower the scrub deck by pushing the pedal down and to the left.

4.Locate the brush switch and turn on.

SQUEEGEE BLADES

The front squeegee blade allows solution to pass through channels in the blade into the squeegee assembly while maintaining vacuum to provide lift.

The rear blade wipes the floor to a near dry condition. It is important the rear blade be in good condition to properly do its job.

Check both the front and rear squeegee blades for damage and wear each day in the pre-run check. Change the front blade if it is torn or has an uneven edge. Change the rear blade if it is less than 1/2 the original thickness.

TO REMOVE SQUEEGEE ASSEMBLY

1.With the squeegee in the up position, turn the machine power off.

2.Loosen both squeegee knobs and pull squeegee assembly rearward from the lifting carrier.

3.Inspect or repair as necessary and reinstall.

TO REPLACE SQUEEGEE BLADES

1.With the squeegee in the up position, turn the machine power off.

FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine.

2.Remove the squeegee assembly from the machine. Remove all screws and remove blade retainer strap and remove squeegee blade.

3.Replace squeegee blades as required.

4.Install squeegee blade.

5.Install squeegee retainer strap.

6.Install all screws starting from center and working to ends.

4-5

86221970 17” SCRUBBER 01/03/07

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Automatic Scrubber Machine Data LOG/OVERVIEW OverviewTable of Contents HOW to USE this Manual Important Safety Instructions Read ALL Instructions Before Using this MachineHazard Intensity Level Hazard Intensity LevelSafety Label Location Technical Specifications DIMENSION/CAPACITYMeasure Special NotesHOW this Machine Works Components Controls Squeegee Lift LeverCircuit Breakers Brush SwitchHour Meter Filling Solution Tank Machine OperationsPRE-RUN Machine Inspection Normal ScrubbingEmptying and Cleaning Tanks Solution TankRecovery Tank Machine OperationBatteries WET Cell Batteries only MaintenanceBattery Maintenance Battery Condition Checking GravityTo Charge the Batteries Machines Equipped with Onboard ChargerMachines Without Onboard Charger Changing Batteries Machine stop on level surface, turn off machineFinished Floors Scrub BrushesUncoated Floors Installing Scrub Brushes To Remove Squeegee AssemblyReplacing or Removing Scrub Brushes Squeegee BladesService Schedule Troubleshooting Troubleshooting Problem Cause Solution86221970 17 Scrubber 01/03/07

10066210, 10066270, 10052700, SCH172, 10066230 specifications

Windsor is a renowned name in the realm of technology and innovation, prominently recognized for its advanced cooling solutions and HVAC technologies. Within its impressive portfolio, models such as SCHC172, SCC172, QSCC172IA, 10066260, and 10066220 stand out due to their remarkable features and capabilities.

The SCHC172 model is designed specifically for high-efficiency cooling applications, ideal for both commercial and industrial use. One of its main features includes a robust compressor that significantly enhances the unit's performance and reliability. This model operates with variable speed technology, allowing for better energy management and cost-effectiveness while maintaining optimal cooling conditions.

SCC172, on the other hand, is engineered with a focus on sustainability. It utilizes eco-friendly refrigerants that comply with contemporary environmental standards, minimizing the carbon footprint associated with cooling systems. Moreover, it incorporates advanced diagnostic capabilities that facilitate real-time monitoring and maintenance, ensuring the unit operates at maximum efficiency.

The QSCC172IA model takes innovation a step further by integrating smart technology. This model features an IoT-enabled interface that allows for remote operation and monitoring. Users can control the cooling settings from their smartphones or computers, providing unprecedented convenience and control. The QSCC172IA also includes automated energy-saving features that adjust the system based on current load requirements.

Models 10066260 and 10066220 are tailored for specific industrial applications, featuring heavy-duty construction that withstands rigorous operational conditions. These models boast superb thermal performance and are composed of corrosion-resistant materials that extend their lifespan. With user-friendly interfaces and customizable settings, they can cater to a variety of cooling requirements.

Collectively, these models from Windsor exemplify the brand's commitment to innovation, efficiency, and sustainability in the HVAC sector. By incorporating advanced technologies, eco-friendly materials, and user-focused designs, Windsor not only meets the demanding cooling needs of today's industries but also leads the charge towards a more sustainable future. Their models embody the balance of performance and responsibility that modern consumers seek in technologically advanced cooling solutions. Whether for industrial, commercial, or smart environments, Windsor's products deliver high efficiency and reliability, ensuring comfort and performance year-round.
Top Page Image Contents