Wayne-Dalton 347610 Door Arm Hookup, Lift Handles, Pull Down Rope, Tools Needle nose pliers

Page 17

Optional Installation

Door Arm Hookup

Tools: Needle nose pliers

At the center of the top section, measure horizontally from the top of center hinge to the bottom of strut. Using that dimension, measure and cut (2) pieces of perforated angles. Assemble the

(2)pieces together using (2) 3/8” bolts and nuts (supplied by others). Now, secure to the top section using carriage bolts and nuts (supplied by others), thru bolt both the perforated angles to the top section, as shown.

Align the door arm with hole with one of the holes in the perforated angles. Secure the door arm to the perforated angle using (1) 5/16” – 18 x 1” hex head bolt and (1) 5/16” – 18 lock nut (supplied by others), as shown.

Strut

 

 

 

(2) 3/8” Hex bolt

Top

 

(1) 5/16” Hex bolt

and lock nut

section

Carriage bolt

and lock nut

(supplied by others).

 

and nuts

(supplied by others).

 

 

(supplied by

 

(2) Perforated

 

others)

 

angles

 

 

 

 

 

Center hinge

Typical

 

 

 

 

 

 

door arm

Lift Handles

Tools: Power drill, 1/8” Drill bit, Tape measure

NOTE: Lift handles must be lined up vertically. Bottom Section:

Locate the exterior center stile or center most stile on the bottom section.

NOTE: For flush doors, find the center most stile by locating the center most hinge.

Using the bottom hole of the lift handle, measure up 3” from the bottom of bottom section. Mark the hole locations and drill (2) 9/32” dia. holes through the bottom section. On the outside of the door, insert (2) 1/4” - 20 x 2 1/2” carriage bolts (black head) into the outside lift handle and insert the assembly into the (2) pre-drilled holes in the bottom section. From the inside, slide the

(2)holes in the inside lift handle over the stems of the carriage bolts. Secure the outside and inside lift handle to the bottom section with (2) 1/4” – 20 flange hex nuts.

Intermediate I Section:

Locate the exterior center stile or center most stile on the Intermediate I section. Mark a vertical line on the section at that point.

NOTE: Some Garage Doors may require both lift handles to be installed on bottom section. If your bottom section height is 28” or 29”, install both lift handles onto the bottom section. Install bottom lift handle per above instructions, then install the second lift handle a Minimum of 20” and a Maximum of 30” above the bottom lift handle.

Measure up 4” from the bottom of the Intermediate I section. Using this measurement as a guide, position the bottom hole of the lift handle bottom at the mark. Make a mark at the top hole of the lift handle. This should give you a Minimum of 20” and a Maximum of 30” between the lower lift handle and the middle of the top lift handle. If needed, reposition the lift handle to stay within the Minimum and Maximum dimensions, as stated above.

Using the lift handle as a template, mark the hole locations and drill (2) 9/32” dia. holes through the section. On the outside of the door, insert (2) 1/4” - 20 x 2 1/2” carriage bolts (black head) into the outside lift handle and insert the assembly into the (2) pre-drilled holes in the section. From the inside, slide the (2) holes in the inside lift handle over the stems of the carriage bolts. Secure the outside and inside lift handle to the section with (2) 1/4” – 20 flange hex nuts.

 

Lift

(2) 1/4” - 20 x 2 1/2”

 

Carriage bolts and (2) 1/4” – 20

Intermediate I

handle

Flange hex nuts

 

 

section

 

 

 

 

Center

Bottom

 

hinge

Lift

 

section

(2) 1/4” - 20 x 2 1/2”

 

handle

 

 

Carriage bolts and (2) 1/4” – 20

Strut

 

Flange hex nuts

 

3”

 

Pull Down Rope

Tools: Power drill, 1/8” Drill bit, Tape measure

WARNING

Do not install pull down rope on doors with operators. Children may become entangled in the rope causing severe or fatal injury.

Measure and mark the jamb approximately 48” to 50” (1220 to 1270 mm) from floor on the right or left side of jamb. Drill 1/8” pilot hole for no. 6 screw eye. Tie the pull down rope to the no. 6 screw eye and to the bottom corner bracket, as shown.

 

No. 6 Screw eye

 

Typical bottom

 

corner bracket

48” to 50”

Pull down

From floor

rope

 

Pull

 

down

 

rope

 

17

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer,

refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com

Page 16 Page 18
Image 17
Page 16 Page 18
Contents B l e O f C o n t e n t s 7000/7400 SeriesStacked Sections C1. Top Section Graduated End HingesPackage Contents Important Safety Instructions Tools RequiredGraduated End Hinge Strut Identification Door Section IdentificationPreparing the Opening Removing an Existing DoorRail of the bottom section Headroom RequirementsHeader board 2x Lumber preferred Min. side HeadroomRoom Clearance for Track isPage Strutting Track Roller CarriersRepeat the same process for the right hand side For 2 Long Strut ApplicationsTop Fixtures Half Center HingesStacking Sections Bottom SectionVertical Tracks Horizontal Tracks Adjusting Top FixturesTop Section For Center Hinges and or half center hingesAdjusted for each side Torsion Spring AssemblyEnd Bearing Brackets Center BracketTorsion Spring Attachment For Doors with a Coupler AssemblyTools Step Ladder, 1/2 Wrench If your door came with a Center Bracket BushingTools Vice Clamps Set CollarsRear Back Hangs Winding SpringsSpring Set screws Approved Torsion shaft Winding cone16-18 x 1-1/4 Parallel to door Label PlacementCeiling member Door Arm Hookup Tools Power drill, 1/8 Drill bit, Tape measureLift Handles Pull Down RopeOperation and Maintenance Cleaning Your Garage DoorPainting Your Garage Door Clear Or Stained FinishesPage Limited warranty Model 7000 and 7400 Series Warranty

347610 specifications

Wayne-Dalton 347610 is a prominent overhead garage door model known for its blend of durability, functionality, and aesthetic appeal. Specifically designed to cater to residential needs, this garage door offers a reliable solution for homeowners seeking a balance of performance and style.

One of the main features of the Wayne-Dalton 347610 is its robust construction. The door is made from high-quality materials, which ensures longevity and resistance to wear and tear. Its design often incorporates reinforced insulation, which is not only energy-efficient but also aids in noise reduction. Homeowners appreciate this added quality, particularly in regions with extreme temperatures.

Another noteworthy characteristic of the Wayne-Dalton 347610 is its versatility in design options. The door comes in various colors, styles, and panel configurations, allowing homeowners to choose a look that complements their home’s architecture. This personalization enhances curb appeal while still offering the functionality expected from a modern garage door.

In terms of technology, this model features Wayne-Dalton’s innovative TorqueMaster Plus spring system. This patented technology increases safety and convenience by allowing for easy installation and maintenance. The system is designed to eliminate the need for exposed springs, reducing the risk of injury and providing a cleaner, more refined appearance.

The Wayne-Dalton 347610 is also equipped with advanced weather sealing, which ensures your garage remains protected from the elements. This feature is particularly beneficial in preventing water leaks, drafts, and pests from entering the garage, giving homeowners peace of mind.

Moreover, the door supports various operational mechanisms, including manual and electric options. Electric models are compatible with several types of garage door openers, ensuring smooth and reliable functionality. The integration of smart technology in some versions allows for remote access and monitoring via smartphones or smart home systems, enhancing convenience for tech-savvy homeowners.

Overall, the Wayne-Dalton 347610 is a well-rounded garage door solution. Its combination of quality construction, aesthetic versatility, innovative technology, and enhanced security features makes it an excellent choice for homeowners looking to invest in a reliable and stylish garage door. Whether for new builds or replacement projects, this model stands out as a top contender in the residential garage door market.
Top Page Image Contents