Windsor SCEX364, 10052350 Rear Squeegee, Adjusting Squeegee, To Remove Squeegee Assembly

Page 24

MAINTENANCE

2. REAR SQUEEGEE

The front blade allows solution to pass through channels in the blade into the squeegee assembly while maintaining vacuum to provide lift. The front blade has four wear surfaces and can be rotated for extended life. The front blade should not require regular replacement under normal use.

The rear blade wipes the floor to a near dry condition. It is important the rear blade be in good condition to properly do its job. As with the front, each squeegee blade assembly has four wear surfaces for extended service.

Check both the front and rear squeegee blades for damage, wear, and adjustment each day in the pre- run check. Change the front blade if it is torn or has an uneven edge. Change the rear blade if it is less than 1/2 the original thickness.

ADJUSTING SQUEEGEE

Adjusting the squeegee is a two-part process. First, the squeegee assembly must have correct pitch in order for the squeegee blade to have the same deflection at each tip as well as the center. The knob on the squeegee linkage controls the pitch adjustment. The second adjustment is the deflection. Knobs on each end of the squeegee control this.

TO REMOVE SQUEEGEE ASSEMBLY

1.With the squeegee in the up position, turn key switch “OFF”.

2.Disconnect vacuum hose from squeegee and loosen both knobs.

3.Pull squeegee assembly rearward from the lifting carrier.

4.Inspect or repair as necessary and reinstall.

TO REPLACE OR ROTATE REAR SQUEEGEE BLADE

1.With the squeegee in the up position, turn key switch “OFF”.

FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine and remove key.

2.Remove the squeegee assembly from the machine. Unlatch and remove blade retainer strap and remove squeegee blade.

3.Rotate the squeegee to new edge position or replace as required. Each blade has four new edge positions.

4.Install blade on locating pins of squeegee assembly.

5.Install squeegee retainer strap.

6.Fasten and lock latch, adjust latch only tight enough to take up slack in retaining strap.

4-6

SCEX364 86037160 03/12/07

 

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Walk Behind Scrubber Machine Data LOG/OVERVIEW Your DealerOverview Table of Contents HOW to USE this Manual ModelImportant Safety Instructions Read ALL Instructions Before Using this MachineHazard Intensity Level Hazard Intensity LevelSafety Label Location Technical Specifications DIMENSION/CAPACITYSpecial Notes MeasureHOW the Machine Works Components Controls KEY Switch Emergency SHUT-OFF SwitchBrush Switch Propel Control LeversSolution Control Knob Vacuum SwitchSqueegee Pitch Adjustment Knob Squeegee Lift LeverBattery Charge Level Indicator Brush Pressure IndicatorActuator Switch Deck IN-OUT Parking BrakeEmergency Stop Procedures Filling Solution TankMachine Operation PRE-RUN Machine InspectionNormal Scrubbing To Begin ScrubbingTo Stop Scrubbing Emptying and Cleaning Tanks Double ScrubMaintenance Service Schedule Maintenance Daily Weekly MonthlyHRS Maintenance Battery Maintenance BatteriesChecking Battery Specific Gravity To Charge the Batteries Battery ConditionChecking Gravity Changing Batteries Adjusting Squeegee To Remove Squeegee AssemblyRear Squeegee To Replace or Rotate Rear Squeegee BladeTo Adjust Squeegee Pitch To Adjust Amount of Rear Squeegee DeflectionReplacing or Installing Scrub Brushes Recovery Tank Float SHUT-OFFScrub Brushes Uncoated FloorsSolution Strainer Brush Motor Carbon Brush ReplacementBrush Motor Changing Brush MotorsTraction Motor Carbon Brush Replacement Traction MotorCircuit Breakers Brush SkirtsVacuum Motor Changing Vacuum MotorScrub Deck UP-DOWN Actuator Adjustment Actuator Scrub Deck IN-OUT REMOVAL/REPLACEMENTScrub Deck IN-OUT Actuator Adjustment Actuator Scrub Deck UP-DOWN REMOVAL/REPLACEMENTFront Squeegee To Replace or Rotate Front Squeegee BladeTo Adjust Front Squeegee Deflection Squeegee DeflectionRecommended Greasing Machine Troubleshooting Problem Cause SolutionMachine Troubleshooting

SCEX364, 10052350 specifications

The Windsor SCEX364,10052350 is an advanced machine designed to revolutionize the cleaning industry, particularly in commercial and industrial applications. This state-of-the-art equipment stands out due to its exceptional performance, innovative technologies, and user-friendly characteristics.

One of the primary features of the Windsor SCEX364,10052350 is its high-capacity cleaning capabilities. With a powerful motor that optimizes suction and scrubbing efficiency, this machine is capable of handling large areas in a fraction of the time it would take with traditional cleaning methods. The machine's scrubbing path is designed for maximum coverage, ensuring that every inch of the floor is cleaned thoroughly.

Advanced technology is at the heart of the Windsor SCEX364,10052350. It is equipped with a sophisticated electronic control system that allows for real-time monitoring of performance metrics. This helps operators to make informed decisions about maintenance and usage, thereby extending the lifespan of the machine. Furthermore, the machine features an integrated water management system, allowing for precise control of water flow and reducing waste. This not only enhances cleaning performance but also supports eco-friendly practices.

In terms of design, the Windsor SCEX364,10052350 prioritizes ease of use and maneuverability. It features a compact and ergonomic structure, enabling operators to navigate tight spaces effortlessly. Additionally, the intuitive control panel makes it easy for users of all skill levels to operate the machine effectively.

Durability is another notable characteristic of the Windsor SCEX364,10052350. Constructed with high-quality materials, this machine can withstand the rigors of frequent use in demanding environments. It is designed to be easily maintainable, with components that can be replaced or serviced without extensive downtime.

Safety considerations are also integrated into the design, with features such as non-slip handles and emergency shut-off systems, ensuring a secure operating experience.

The Windsor SCEX364,10052350 is not just a cleaning machine; it is a comprehensive solution that combines power, efficiency, and user-centric design to meet the rigorous demands of modern cleaning tasks. Its cutting-edge technologies and robust features make it an invaluable asset for any facility looking to maintain high standards of cleanliness and hygiene.
Top Page Image Contents