Windsor 10052350, SCEX364 To Adjust Squeegee Pitch, To Adjust Amount of Rear Squeegee Deflection

Page 25

TO ADJUST SQUEEGEE PITCH

1.Choose a smooth, level surface. Turn “ON” the key switch. Lower the squeegee and drive forward at least 2 feet (60cm.).

2.With the squeegee down, stop the machine. Do not allow machine to roll back.

FOR SAFETY: Before leaving or servicing the machine; stop on level surface, turn off machine and remove key.

3.Determine the differences, if any, in deflection of the squeegee blade between each end and the middle. Proper adjustment is obtained when deflection is equal all the way across the squeegee blade. The bubble level should also indicate when the squeegee is adjusted properly. When the air bubble is in the center of the vial, the deflection should be even across the squeegee blade.

4.To decrease the deflection of the squeegee blade at the ends, tighten knob near the squeegee center. To increase the deflection at the ends of the squeegee assembly, loosen knob.

5.Check the deflection of the squeegee blades again. Repeat steps 1 through 4 until the deflection is equal across the entire rear squeegee blade.

MAINTENANCE

TO ADJUST AMOUNT OF REAR SQUEEGEE DEFLECTION

1.Choose a smooth, level surface. Lower the squeegee and drive forward at least 2 feet (60cm).

2.With the squeegee down, stop the machine. Do not allow machine to roll back.

FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine and remove key.

3.Observe the amount of squeegee deflection. It should deflect 3/8 in. (9.5mm) across the entire width of the squeegee.

4.To increase the squeegee deflection, turn the 2 knobs at the squeegee ends counter-clockwise. To decrease the deflection, turn the knobs clockwise.

NOTE: The deflection should be consistent along the length of the squeegee. If the deflection varies from end to end the knobs can be adjusted independently to correct the variation.

5.Turn on the key switch. Raise, then lower squeegee assembly. Drive forward at least 2 feet (60cm).

6.Repeat steps 2 through 4 until deflection of 3/8 in. (9.5mm) is reached.

SQUEEGEE DEFLECTION

CORRECT

NOT ENOUGH

TOO MUCH

SIDE VIEW OF SQUEEGEE BLADE

SCEX364 86037160 03/12/07

4-7

 

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Walk Behind Scrubber Your Dealer Machine Data LOG/OVERVIEWOverview Table of Contents Model HOW to USE this ManualRead ALL Instructions Before Using this Machine Important Safety InstructionsHazard Intensity Level Hazard Intensity LevelSafety Label Location DIMENSION/CAPACITY Technical SpecificationsMeasure Special NotesHOW the Machine Works Components Controls Emergency SHUT-OFF Switch KEY SwitchBrush Switch Propel Control LeversVacuum Switch Solution Control KnobSqueegee Pitch Adjustment Knob Squeegee Lift LeverBrush Pressure Indicator Battery Charge Level IndicatorActuator Switch Deck IN-OUT Parking BrakeFilling Solution Tank Emergency Stop ProceduresMachine Operation PRE-RUN Machine InspectionTo Begin Scrubbing Normal ScrubbingTo Stop Scrubbing Double Scrub Emptying and Cleaning TanksMaintenance Daily Weekly Monthly Maintenance Service ScheduleHRS Maintenance Batteries Battery MaintenanceBattery Condition Checking Battery Specific Gravity To Charge the BatteriesChecking Gravity Changing Batteries To Remove Squeegee Assembly Adjusting SqueegeeRear Squeegee To Replace or Rotate Rear Squeegee BladeTo Adjust Amount of Rear Squeegee Deflection To Adjust Squeegee PitchRecovery Tank Float SHUT-OFF Replacing or Installing Scrub BrushesScrub Brushes Uncoated FloorsBrush Motor Carbon Brush Replacement Solution StrainerBrush Motor Changing Brush MotorsTraction Motor Traction Motor Carbon Brush ReplacementCircuit Breakers Brush SkirtsChanging Vacuum Motor Vacuum MotorActuator Scrub Deck IN-OUT REMOVAL/REPLACEMENT Scrub Deck UP-DOWN Actuator AdjustmentScrub Deck IN-OUT Actuator Adjustment Actuator Scrub Deck UP-DOWN REMOVAL/REPLACEMENTTo Replace or Rotate Front Squeegee Blade Front SqueegeeSqueegee Deflection To Adjust Front Squeegee DeflectionRecommended Greasing Problem Cause Solution Machine TroubleshootingMachine Troubleshooting

SCEX364, 10052350 specifications

The Windsor SCEX364,10052350 is an advanced machine designed to revolutionize the cleaning industry, particularly in commercial and industrial applications. This state-of-the-art equipment stands out due to its exceptional performance, innovative technologies, and user-friendly characteristics.

One of the primary features of the Windsor SCEX364,10052350 is its high-capacity cleaning capabilities. With a powerful motor that optimizes suction and scrubbing efficiency, this machine is capable of handling large areas in a fraction of the time it would take with traditional cleaning methods. The machine's scrubbing path is designed for maximum coverage, ensuring that every inch of the floor is cleaned thoroughly.

Advanced technology is at the heart of the Windsor SCEX364,10052350. It is equipped with a sophisticated electronic control system that allows for real-time monitoring of performance metrics. This helps operators to make informed decisions about maintenance and usage, thereby extending the lifespan of the machine. Furthermore, the machine features an integrated water management system, allowing for precise control of water flow and reducing waste. This not only enhances cleaning performance but also supports eco-friendly practices.

In terms of design, the Windsor SCEX364,10052350 prioritizes ease of use and maneuverability. It features a compact and ergonomic structure, enabling operators to navigate tight spaces effortlessly. Additionally, the intuitive control panel makes it easy for users of all skill levels to operate the machine effectively.

Durability is another notable characteristic of the Windsor SCEX364,10052350. Constructed with high-quality materials, this machine can withstand the rigors of frequent use in demanding environments. It is designed to be easily maintainable, with components that can be replaced or serviced without extensive downtime.

Safety considerations are also integrated into the design, with features such as non-slip handles and emergency shut-off systems, ensuring a secure operating experience.

The Windsor SCEX364,10052350 is not just a cleaning machine; it is a comprehensive solution that combines power, efficiency, and user-centric design to meet the rigorous demands of modern cleaning tasks. Its cutting-edge technologies and robust features make it an invaluable asset for any facility looking to maintain high standards of cleanliness and hygiene.
Top Page Image Contents