Windsor 10052350, SCEX364 manuel dutilisation Solution Strainer, Changing Brush Motors

Page 27

5.SOLUTION STRAINER

The solution strainer is located in front of the left front wheel. The solution strainer protects the solenoid valve from debris. If there is little or no solution flow to the ground, check the strainer for debris. Drain the solution tank and clean the solution strainer. To remove the strainer, turn the bottom part of the strainer counterclockwise until the bottom is separated. Clean out the debris from the wire mesh and re-assemble. Make sure the O-ring gasket is in place when re-assembled.

6.BRUSH MOTOR

!

Do not use a pressure washer to clean around the brush motors. Use tap pressure only.

CHANGING BRUSH MOTORS

1.With the scrub deck in the up position, disconnect brush motor wiring connector from harness.

2.Remove scrub brushes or pad drivers.

3.Remove retaining bolt, lock washer, flat washer and star drive from brush motor shaft.

4.Remove 4 brush motor mounting bolts located under scrub deck.

5.Remove brush motor.

6.Reverse steps to install.

MAINTENANCE

BRUSH MOTOR CARBON BRUSH

REPLACEMENT

1.Remove the cover from the top of the motor by removing the three screws.

2.Note the alignment mark on motor barrel to motor cap. Remove three bolts.

3.Remove end cap with brushes from motor. NOTE: Motors contain two wave washers in cap. Do not lose these.

4.Install the new end cap with brushes and realign with scribe marks on motor barrel. Reinstall the three attach bolts from cap into base.

5.Maintain alignment between motor barrel base and cap.

6.Install the cover on top of the motor with the three screws.

SCEX364 86037160 03/12/07

4-9

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Walk Behind Scrubber Machine Data LOG/OVERVIEW Your DealerOverview Table of Contents Model HOW to USE this ManualRead ALL Instructions Before Using this Machine Important Safety InstructionsHazard Intensity Level Hazard Intensity LevelSafety Label Location DIMENSION/CAPACITY Technical SpecificationsMeasure Special NotesHOW the Machine Works Components Controls Propel Control Levers KEY SwitchEmergency SHUT-OFF Switch Brush SwitchSqueegee Lift Lever Solution Control KnobVacuum Switch Squeegee Pitch Adjustment KnobParking Brake Battery Charge Level IndicatorBrush Pressure Indicator Actuator Switch Deck IN-OUTPRE-RUN Machine Inspection Emergency Stop ProceduresFilling Solution Tank Machine OperationNormal Scrubbing To Begin ScrubbingTo Stop Scrubbing Double Scrub Emptying and Cleaning TanksMaintenance Service Schedule Maintenance Daily Weekly MonthlyHRS Maintenance Batteries Battery MaintenanceChecking Battery Specific Gravity To Charge the Batteries Battery ConditionChecking Gravity Changing Batteries To Replace or Rotate Rear Squeegee Blade Adjusting SqueegeeTo Remove Squeegee Assembly Rear SqueegeeTo Adjust Amount of Rear Squeegee Deflection To Adjust Squeegee PitchUncoated Floors Replacing or Installing Scrub BrushesRecovery Tank Float SHUT-OFF Scrub BrushesChanging Brush Motors Solution StrainerBrush Motor Carbon Brush Replacement Brush MotorBrush Skirts Traction Motor Carbon Brush ReplacementTraction Motor Circuit BreakersChanging Vacuum Motor Vacuum MotorActuator Scrub Deck UP-DOWN REMOVAL/REPLACEMENT Scrub Deck UP-DOWN Actuator AdjustmentActuator Scrub Deck IN-OUT REMOVAL/REPLACEMENT Scrub Deck IN-OUT Actuator AdjustmentTo Replace or Rotate Front Squeegee Blade Front SqueegeeSqueegee Deflection To Adjust Front Squeegee DeflectionRecommended Greasing Problem Cause Solution Machine TroubleshootingMachine Troubleshooting

SCEX364, 10052350 specifications

The Windsor SCEX364,10052350 is an advanced machine designed to revolutionize the cleaning industry, particularly in commercial and industrial applications. This state-of-the-art equipment stands out due to its exceptional performance, innovative technologies, and user-friendly characteristics.

One of the primary features of the Windsor SCEX364,10052350 is its high-capacity cleaning capabilities. With a powerful motor that optimizes suction and scrubbing efficiency, this machine is capable of handling large areas in a fraction of the time it would take with traditional cleaning methods. The machine's scrubbing path is designed for maximum coverage, ensuring that every inch of the floor is cleaned thoroughly.

Advanced technology is at the heart of the Windsor SCEX364,10052350. It is equipped with a sophisticated electronic control system that allows for real-time monitoring of performance metrics. This helps operators to make informed decisions about maintenance and usage, thereby extending the lifespan of the machine. Furthermore, the machine features an integrated water management system, allowing for precise control of water flow and reducing waste. This not only enhances cleaning performance but also supports eco-friendly practices.

In terms of design, the Windsor SCEX364,10052350 prioritizes ease of use and maneuverability. It features a compact and ergonomic structure, enabling operators to navigate tight spaces effortlessly. Additionally, the intuitive control panel makes it easy for users of all skill levels to operate the machine effectively.

Durability is another notable characteristic of the Windsor SCEX364,10052350. Constructed with high-quality materials, this machine can withstand the rigors of frequent use in demanding environments. It is designed to be easily maintainable, with components that can be replaced or serviced without extensive downtime.

Safety considerations are also integrated into the design, with features such as non-slip handles and emergency shut-off systems, ensuring a secure operating experience.

The Windsor SCEX364,10052350 is not just a cleaning machine; it is a comprehensive solution that combines power, efficiency, and user-centric design to meet the rigorous demands of modern cleaning tasks. Its cutting-edge technologies and robust features make it an invaluable asset for any facility looking to maintain high standards of cleanliness and hygiene.
Top Page Image Contents