Viper VR-6000 owner manual Vacuum Pump, Oil top-up

Page 22

INSTRUCTIONS MANUAL

blanket (i) from the storage tank (do not touch or disconnect the wires of the heater blanket).

Extreme care must be taken when removing the storage tank, so as to avoid pulling wires loose and damaging the copper tubing.

Remove the storage tank (f) from its seat, leaving the heater blanket around the scale plate. Rest the storage tank on a stand at least 10” in height. Switch on the MACHINE. Be careful not to touch any electrical wires. Wait at least 10 seconds and press STOP to silence the alarm. Press the INCREASE and ARROW keys simultaneously and hold down for about 5 seconds. The value displayed at this point will correspond to the scale zero value. Press down lightlyon the scale plate; the value should increase. If it does not, replace the charge cell. Press the ENTER key to memorize the value. In this phase, take care that nothing touches the scale plate). Place the reference weight (50 lbs) carefully at the center of the scale plate and check that the displayed value increases accordingly. Press the SEL keyand use the INCREASE & ARROW keys to type in the 4 figures of the reference weight. Press ENTER. The display reading should be the reference weight minus the weight of the empty bottle (tare weight).

Remove the reference weight. Switch off the machine and disconnect from main power supply. Replace the storage tank in its seat on the scale plate. Switch on the MACHINE, taking care not to touch any electrical wires. Check calibration: place a known reference weight on the bottle and check that the displayed availability value increases by the value of the known reference weight ±2%. Remove the reference weight. Switch off the machine and disconnect from main supply. Replace the storage tank locking bolts. Open the red and blue storage tank valves. Replace the rear plastic cover.

NOTE: In order to check the scale calib ration the unit must b e displaying a positive value for REFRIGERANT AVAILABLE, if the display is reading zero additional weight must b e added to the top of the tank to get a positive reading. The known weight is then added and the change in weight is verified as the known weight.

VACUUM PUMP

Perform the operations listed below on a routine basis in order to ensure good operation of the vacuum pump.

M.1) Oil top-up

M.2) Oil change

M.3) Decontamination

When topping-up or replacing the pump oil, use only VIPER No. 793091 Vacuum Pump Oil.

M.1) Oil top-up

This operation must be performed when the level of the oil falls to less than half on the indicator (4 - Figure 15). To refill the oil, perform the steps listed below in the order given. Refer to Figure 13.

1.Disconnect the VR-6000from main power supply.

2.Unscrew the filling cap (3).

3.Pour oil into the tank until the oil level is about half on the indicator (4).

4.Replace the oil cap (3) and tighten down.

M.2) Oil change

The vacuum pump oil must be replaced once a season and in any case every time the refrigerant filters are replaced. The oil must also be changed whenever it changes color, becoming dark and turbid, since this is a sign that it has been contaminated and has absorbed humidity. Before beginning the oil change procedure, procure a container of

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents VR-6000 Instructions Manual Index Safety Summary Safety InformationMotion Hazards Electrical Shock HazardsFume Hazards HEAT/FREEZING Hazards Additional Safety InformationEXPLOSION/FLAME Hazards General About the Viper A/C AIR Conditioning Service CenterIntroduction CertificationMachine Basic ComponentsPage Controls and Control System Control PanelFunction Selector Keyboard Status and Alarm Panel Front viewsPreparation for USE Measurement SettingViper VR-6000 Specifications PreparationPage Page Operation Instructions Recover and Recycle Refrigerant from AN AC SystemRemoving NON-CONDENSABLE Gases Normal R-134 container pressure chart Vacuum Phase Recharge AN A/C SystemRecovering the Refrigerant in the Hoses Maintenance Replacing Refrigerant FILTER/DRYERCase Care AIR Conditioning Hose MaintenanceEmptying the Used OIL Tank Calibrating the Electronic ScaleVacuum Pump Oil top-upPage No Display When Main Power Switch is on TroubleshootingRecovery Problems Refilling does not FlowMANUFACTURER’S Limited Warranty To Obtain Services Under this WarrantyTransférer Duréfrigérant Neuf Dans LA Bouteille DE Stockage Résumé DES Normes DE Sécurité Informations SUR LasécuritéRisque DE Décharge Électrique Risques Liés AU MouvementRisques Liés À LA CHALEUR/AU Froid Risques DE FuméesRisques D’EXPLOSION / Incendie Généralités Informations Supplémentaires SUR LasécuritéInformations SUR CE Manuel LA Machine Composants FondamentauxPage Commandes ET Voyants Tableau de commandeClavier de sÉlection des fonctions Panneau Voyants ET Alarmes Entrée Mesures Préparation À L’EMPLOIPréparation Page Page Instructions Pour LES Interventions RÉCUPÉRATION/RECYCLAGE DE Réfrigérant D’UN Système A/CPurge DES GAZ NON Condensables Phase DE Vide Table pression réservoir R-134Recharge D’UN Système A/C Injection Huile NeuveRemplacement DES Filtres Déshydrateurs Récupération DU Réfrigérant Dans LES Tuyaux FlexiblesManuel D’INSTRUCTIONS LE Soin DU CAS Maintenance DES Tuyaux Flexibles A/CVidange DU Récipient D’HUILE Usée Étalonnage DE Labalance ÉlectroniquePage Vidange huile Problèmes DE RécupérationRemplacement DES Filtres Déshydrateurs LE Remplissage NE Circule PASPour Obtenir LES Services Prévus PAR Cette Garantie Garantie Limitée DU FabricantSumario Seguridad Informaciones DE SeguridadPartes EN Movimiento Choque EléctricoHumos Quemaduras Y Congelamiento Información Adicional Sobre SeguridadExplosión E Incendio Certificación IntroducciónGeneralidades Acercade Este ManualLA Máquina Elementos FundamentalesPage Sistemade Mando Y Control Panel de controlTeclado DE Selección DE Operaciones Descarga DE AceiteTablero DE Estado Y Alarmas Ajuste DE Unidad DE MedidaPreparación Puesta EN ServicioDatos DEL Viper VR-6000 Preparar LA Bombona DE Almacenamiento DE RefrigerantePage Page Eliminar Gases no Condensables Tabla de presiones R-134 chart Fase DE VacíoIntroducir Aceite Nuevo Recargar UN Sistemade A/CRecuperar EL Refrigerante DE LOS Tubos MantenimientoCambiar LOS Filtros Deshidratadores DEL Refrigerante Manual DE Instrucciones Mantenimiento DE LOS Tubos DE Aire Acondicionado Vaciar EL Tanque DE Aceite UsadoMantenimiento DEL Caso Regulación DE LabalanzaelectrónicaBomba DE Vacío Reponer aceitePage Resolver Problemas Problemas DE RecuperaciónNo Entra Refrigerante Durante LA Recarga Garantía Limitada DEL Fabricante Para Utilizar LOS Servicios DE Esta GarantíaAnual DE Instrucciones Manual DE Instrucciones Wash hands after handling

VR-6000 specifications

The Viper VR-6000 is an innovative addition to the realm of virtual reality headset technology, designed to offer users an immersive and visually stunning experience. Built with meticulous attention to detail, the VR-6000 provides an ideal mix of high-end performance, comfort, and cutting-edge features that cater to both gamers and tech enthusiasts alike.

One of the standout characteristics of the Viper VR-6000 is its high-resolution display. The headset boasts a dual 4K OLED screen that delivers an exceptional pixel density, resulting in incredibly sharp visuals and vibrant colors that breathe life into the virtual environments. This feature significantly enhances the sense of realism, making every gaming session or virtual experience captivating.

The VR-6000 is powered by advanced refresh rate technology, providing a refresh rate of up to 120 Hz. This ensures smooth and fluid visuals, minimizing motion blur and enhancing responsiveness during fast-paced action scenes. Coupled with low-latency tracking, players can enjoy an almost instantaneous response as they move within their virtual space, making the experience feel more natural and engaging.

Comfort is another focal point of the Viper VR-6000 design. The headset has a lightweight frame and adjustable padding, which accommodates prolonged use without discomfort. It is designed to fit a wide range of head sizes, with a customizable strap system ensuring a secure and snug fit. Additionally, the integrated audio system features spatial sound technology that offers 3D audio experiences, allowing users to hear sounds from all directions, further enhancing immersion.

On the technological front, the Viper VR-6000 comes equipped with advanced motion tracking sensors. Utilizing a combination of inside-out tracking and external base stations, it allows for precise movement detection, which is crucial for room-scale VR experiences. Users can move freely within their designated space, and the system accurately reflects these movements in real time.

Compatibility is another highlight of the VR-6000. It supports a wide range of platforms, including both PC and console, allowing users to access an extensive library of VR titles. Moreover, the headset includes easy-to-use connectivity options, such as wireless capability and USB-C support, ensuring seamless integration with various devices.

In summary, the Viper VR-6000 represents a significant leap in virtual reality technology, offering an impressive array of features and capabilities. With its high-resolution display, advanced motion tracking, exceptional comfort, and compatibility with multiple platforms, it stands out as a top choice for those seeking an immersive VR experience. Whether for gaming, simulations, or interactive media, the VR-6000 promises to elevate the way users engage with the virtual world.
Top Page Image Contents