Windsor cdt7 10080220 manual Maintenance, Vacuum Motor Carbon Brushes Replacement Windsor

Page 20
Vacuum Motor Carbon Brushes Replacement (Windsor)
Wire Terminal

MAINTENANCE

ONLY QUALIFIED

! WARNING: MAINTENANCE

PERSONNEL ARE TO

PERFORM THE FOLLOWING REPAIRS. VACUUM MOTOR REPLACEMENT

1.Turn off all switches and unplug machine.

2.Remove recovery tank.

3.Remove the (2) screws that fasten the solution tank to the frame, and tilt tank back to expose the inside of the frame.

4.Locate the vacuum motor wires and disconnect at the connector. Close the solution tank.

5.Remove the (6) screws holding the vacuum motor cover (p/n 27809) to the solution tank.

6.Remove the vacuum motor.

7.Reverse process to install vacuum motor.

Vacuum Motor Carbon Brushes Replacement (Windsor)

 

End Cap

Carbon

WARNING: The green

Brushes

ground wire must be

 

attached for safe operation.

 

See wiring diagram.

If armature commutator is grooved, extremely pitted or not concentric, the motor will need to be replaced or sent to a qualified service center.

Important:

These brushes wear quicker as the length shortens due to increased heat. Spring inside brush housing will damage motor if brushes are allowed to wear away completely.

WARNING: The green 38 [9.5mm]

Periodically check the length of the carbon brushes. Replace both carbon brushes when either is less than 3/8" (9.5mm) long.

Vacuum Motor Carbon Brushes Replacement (Ametek)

 

End Cap

Carbon

WARNING: The green

Brushes

ground wire must be

 

attached for safe operation.

 

See wiring diagram.

Note: When replacing carbon brushes loosen wire terminal BEFORE removing screws on bracket.

Wire

Terminal

Note:

Place stop in groove.

If armature commutator is grooved, extremely pitted or not concentric, the motor will need to be replaced or sent to a qualified service center.

Important:

These brushes wear quicker as the length shortens due to increased heat. Spring inside brush housing will damage motor if brushes are allowed to wear away completely.

Vacuum Motor Carbon Brushes Replacement (Ametek) 3/8 (9.5mm)

Periodically check the length of the carbon brushes. Replace both carbon brushes when either is less than 3/8" (9.5mm) long.

4-3

CADET 86038220 03/16/07

Image 20
Contents Operating Instructions MODEL CDT7CARPET EXTRACTOR Read these instructions before operating the machineMACHINE DATA LOG/OVERVIEW YOUR DEALERMODEL PUBLISHEDTABLE OF CONTENTS HOW TO USE THIS MANUALSAFETY MAINTENANCEHOW TO USE THIS MANUAL MODELSAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING THIS MACHINEThis machine is for commercial use To reduce the risk of fire, electric shock, or injuryHAZARD INTENSITY LEVEL HAZARD INTENSITY LEVELFOR SAFETY WHEN SERVICING MACHINEGROUNDING INSTRUCTIONS GROUNDING INSTRUCTIONSELECTRICAL TECHNICAL SPECIFICATIONS POWER TYPEGENERAL DIMENSIONS/WEIGHT SOLUTION CAPACITY 7 gallons 26.5ltrCONTROLS/COMPONENT LOCATIONS 6. Recovery Tank Dome 1. Solution Intake Cover 2. Vacuum Intake Cover 3. Float Shut-Off 4. Clean-Out Opening 5. Pour Spout 6. Lift HandleCHEMICALS FILLING OPERATIONSCADET 86038220 03/16/07 INCORRECT OPERATIONSCORRECT INTERMITTENT CONTINUOUS CLEANING PROCEDURE OFFOFF OFF PUMPVACUUM ONON OFF ACCESSORY TOOL USAGE3-10 MAINTENANCE SERVICE SCHEDULE MAINTENANCEDAILY WEEKLYDAILY / REGULAR MAINTENANCE MAINTENANCEPERIODIC MAINTENANCE Vacuum Motor Carbon Brushes Replacement Windsor Vacuum Motor Carbon Brushes Replacement AmetekWARNING The green WARNING The greenONLY QUALIFIED WARNING MAINTENANCE PERSONNEL ARE TO PERFORM THE FOLLOWING REPAIRS BELT REPLACEMENTSOLUTION PUMP REPLACEMENT WIRING DIAGRAM 8626845086268830 86266890 PRV NO 86004480 PRV NOTROUBLESHOOTING CHART PROBLEMSOLUTION CAUSETHIS PAGE INTENTIONALLY LEFT BLANK A B FRAME ASSEMBLYSEE SOLUTION TANK FRAME ASSEMBLY BRUSH ASSEMBLY 44451743 3741BRUSH ASSEMBLY PUMP ASSEMBLY C SEE SOLUTION 5 TANKPRIOR TO SERIAL NO 1120 2625PUMP ASSEMBLY FROM SERIAL NO SEE SOLUTION TANK 2427PUMP ASSEMBLY VACUUM SHOE ASSEMBLY 5-10 5-11 CONTROL PANEL ASSEMBLYSEE SOLUTION TANK 5-12 SOLUTION TANK ASSEMBLY 5-13PANEL SEE FRAME5-14 5-15 RECOVERY TANK ASSEMBLY10A 1A 14A 5-16 SUGGESTED SPARE PARTS 5-17