Windsor 10052350, SCEX364 manuel dutilisation To Replace or Rotate Front Squeegee Blade

Page 31

13. FRONT SQUEEGEE

The front blade allows solution to pass through channels in the blade into the squeegee assembly while maintaining vacuum to provide lift. The front blade has two wear surfaces and can be rotated for extended life. The front blade should not require regular replacement under normal use.

The rear blade wipes the floor to a near dry condition. It is important the rear blade be in good condition to properly do its job. As with the front, each squeegee blade assembly has two wear surfaces for extended service.

Check both the front and rear squeegee blades for damage, wear, and adjustment each day in the pre- run check. Change the front blade if it is torn or has an uneven edge. Change the rear blade if it is less than 1/2 the original thickness.

ADJUSTING SQUEEGEE

The squeegee assembly must have correct deflection at each tip as well as the center. The knobs on the squeegee linkage control the adjustment.

TO REMOVE SQUEEGEE ASSEMBLY

1.With the squeegee and deck in the up position, and the swinging deck in the out position, turn key switch “OFF”.

2.Disconnect vacuum hose from squeegee and loosen both mounting knobs.

3.Pull squeegee assembly rearward from the lifting carrier.

4.Inspect or repair as necessary and reinstall.

MAINTENANCE

TO REPLACE OR ROTATE REAR SQUEEGEE BLADE

1.With the squeegee and deck in the up position, and the swinging deck in the out position, turn key switch “OFF”.

FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine and remove key.

2.Remove the squeegee assembly from the machine. Unscrew the retaining nuts and remove blade retainer strap and remove squeegee blade.

3.Rotate the squeegee to new edge position or replace as required. Each blade has two edge positions.

4.Install blade on locating pins of squeegee assembly.

5.Install squeegee retainer strap.

6.Fasten only tight enough to take up slack in retaining strap.

TO REPLACE OR ROTATE FRONT SQUEEGEE BLADE

1.With the squeegee and deck in the up position, and the swinging deck in the out position, turn key switch “OFF”.

2.Remove the squeegee from the machine. Remove retaining nuts then remove the retainer strap and squeegee blade.

3.Rotate the squeegee to new edge position or replace as required. Each blade has two edge positions. When installing the front blade, tighten the center nut first. Insure that the retainer strap is pressed against the blade before tightening the outer nuts.

SCEX364 86037160 03/12/07

4-13

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Walk Behind Scrubber Your Dealer Machine Data LOG/OVERVIEWOverview Table of Contents Model HOW to USE this ManualRead ALL Instructions Before Using this Machine Important Safety InstructionsHazard Intensity Level Hazard Intensity LevelSafety Label Location DIMENSION/CAPACITY Technical SpecificationsMeasure Special NotesHOW the Machine Works Components Controls Propel Control Levers KEY SwitchEmergency SHUT-OFF Switch Brush SwitchSqueegee Lift Lever Solution Control KnobVacuum Switch Squeegee Pitch Adjustment KnobParking Brake Battery Charge Level IndicatorBrush Pressure Indicator Actuator Switch Deck IN-OUTPRE-RUN Machine Inspection Emergency Stop ProceduresFilling Solution Tank Machine OperationTo Begin Scrubbing Normal ScrubbingTo Stop Scrubbing Double Scrub Emptying and Cleaning TanksMaintenance Daily Weekly Monthly Maintenance Service ScheduleHRS Maintenance Batteries Battery MaintenanceBattery Condition Checking Battery Specific Gravity To Charge the BatteriesChecking Gravity Changing Batteries To Replace or Rotate Rear Squeegee Blade Adjusting SqueegeeTo Remove Squeegee Assembly Rear SqueegeeTo Adjust Amount of Rear Squeegee Deflection To Adjust Squeegee PitchUncoated Floors Replacing or Installing Scrub BrushesRecovery Tank Float SHUT-OFF Scrub BrushesChanging Brush Motors Solution StrainerBrush Motor Carbon Brush Replacement Brush MotorBrush Skirts Traction Motor Carbon Brush ReplacementTraction Motor Circuit BreakersChanging Vacuum Motor Vacuum MotorActuator Scrub Deck UP-DOWN REMOVAL/REPLACEMENT Scrub Deck UP-DOWN Actuator AdjustmentActuator Scrub Deck IN-OUT REMOVAL/REPLACEMENT Scrub Deck IN-OUT Actuator AdjustmentTo Replace or Rotate Front Squeegee Blade Front SqueegeeSqueegee Deflection To Adjust Front Squeegee DeflectionRecommended Greasing Problem Cause Solution Machine TroubleshootingMachine Troubleshooting

SCEX364, 10052350 specifications

The Windsor SCEX364,10052350 is an advanced machine designed to revolutionize the cleaning industry, particularly in commercial and industrial applications. This state-of-the-art equipment stands out due to its exceptional performance, innovative technologies, and user-friendly characteristics.

One of the primary features of the Windsor SCEX364,10052350 is its high-capacity cleaning capabilities. With a powerful motor that optimizes suction and scrubbing efficiency, this machine is capable of handling large areas in a fraction of the time it would take with traditional cleaning methods. The machine's scrubbing path is designed for maximum coverage, ensuring that every inch of the floor is cleaned thoroughly.

Advanced technology is at the heart of the Windsor SCEX364,10052350. It is equipped with a sophisticated electronic control system that allows for real-time monitoring of performance metrics. This helps operators to make informed decisions about maintenance and usage, thereby extending the lifespan of the machine. Furthermore, the machine features an integrated water management system, allowing for precise control of water flow and reducing waste. This not only enhances cleaning performance but also supports eco-friendly practices.

In terms of design, the Windsor SCEX364,10052350 prioritizes ease of use and maneuverability. It features a compact and ergonomic structure, enabling operators to navigate tight spaces effortlessly. Additionally, the intuitive control panel makes it easy for users of all skill levels to operate the machine effectively.

Durability is another notable characteristic of the Windsor SCEX364,10052350. Constructed with high-quality materials, this machine can withstand the rigors of frequent use in demanding environments. It is designed to be easily maintainable, with components that can be replaced or serviced without extensive downtime.

Safety considerations are also integrated into the design, with features such as non-slip handles and emergency shut-off systems, ensuring a secure operating experience.

The Windsor SCEX364,10052350 is not just a cleaning machine; it is a comprehensive solution that combines power, efficiency, and user-centric design to meet the rigorous demands of modern cleaning tasks. Its cutting-edge technologies and robust features make it an invaluable asset for any facility looking to maintain high standards of cleanliness and hygiene.
Top Page Image Contents