Windsor SC326 10052220, SCC326 10052260 Checking Battery Specific Gravity To Charge the Batteries

Page 22

MAINTENANCE

 

CHECKING BATTERY SPECIFIC GRAVITY

TO CHARGE THE BATTERIES

Use a hydrometer to check the battery specific

!

gravity.

 

When servicing machine, avoid contact with

 

battery acid.

Battery Check

!

 

Batteries emit hydrogen gas. Explosion or fire

 

can result. Keep sparks and open flame away.

 

Keep covers open when charging.

!

Wear eye protection and protective clothing when working with batteries.

CHECKING GRAVITY

A.Hydrometer

B.Battery

NOTE: Do not take readings immediately after adding distilled water, if the water and acid are not thoroughly mixed, the reading may not be accurate.

Check the hydrometer readings against this chart.

SPECIFIC GRAVITY

BATTERY CONDITION

@ 80° F (27°C)

 

1.265

100% CHARGED

1.225

75% CHARGED

1.190

50% CHARGED

1.155

25% CHARGED

1.120

DISCHARGED

NOTE: If the readings are taken when the battery electrolyte is any temperature other than 80°F

(27°C), the reading must be temperature corrected.

To find the corrected specific gravity reading when the temperature of the battery electrolyte is other than 80°F (27°): Add (+) to the specific gravity reading 0.004 (4 points), for each 10°F (6°C) above 80° (27°C).

Subtract (-) from the specific reading 0.004 (4 points), for each 10°F (6°C) below 80°F (27°C).

!

Charge batteries in a well ventilated area. Leave the battery cover open.

Use a 36 volt, 18 amp maximum output or 25 amp (depending on the size of the batteries), DC charger which will automatically shut off when the batteries are fully charged.

1.Stop the machine in a clean, well ventilated area next to the charger. w

2.Turn “OFF” machine.

FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine and remove key.

3.Raise the battery cover.

!

Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep covers open when charging.

4.Check the electrolyte level in each battery cell. Before charging, add just enough distilled water to cover the plates. After charging is complete, add just enough distilled water to bring up the level to the indicator ring. If the water level is too high before charging, normal expansion rate of the electrolyte may cause an overflow. Resulting in a loss of battery acid balance and damage the machine.

4-4

CUTTER 36V 86039090 04/03/07

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Walk Behind Scrubber Your Dealer Machine Data LOG/OVERVIEWOverview Table of Contents HOW to USE this Manual ModelImportant Safety Instructions Read ALL Instructions Before Using this MachineHazard Intensity Level Hazard Intensity LevelSafety Label Location Technical Specifications DIMENSION/CAPACITYSpecial Notes MeasureHOW the Machine Works Components Controls Emergency SHUT-OFF Switch Optional KEY SwitchBrush Switch Squeegee Pitch Adjustment Knob Solution Control KnobVacuum Switch Squeegee Deflection Adjustment KnobsParking Brake Optional Hour Meter OptionalMachine Operation Emergency Stop ProceduresFilling Solution Tank PRE-RUN Machine InspectionTo Begin Scrubbing Normal ScrubbingTo Stop Scrubbing Emptying and Cleaning Tanks Double ScrubMaintenance Daily Weekly Monthly Maintenance Service ScheduleHRS Maintenance Battery Maintenance BatteriesBattery Condition Checking Battery Specific Gravity To Charge the BatteriesChecking Gravity Changing Batteries Front of MachineSqueegee Blades Adjusting SqueegeeTo Remove Squeegee Assembly To Replace or Rotate Rear Squeegee BladesTo Adjust Amount of Rear Squeegee Deflection To Adjust Squeegee PitchTo Replace AQUA-MIZER Squeegee Blades Scrub Brushes Replacing or Installing Scrub BrushesRecovery Tank Float SHUT-OFF Uncoated FloorsBrush Motor Solution StrainerBrush Motor Carbon Brush Replacement Changing Brush MotorsCircuit Breakers Traction Motor Carbon Brush ReplacementTraction Motor Brush Shrouds & Brush SkirtsVacuum Motor Changing Vacuum MotorMachine Troubleshooting Problem Cause SolutionMachine Troubleshooting

SC326 10052220, SCC326 10052260 specifications

The Windsor SCC326 and SC326 series represent innovative advancements in industrial cleaning equipment, designed to enhance efficiency and productivity in various environments. Specifically tailored for heavy-duty cleaning applications, these floor scrubbers combine powerful performance with user-centric features.

The SCC326 model boasts a robust design that is perfect for large commercial spaces like warehouses, airports, and shopping centers. Equipped with a high-capacity solution tank, the SCC326 enables prolonged cleaning sessions without frequent refills, minimizing downtime. The brush system utilizes dual rotating brushes to effectively agitate dirt and grime from surfaces, while the innovative scrub deck design allows for superior maneuverability in tight areas.

On the other hand, the SC326 model shares many of these characteristics but places an added emphasis on eco-friendly operation. With a focus on sustainability, the SC326 incorporates a smart scrub feature that optimizes water and chemical usage, ensuring that cleaning solutions are applied precisely where needed. This not only reduces environmental impact but also lowers operational costs over time.

Both models utilize advanced technology in their respective operations. They come equipped with an onboard diagnostic system, providing real-time feedback on performance and maintenance needs. This feature assists operators in staying informed about the machine's condition and significantly enhances reliability.

Ergonomically designed controls on both models ensure that users can operate them with minimal strain, promoting comfort during extended use. Additionally, their compact design allows for easy storage and transport, making them an excellent choice for businesses with diverse cleaning needs.

In terms of safety, both SCC326 and SC326 are fitted with automatic shut-off systems that activate in case of emergencies, thereby protecting users and equipment alike. This attention to safety standards reflects Windsor's commitment to providing top-tier cleaning solutions.

Ultimately, the Windsor SCC326 and SC326 series embody a blend of power, efficiency, and safety, catering to the rigorous demands of industrial cleaning tasks. Whether addressing large-scale surface areas or caring for intricate spaces, these models are engineered to deliver superior performance without compromising ease of use or environmental responsibility.
Top Page Image Contents