Wayne-Dalton 9700 Flagangles, Tion Causing Severe or Fatal, Horizontal Track, Truss Head Bolt

Page 14

12

Attaching Horizontal Tracks to

 

Flagangles

Tools Needed:

If you have fully adjustable flagangles:

9/16” Socket

To install horizontal track, place the curved

end over the top roller. Align the bottom of

 

7/16” Socket

the horizontal track with the vertical track.

Ratchet Wrench

Hand tighten the horizontal track to the

flagangle with (2) 1/4”-20 x 9/16” track

 

9/16” Wrench

bolts and (2) 1/4” - 20 flange hex nuts.

Level

Repeat for other side.

WARNING

Step Ladder

DO NOT RAISE DOOR UNTIL

HORIZONTAL TRACKS ARE SE­

CURED AT REAR, AS OUTLINED

IN STEP 23, OR DOOR COULD

FALL FROM OVERHEAD POSI­

TION CAUSING SEVERE OR FATAL

INJURY.

Level the horizontal track assembly and bolt the horizontal angle to the slot in the flagangle using (1) 3/8” - 16 x 3/4” truss head bolt and (1) 3/8” - 16 hex nut. Repeat for other side.

NOTE: If an idrive® opener will be installed, position horizontal tracks slightly above level.

Remove the nail that was temporarily holding the top section in place, installed in Step 11.

IMPORTANT: Failure to remove nail before attempting to raise door could cause permanent damage to top section.

If you have quick install flagangles: Align key slot of the horizontal track with the quick install tab of the flagangle. Push curved portion of horizontal track down to lock in place.

WARNING

DO NOT RAISE DOOR UNTIL

HORIZONTAL TRACKS ARE SE­

CURED AT REAR, AS OUTLINED

IN STEP 23, OR DOOR COULD

FALL FROM OVERHEAD POSI­

TION CAUSING SEVERE OR FATAL

INJURY.

Level the horizontal track assembly and bolt the horizontal angle to the slot in the flagangle using (1) 3/8” - 16 x 3/4” truss head bolt and (1) 3/8” - 16 hex nut. Repeat for other side.

NOTE: If an idrive® opener will be installed, position horizontal tracks slightly above level.

Remove the nail that was temporarily holding the top section in place, installed in Step 11.

IMPORTANT: Failure to remove nail before attempting to raise door could cause permanent damage to top section.

flagangle

HORIZONTAL TRACK

 

1/4”-20 x 9/16”

 

Track Bolts

1/4”-20 flange

 

hex nuts

Vertical Track

fully adjustable flagangles

Flagangle

Flagangle

Horizontal

Horizontal

track

track

 

Key slot

QUICK

INSTALL

 

TAB

QUICK

 

INSTALL

Key slot

TAB

 

Vertical

Vertical

track

track

quick install flagangles

3/8” - 16 X 3/4”

TRUSS HEAD BOLT

3/8” - 16 Hex nut

Horizontal ANGLE

HORIZONTAL TRACK

14Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your

local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com

Page 13 Page 15
Image 14
Page 13 Page 15
Contents 9700 Important NoticeTable of Contents Package Contents Labels on each end stile Each section except top sectionUsed to identify each section EndstileTools Required Removing An Existing DoorBackroom requirement Preparing the OpeningHeadroom requirement Track Type MIN. HeadroomTracks InstallationQuick Install TAB Unlocked Flagangle Vertical TrackTools Needed Hammer Installing Jamb BracketsHorizontal Angles Tools Needed None DrumsBottom Section Stacking Sections Vertical Track Assembly Jamb Bracket Bottom SectionVertical Tracks Flagangle CableBar Self Tapping ScrewsOperator Bracket Roller Top BracketsTop Section TOP Bracket SlideHorizontal Track Tion Causing Severe or FatalFlagangles Truss Head BoltTools Needed Wrench Step Ladder Adjusting Top BracketsTorqueMaster Spring Tube Center Bracket Bushing Center Bracket AssemblyCenter Bracket Bushing Cable Drums/ Drum Wraps 2 WrapsWrench Socket Driver Step Ladder Securing Center Bracket AssemblyEnd Brackets Ratchet wheel is required on the leftTools Needed Vice Clamps Cable AdjustmentSecuring Door For Spring Winding Leather gloves be worn while Winding SpringsIt is recommended that Winding the TorqueMasterTurns on TorqueMaster Plus end bracket Securing Drum WrapsImportant Mark number of spring Result in door falling Rear SupportRaising door further can Cause severe or fatal injuryWheel from the Recommended Spring Turn ChartFull Tension of the Spring Number of Turns Shown onTorqueMaster Plus Reset InstructionsBalancing Door TorqueMaster Plus Reset InstructionsChecking Springs for Tension PawlPawl knob in Lower Position Place vice clamps Above 3rd Roller on both vertical trackAttached to Track Pawl knob in upper PositionAs shown Pull RopeJamb approximately 48 to 50 1220 to No Scew EYE Pull Rope Bottom BracketMAY Result in Severe or Fatal Injury Trolley OperatorFailure to Test or Make ANY Painting CleaningAcrylic Cleaning Instructions Important do not USE a Pressure Washer on Your Garage DoorPainting Lifetime Limited Warranty Model YouThank you for your purchase
Related manuals
Manual 2 pages 15.21 Kb Manual 18 pages 29.29 Kb Manual 4 pages 60.02 Kb Manual 2 pages 14.43 Kb

9700 specifications

Wayne-Dalton is a well-known brand in the garage door industry, offering a wide range of models designed for durability, performance, and aesthetic appeal. Among its most popular series are the 9700, 5000, 8000, 9000, and 9800, each equipped with unique features and advanced technologies to meet diverse customer needs.

The Wayne-Dalton 9700 series is known for its combination of strength and insulation. This garage door is manufactured with a three-layer construction providing robust protection against the elements while offering excellent energy efficiency. The insulated steel construction can help maintain interior temperatures, making it ideal for attached garages.

The 5000 series, on the other hand, is designed for a more traditional look combined with modern performance. Featuring a lightweight design, it is made from durable materials that resist rust and corrosion. The 5000 series can be customized with different colors and styles, allowing homeowners to achieve the perfect aesthetic to enhance their property.

Moving on to the 8000 series, this model is designed for commercial applications and residential use where heavy-duty functions are necessary. It is built to withstand extreme weather conditions while providing optimal security with added strength features. The 8000 series offers smooth operation and minimal maintenance requirements, making it a great choice for those seeking reliability.

The 9000 series stands out with its stylish design and sleek finishes. This series offers advanced insulation options, coupled with numerous panel designs that provide a polished and sophisticated look. The 9000 model emphasizes both aesthetics and energy efficiency, making it a favorite among homeowners looking for a beautiful yet functional garage door.

Lastly, the 9800 series is the premium option within Wayne-Dalton’s offerings. This series is characterized by its high insulation value and thermal efficiency, thanks to its innovative construction techniques. The 9800 doors can be customized with numerous panel options and colors, delivering a luxury look while ensuring excellent performance.

In conclusion, Wayne-Dalton’s 9700, 5000, 8000, 9000, and 9800 series garage doors each feature distinctive characteristics and technologies aimed at enhancing durability, security, and aesthetics. Homeowners can find a reliable option within this range that suits their specific requirements, whether they prioritize insulation, style, or heavy-duty functionality. With Wayne-Dalton’s commitment to quality and innovation, these garage doors stand out in today’s market.
Top Page Image Contents