Wayne-Dalton 9700 Installation, Tracks, Flagangle Vertical Track, Quick Install TAB Unlocked

Page 7

Installation

Begin the installation of the door by checking the opening. It must be the same size as the door. Vertical jambs must be plumb and the header level. Side clearance, from edge of door to wall, must be minimum of 3-1/2” (89mm) on each side.

IMPORTANT: Stainless steel or PT 2000 coated lag screws (not supplied) MUST be used when installing center bearing brackets, end brackets, jamb brackets, operator mounting/support brackets and disconnect brackets on treated lumber (preservative-treated). Stainless steel or pt 2000 lag screws are NOT necessary when installing products on untreated lumber.

NOTE: It is recommended that 5/16” lag screws be pilot drilled using a 3/16” drill bit prior to fastening.

IMPORTANT: When installing 5/16” diameter lag screws using an electric drill/driver, the drill/driver’s clutch must be set to deliver no more than 200 in. lbs. of torque. Fastener failure could occur at a higher setting.

NOTE: Insulated glass will cause the top section to be significantly heavier than the remaining sections. Wayne-Dalton attempts to balance the door at the top & bottom. To prevent any sudden door acceleration between the top & bottom, we recommend motor operating all glazed top doors. Doors with insulated glass top sections should not be manually operated.

1

Tools Needed:

None

Attaching Flagangles to Vertical

Tracks

If you have fully adjustable flagangles: Hand tighten the flagangle to the vertical track using a stud plate and (2) 1/4” - 20 flange hex nuts. Repeat for other side.

Secure the flange nuts after flagangle spacing is completed in Step 11.

If you have quick install flagangles:

Place the lower quick install tab of the flagangle in the quick install feature of the vertical track. Give the flagangle 1/4 turn to lock in place. Repeat for other side.

flagangle

(2)1/4”- 20 flange hex nuts

Stud Plate

Vertical track

quick install flagangle

FLAGANGLE

VERTICAL

TRACK

Fully Adjustable Flagangle

QUICK INSTALL TAB UNLOCKED

QUICK INSTALL TAB LOCKED

 

 

 

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your

7

local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com

 

 

Image 7
Contents Important Notice 9700Table of Contents Package Contents Endstile Each section except top sectionUsed to identify each section Labels on each end stileRemoving An Existing Door Tools RequiredTrack Type MIN. Headroom Preparing the OpeningHeadroom requirement Backroom requirementFlagangle Vertical Track InstallationQuick Install TAB Unlocked TracksHorizontal Angles Installing Jamb BracketsTools Needed Hammer Bottom Section DrumsTools Needed None Flagangle Cable Vertical Track Assembly Jamb Bracket Bottom SectionVertical Tracks Stacking SectionsSelf Tapping Screws BarOperator Bracket TOP Bracket Slide Top BracketsTop Section RollerTruss Head Bolt Tion Causing Severe or FatalFlagangles Horizontal TrackTorqueMaster Spring Tube Adjusting Top BracketsTools Needed Wrench Step Ladder Center Bracket Bushing Center Bracket AssemblyCenter Bracket Bushing 2 Wraps Cable Drums/ Drum WrapsRatchet wheel is required on the left Securing Center Bracket AssemblyEnd Brackets Wrench Socket Driver Step LadderSecuring Door For Spring Winding Cable AdjustmentTools Needed Vice Clamps Winding the TorqueMaster Winding SpringsIt is recommended that Leather gloves be worn whileImportant Mark number of spring Securing Drum WrapsTurns on TorqueMaster Plus end bracket Cause severe or fatal injury Rear SupportRaising door further can Result in door fallingNumber of Turns Shown on Spring Turn ChartFull Tension of the Spring Wheel from the RecommendedInstructions TorqueMaster Plus ResetPawl TorqueMaster Plus Reset InstructionsChecking Springs for Tension Balancing DoorPawl knob in upper Position Place vice clamps Above 3rd Roller on both vertical trackAttached to Track Pawl knob in Lower PositionNo Scew EYE Pull Rope Bottom Bracket Pull RopeJamb approximately 48 to 50 1220 to As shownFailure to Test or Make ANY Trolley OperatorMAY Result in Severe or Fatal Injury Important do not USE a Pressure Washer on Your Garage Door CleaningAcrylic Cleaning Instructions PaintingPainting You Lifetime Limited Warranty ModelThank you for your purchase
Related manuals
Manual 2 pages 15.21 Kb Manual 18 pages 29.29 Kb Manual 4 pages 60.02 Kb Manual 2 pages 14.43 Kb

9700 specifications

Wayne-Dalton is a well-known brand in the garage door industry, offering a wide range of models designed for durability, performance, and aesthetic appeal. Among its most popular series are the 9700, 5000, 8000, 9000, and 9800, each equipped with unique features and advanced technologies to meet diverse customer needs.

The Wayne-Dalton 9700 series is known for its combination of strength and insulation. This garage door is manufactured with a three-layer construction providing robust protection against the elements while offering excellent energy efficiency. The insulated steel construction can help maintain interior temperatures, making it ideal for attached garages.

The 5000 series, on the other hand, is designed for a more traditional look combined with modern performance. Featuring a lightweight design, it is made from durable materials that resist rust and corrosion. The 5000 series can be customized with different colors and styles, allowing homeowners to achieve the perfect aesthetic to enhance their property.

Moving on to the 8000 series, this model is designed for commercial applications and residential use where heavy-duty functions are necessary. It is built to withstand extreme weather conditions while providing optimal security with added strength features. The 8000 series offers smooth operation and minimal maintenance requirements, making it a great choice for those seeking reliability.

The 9000 series stands out with its stylish design and sleek finishes. This series offers advanced insulation options, coupled with numerous panel designs that provide a polished and sophisticated look. The 9000 model emphasizes both aesthetics and energy efficiency, making it a favorite among homeowners looking for a beautiful yet functional garage door.

Lastly, the 9800 series is the premium option within Wayne-Dalton’s offerings. This series is characterized by its high insulation value and thermal efficiency, thanks to its innovative construction techniques. The 9800 doors can be customized with numerous panel options and colors, delivering a luxury look while ensuring excellent performance.

In conclusion, Wayne-Dalton’s 9700, 5000, 8000, 9000, and 9800 series garage doors each feature distinctive characteristics and technologies aimed at enhancing durability, security, and aesthetics. Homeowners can find a reliable option within this range that suits their specific requirements, whether they prioritize insulation, style, or heavy-duty functionality. With Wayne-Dalton’s commitment to quality and innovation, these garage doors stand out in today’s market.