Windsor SCEX364 Scrub Deck UP-DOWN Actuator Adjustment, Scrub Deck IN-OUT Actuator Adjustment

Page 30

MAINTENANCE

11.ACTUATOR SCRUB DECK UP-DOWN REMOVAL/REPLACEMENT

FOR SAFETY: Before leaving or servicing machine, stop on a level surface, turn off machine and set parking brake (If option is installed).

1.Remove front cover.

2.Remove clevis pin and rue ring from lower bracket of actuator; do not allow actuator barrel to rotate.

3.Disconnect actuator from wiring harness.

4.Remove upper clevis pin and rue ring from actuator bracket.

5.Reverse steps to install.

SCRUB DECK UP-DOWN ACTUATOR ADJUSTMENT

The actuator will need to be adjusted when replaced.

To adjust the actuator:

1.While holding actuator barrel to prevent it from spinning, apply power to the actuator such that it is fully extended. Positive power to white wire, and negative/ground to black. Limit switch within actuator will stop it.

2.Turn barrel out one or more full turns to assure that when it is retracted it will not bind against itself.

3.While holding actuator barrel to prevent it from spinning, apply power to the actuator such that it is fully retracted. Positive power to black wire, and negative/ground to white wire. Limit switch within actuator will stop it.

4.With actuator fully retracted, turn barrel in until it touches the base of the threaded shaft.

5.At the bottomed out position, turn the barrel out 1 1/2 turns, then enough more to allow connection to lift linkage.

6.Connect actuator to lift linkage.

7.Check travel of actuator during operation.

12.ACTUATOR SCRUB DECK IN-OUT REMOVAL/REPLACEMENT

FOR SAFETY: Before leaving or servicing machine, stop on a level surface, turn off machine and set parking brake (If option is installed).

1.Remove front cover.

2.Swing the deck to the fully open position. This will align the access holes in the deck plates so that the clevis pin can be removed.

3.Remove the clevis pin and rue ring from both ends of the actuator.

4.Disconnect actuator from wiring harness.

5.Reverse steps to install.

SCRUB DECK IN-OUT ACTUATOR ADJUSTMENT

The actuator will need to be adjusted when replaced.

To adjust the actuator:

1.While holding actuator barrel to prevent it from spinning, apply power to the actuator such that it is fully extended. Positive power to white wire, and negative/ground to black. Limit switch within actuator will stop it.

2.Turn barrel out one or more full turns to assure that when it is retracted it will not bind against itself.

3.While holding actuator barrel to prevent it from spinning, apply power to the actuator such that it is fully retracted. Positive power to black wire, and negative/ground to white wire. Limit switch within actuator will stop it.

4.With actuator fully retracted, turn barrel in until it touches the base of the threaded shaft.

5.At the bottomed out position, turn the barrel out 1/2 of a turn, then enough more to allow connection to linkage.

6.Connect actuator to linkage.

7.Check travel of actuator during operation.

4-12

SCEX364 86037160 03/12/07

 

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Walk Behind Scrubber Machine Data LOG/OVERVIEW Your DealerOverview Table of Contents HOW to USE this Manual ModelImportant Safety Instructions Read ALL Instructions Before Using this MachineHazard Intensity Level Hazard Intensity LevelSafety Label Location Technical Specifications DIMENSION/CAPACITYSpecial Notes MeasureHOW the Machine Works Components Controls Brush Switch KEY SwitchEmergency SHUT-OFF Switch Propel Control LeversSqueegee Pitch Adjustment Knob Solution Control KnobVacuum Switch Squeegee Lift LeverActuator Switch Deck IN-OUT Battery Charge Level IndicatorBrush Pressure Indicator Parking BrakeMachine Operation Emergency Stop ProceduresFilling Solution Tank PRE-RUN Machine InspectionNormal Scrubbing To Begin ScrubbingTo Stop Scrubbing Emptying and Cleaning Tanks Double ScrubMaintenance Service Schedule Maintenance Daily Weekly MonthlyHRS Maintenance Battery Maintenance BatteriesChecking Battery Specific Gravity To Charge the Batteries Battery ConditionChecking Gravity Changing Batteries Rear Squeegee Adjusting SqueegeeTo Remove Squeegee Assembly To Replace or Rotate Rear Squeegee BladeTo Adjust Squeegee Pitch To Adjust Amount of Rear Squeegee DeflectionScrub Brushes Replacing or Installing Scrub BrushesRecovery Tank Float SHUT-OFF Uncoated FloorsBrush Motor Solution StrainerBrush Motor Carbon Brush Replacement Changing Brush MotorsCircuit Breakers Traction Motor Carbon Brush ReplacementTraction Motor Brush SkirtsVacuum Motor Changing Vacuum MotorScrub Deck IN-OUT Actuator Adjustment Scrub Deck UP-DOWN Actuator AdjustmentActuator Scrub Deck IN-OUT REMOVAL/REPLACEMENT Actuator Scrub Deck UP-DOWN REMOVAL/REPLACEMENTFront Squeegee To Replace or Rotate Front Squeegee BladeTo Adjust Front Squeegee Deflection Squeegee DeflectionRecommended Greasing Machine Troubleshooting Problem Cause SolutionMachine Troubleshooting

SCEX364, 10052350 specifications

The Windsor SCEX364,10052350 is an advanced machine designed to revolutionize the cleaning industry, particularly in commercial and industrial applications. This state-of-the-art equipment stands out due to its exceptional performance, innovative technologies, and user-friendly characteristics.

One of the primary features of the Windsor SCEX364,10052350 is its high-capacity cleaning capabilities. With a powerful motor that optimizes suction and scrubbing efficiency, this machine is capable of handling large areas in a fraction of the time it would take with traditional cleaning methods. The machine's scrubbing path is designed for maximum coverage, ensuring that every inch of the floor is cleaned thoroughly.

Advanced technology is at the heart of the Windsor SCEX364,10052350. It is equipped with a sophisticated electronic control system that allows for real-time monitoring of performance metrics. This helps operators to make informed decisions about maintenance and usage, thereby extending the lifespan of the machine. Furthermore, the machine features an integrated water management system, allowing for precise control of water flow and reducing waste. This not only enhances cleaning performance but also supports eco-friendly practices.

In terms of design, the Windsor SCEX364,10052350 prioritizes ease of use and maneuverability. It features a compact and ergonomic structure, enabling operators to navigate tight spaces effortlessly. Additionally, the intuitive control panel makes it easy for users of all skill levels to operate the machine effectively.

Durability is another notable characteristic of the Windsor SCEX364,10052350. Constructed with high-quality materials, this machine can withstand the rigors of frequent use in demanding environments. It is designed to be easily maintainable, with components that can be replaced or serviced without extensive downtime.

Safety considerations are also integrated into the design, with features such as non-slip handles and emergency shut-off systems, ensuring a secure operating experience.

The Windsor SCEX364,10052350 is not just a cleaning machine; it is a comprehensive solution that combines power, efficiency, and user-centric design to meet the rigorous demands of modern cleaning tasks. Its cutting-edge technologies and robust features make it an invaluable asset for any facility looking to maintain high standards of cleanliness and hygiene.
Top Page Image Contents