Windsor SC20T, SCX20T To Adjust Squeegee Pitch, To Adjust Amount of Rear Squeegee Deflection

Page 26

MAINTENANCE

TO ADJUST SQUEEGEE PITCH

1.Choose a smooth, level surface. Turn “ON” the key switch and vacuum switch. Lower the squeegee and drive forward at least 2 feet (60cm.).

2.With the squeegee down, stop the machine. Do not allow machine to roll back.

FOR SAFETY: Before leaving or servicing the machine, stop on level surface, turn off machine and remove key.

3.Determine the differences, if any, in deflection of the squeegee blade between each end and the middle. Proper adjustment is obtained when deflection is equal all the way across the squeegee blade.

4.To decrease the deflection of the squeegee blade at the ends, adjust plastic knobs at the far right or left of squeegee assembly.

5.Check the deflection of the squeegee blades again. Repeat steps 1 through 4 until the deflection is equal across the entire rear squeegee blade.

TO ADJUST AMOUNT OF REAR SQUEEGEE DEFLECTION

1.Choose a smooth, level surface. Turn “ON” the key switch and vacuum switch. Lower the squeegee and drive forward at least 2 feet (60cm.).

2.With the squeegee down, stop the machine. Do not allow machine to roll back.

FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine and remove key.

3.Observe the amount of squeegee deflection. It should deflect approximately 3/8 in. (9.5mm) across the entire width of the squeegee.

4.To increase the squeegee deflection, turn the center knob above the lift carrier bracket clockwise. To decrease the deflection, turn the knob counterclockwise.

NOTE: The deflection should be consistent along the length of the squeegee. If the deflection varies from end to end the knobs can be adjusted independently to correct the variation.

5.Turn on the key switch. Raise, then lower squeegee assembly. Drive forward at least 2 feet (60cm).

6.Repeat steps 2 through 4 until deflection of approximately 3/8 in. (9.5mm) is reached.

TO REPLACE OR ROTATE REAR SQUEEGEE BLADE

1.With the squeegee in the up position, turn key switch “OFF”.

FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine and remove key.

2.Remove the squeegee assembly from the machine. Unlatch and remove blade retainer strap and remove squeegee blade.

3.Rotate the squeegee to new edge position or replace as required. Each blade has four edge positions.

4.Install blade on locating tabs of squeegee assembly.

5.Install squeegee retainer strap.

6.Fasten and lock latch, adjust latch only tight enough to take up slack in retaining strap.

TO REPLACE OR ROTATE FRONT SQUEEGEE BLADE

1.With the squeegee in the up position, turn key switch “OFF”.

2.Remove the squeegee from the machine. Loosen (3) thumb screws securing retainer strap.

3.Remove front retainer strap.

4.Remove squeegees blade from locating tabs on squeegee assembly and rotate to new position or replace as required.

5.Install blade on locating tabs of squeegee tool.

6.Replace front retainer strap.

7.Secure strap by tighten (3) thumb screws.

GREASING AXLES

1.Apply 1-2 strokes of MOBILTEMP→78 or compatible clay-based or calcium-based grease per service schedule.

4-7

SABER (SC) 86038350 01/29/07

 

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Walk Behind Scrubber Overview Machine Data LOG/OVERVIEWYour Dealer Table of Contents HOW to USE this Manual ModelImportant Safety Instructions Read ALL Instructions Before Using this MachineHazard Intensity Level Hazard Intensity LevelSafety Label Location Safety Decal 86252530 PRV noTechnical Specifications DIMENSION/CAPACITYSpecial Notes MeasureHOW the Machine Works Components Controls NON-TRACTION Hour Meter Optional Brush SwitchControls NON Traction Circuit BreakersControls Traction KEY Switch Propel Buttons Normally ForwardEmergency SHUT-OFF Switch Optional Machine Operation Double Scrub To Begin ScrubbingTo Stop Scrubbing Emptying and Cleaning Tanks Solution TankMaintenance BatteriesMaintenance + red Blk Uncoated Floors Replacing or Installing Scrub BrushesScrub Brushes Finished FloorsMaintenance Squeegee Blades To Remove Squeegee AssemblyAdjusting Deluxe Squeegee To Replace Squeegee BladesTo Replace or Rotate Rear Squeegee Blade To Adjust Squeegee PitchTo Adjust Amount of Rear Squeegee Deflection To Replace or Rotate Front Squeegee BladeMaintenance Service Schedule HRSMachine Troubleshooting Problem CauseProblem Cause Solution

SC20T, SC20, SCC20, SCXC20T, SCX20T specifications

Windsor SCC20, SC20, SCC20T, SCX20T, and SC20T represent a remarkable range of innovative cleaning equipment designed primarily for commercial and industrial use. These models, known for their rugged build and advanced technology, cater to various surface cleaning needs in settings like warehouses, retail spaces, and factories.

One of the standout features of the Windsor SCC20 series is its powerful cleaning capability. The machines are equipped with high-performance vacuum motors that ensure effective suction, allowing for the collection of dirt, debris, and moisture in one pass. This efficiency not only saves time but also enhances the overall cleaning experience. The SC20T and SCC20T variants take this efficiency further with their upgraded features, enabling them to handle even tougher grime and larger debris with ease.

In terms of technology, the Windsor models integrate user-friendly controls and ergonomic designs. The adjustable handle ensures comfort during prolonged use, while the intuitive control panel simplifies operation, allowing staff to operate the machines without extensive training. The SCC20T and SCX20T further boast advanced filtration systems, capturing airborne particulate matter, which is crucial for maintaining a healthier working environment.

Another critical characteristic is the durability of these machines. Built with robust materials and designed to withstand harsh conditions, the SCC20 series is particularly favored in high-traffic areas. Maintenance is also user-friendly, with easy-access ports for troubleshooting and quick repairs. This feature significantly reduces downtime during cleaning operations, making them reliable partners in maintaining cleanliness.

Windsor's commitment to environmental sustainability is evident in its cleaner formulations and energy-efficient motors. The SCC20 and related models operate with reduced noise levels, which is particularly beneficial in settings where noise pollution is a concern.

In summary, the Windsor SCC20, SC20, SCC20T, SCX20T, and SC20T are standout cleaning solutions characterized by their powerful performance, user-friendly design, and durability. With advanced technologies aimed at increasing efficiency and maintaining a healthier workspace, these models exemplify Windsor's dedication to delivering top-tier cleaning equipment that meets the diverse needs of various industries. Whether for daily maintenance or deep cleaning tasks, the SCC20 series provides a comprehensive approach to effective cleaning solutions.
Top Page Image Contents