Windsor SC326 10052220 manual Squeegee Blades, Adjusting Squeegee, To Remove Squeegee Assembly

Page 24

MAINTENANCE

2. SQUEEGEE BLADES

The front squeegee blade allows solution to pass through channels in the blade into the squeegee assembly while maintaining vacuum to provide lift. The front blade has four wear surfaces and can be rotated for extended life. The front blade should not require regular replacement under normal use.

The rear blade wipes the floor to a near dry condition. It is important the rear blade be in good condition to properly do its job. As with the front, each squeegee blade assembly has four wear surfaces for extended service.

Check both the front and rear squeegee blades for damage, wear, and adjustment each day in the pre- run check. Change the front blade if it is torn or has an uneven edge. Change the rear blade if it is less than 1/2 the original thickness.

ADJUSTING SQUEEGEE

Adjusting the squeegee is a two-part process. First, the squeegee assembly must have correct pitch in order for the squeegee blade to have the same deflection at each tip as well as the center. The knob on the squeegee linkage controls the pitch adjustment. The second adjustment is the deflection. Knobs on each end of the squeegee control this.

SQUEEGEE DEFLECTION

CORRECT

NOT ENOUGH

TOO MUCH

SQUEEGEE SIDE VIEW OF

TO REMOVE SQUEEGEE ASSEMBLY

1.With the squeegee in the up position, turn key switch “OFF”.

2.Disconnect vacuum hose from squeegee and loosen both knobs.

3.Pull squeegee assembly rearward from the lifting carrier.

4.Inspect or repair as necessary and reinstall.

TO REPLACE OR ROTATE REAR SQUEEGEE BLADES

1.With the squeegee in the up position, turn key switch “OFF”.

FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine and remove key.

2.Remove the squeegee assembly from the machine. Unlatch and remove blade retainer strap and remove squeegee blade.

3.Rotate the squeegee to new edge position or replace as required. Each blade has four new edge positions.

4.Install blade on locating pins of squeegee assembly.

5.Install squeegee retainer strap.

6.Fasten and lock latch, adjust latch only tight enough to take up slack in retaining strap.

TO REPLACE OR ROTATE FRONT SQUEEGEE BLADE

1.With the squeegee in the up position, turn key switch “OFF”.

2.Remove the squeegee from the machine. Loosen three thumbscrews and remove the retainer strap and squeegee blade.

3.Rotate the squeegee to new edge position or replace as required. Each blade has four new edge positions. When installing the front blade, tighten the center thumbscrew first. Insure that the retainer strap is pressed against the blade before tightening the outer screws.

4-6

CUTTER 36V 86039090 04/03/07

 

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Walk Behind Scrubber Machine Data LOG/OVERVIEW Your DealerOverview Table of Contents HOW to USE this Manual ModelImportant Safety Instructions Read ALL Instructions Before Using this MachineHazard Intensity Level Hazard Intensity LevelSafety Label Location Technical Specifications DIMENSION/CAPACITYSpecial Notes MeasureHOW the Machine Works Components Controls KEY Switch Emergency SHUT-OFF Switch OptionalBrush Switch Solution Control Knob Vacuum SwitchSqueegee Pitch Adjustment Knob Squeegee Deflection Adjustment KnobsParking Brake Optional Hour Meter OptionalEmergency Stop Procedures Filling Solution TankMachine Operation PRE-RUN Machine InspectionNormal Scrubbing To Begin ScrubbingTo Stop Scrubbing Emptying and Cleaning Tanks Double ScrubMaintenance Service Schedule Maintenance Daily Weekly MonthlyHRS Maintenance Battery Maintenance BatteriesChecking Battery Specific Gravity To Charge the Batteries Battery ConditionChecking Gravity Changing Batteries Front of MachineAdjusting Squeegee To Remove Squeegee AssemblySqueegee Blades To Replace or Rotate Rear Squeegee BladesTo Adjust Squeegee Pitch To Adjust Amount of Rear Squeegee DeflectionTo Replace AQUA-MIZER Squeegee Blades Replacing or Installing Scrub Brushes Recovery Tank Float SHUT-OFFScrub Brushes Uncoated FloorsSolution Strainer Brush Motor Carbon Brush ReplacementBrush Motor Changing Brush MotorsTraction Motor Carbon Brush Replacement Traction MotorCircuit Breakers Brush Shrouds & Brush SkirtsVacuum Motor Changing Vacuum MotorMachine Troubleshooting Problem Cause SolutionMachine Troubleshooting

SC326 10052220, SCC326 10052260 specifications

The Windsor SCC326 and SC326 series represent innovative advancements in industrial cleaning equipment, designed to enhance efficiency and productivity in various environments. Specifically tailored for heavy-duty cleaning applications, these floor scrubbers combine powerful performance with user-centric features.

The SCC326 model boasts a robust design that is perfect for large commercial spaces like warehouses, airports, and shopping centers. Equipped with a high-capacity solution tank, the SCC326 enables prolonged cleaning sessions without frequent refills, minimizing downtime. The brush system utilizes dual rotating brushes to effectively agitate dirt and grime from surfaces, while the innovative scrub deck design allows for superior maneuverability in tight areas.

On the other hand, the SC326 model shares many of these characteristics but places an added emphasis on eco-friendly operation. With a focus on sustainability, the SC326 incorporates a smart scrub feature that optimizes water and chemical usage, ensuring that cleaning solutions are applied precisely where needed. This not only reduces environmental impact but also lowers operational costs over time.

Both models utilize advanced technology in their respective operations. They come equipped with an onboard diagnostic system, providing real-time feedback on performance and maintenance needs. This feature assists operators in staying informed about the machine's condition and significantly enhances reliability.

Ergonomically designed controls on both models ensure that users can operate them with minimal strain, promoting comfort during extended use. Additionally, their compact design allows for easy storage and transport, making them an excellent choice for businesses with diverse cleaning needs.

In terms of safety, both SCC326 and SC326 are fitted with automatic shut-off systems that activate in case of emergencies, thereby protecting users and equipment alike. This attention to safety standards reflects Windsor's commitment to providing top-tier cleaning solutions.

Ultimately, the Windsor SCC326 and SC326 series embody a blend of power, efficiency, and safety, catering to the rigorous demands of industrial cleaning tasks. Whether addressing large-scale surface areas or caring for intricate spaces, these models are engineered to deliver superior performance without compromising ease of use or environmental responsibility.
Top Page Image Contents