Wayne 200000-015 installation manual Installation Manual, Descriptions, Unpacking

Page 1

Sump, Effluent and Sewage pumps

INSTALLATION MANUAL

Read and save these instructions. This manual contains very important Safety Warnings and Operating Instructions. You will need to refer to it before attempting any installation or maintenance. Always keep this manual with the unit so that it will be easily accessible. Failure to read and follow these warnings and instructions could result in property damage, serious injury or death.

DESCRIPTIONS

SUMP PUMPS

Sump pumps are automatic pumps used to remove ground water from sump pits. The most common application is for basement drainage to prevent flooding in residential buildings. These sumps are designed to pump clear water only.

EFFLUENT PUMPS

Effluent pumps are pumps used to remove gray water from septic tanks, sump pits or laundry tray systems. Gray water is waste water from baths, sinks, washing machines, and other kitchen appliances. The pumps are designed to pass solids up to 3/4 in.

SEWAGE PUMPS

Sewage pumps are pumps used to remove waste water that contains solids up to 2 inches in diameter. The most common application is for draining bathroom waste water to a sewer or septic line.

UNPACKING

Inspect your pump. Occasionally, products are damaged during shipment. If the unit is damaged, return the unit to the place of purchase for replacement.

READ & FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS — DO NOT DISCARD

SAFETY GUIDELINES

This manual contains information that is very important to know and understand. This information is provided for SAFETY and to PREVENT EQUIPMENT PROBLEMS. To help recognize this information, observe all safety information labelled danger, warning, caution, and notice.

IMPORTANT SAFETY INFORMATION

WARNING INDICATES A POTENTIALLY HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, COULD RESULT IN DEATH OR SERIOUS INJURY.

RISK OF ELECTRIC SHOCK. TO REDUCE THIS

RISK, OBSERVE THE FOLLOWING WARNINGS:

MAKE SURE THERE IS A PROPERLY GROUNDED RECEPTACLE AVAILABLE. This pump is supplied with a grounding conductor and grounding-type attachment plug. To reduce the risk of electric shock, be certain that it is connected only to a properly grounded, grounding-type receptacle.

NEVER REMOVE THE GROUND PRONG from the plug or bypass the grounding wires.

FOR ADDED SAFETY the receptacle should be protected with a ground fault circuit interrupter (GFCI). All wiring must be performed by a qualified licensed electrician and comply with the National Electric Code and all applicable local codes and ordinances.

DO NOT REMOVE POWER SUPPLY CORD and strain relief or connect conduit directly to the pump.

MAKE SURE THE POWER SUPPLY HAS A FUSE OR CIRCUIT BREAKER rated to handle the current (amps) noted on the nameplate of the pump.

© 2010

DO NOT USE AN EXTENSION CORD. Extension cords could present a safety hazard if not sized properly, become damaged or the connection falls into the sump. If receptacle is not within reach of the pump’s power cord, contact a qualified licensed electrician to install a new receptacle.

ALWAYS DISCONNECT THE PUMP from power supply before installing, servicing or making any adjustments.

DO NOT SUBMERGE PEDESTAL MOTOR or allow motor to be exposed to water.

DO NOT WALK on the floor when water is present until all power is turned off. If the electric panel is in the basement, call an electrician.

NEVER HANDLE A PUMP or motor with wet hands or when standing on a wet or damp floor while the pump is plugged into the power supply.

WASH HANDS AFTER HANDLING. According to the state of California (Prop 65), this product may contain chemicals known to the state of California to cause cancer and birth defects or other reproductive harm.

RISK OF ELECTRIC SHOCK. This pump has not been investigated for use in swimming pool and marine areas.

DO NOT USE TO PUMP FLAMMABLE OR EXPLOSIVE FLUIDS such as gasoline, fuel oil, kerosene, etc. Do not use in a flammable and/or explosive atmosphere. Pump should only be used to pump clear water. Personal injury and/or property damage could result.

200000-015 6/10

Printed on 100% Recycled Paper

Image 1
Contents Safety Guidelines Installation ManualImportant Safety Information DescriptionsTypical Sump Installation Diagrams Installation ManualIT is Recommended to USE Rigid Piping This Pump should be Inspected 3 to 4 Times PERChart a Installation Manual Typical Sump InstallationEffluent Pump in Septic Tank Installation Manual Typical Effluent InstallationSubmersible Sewage Pumps Typical Sewage InstallationTroubleshooting MaintenanceSymptoms Possible Causes Always Disconnect the Pump from Power SupplySymptoms Possible Causes Suggested Remedies Installation Manual Déballage Manuel D’INSTALLATIONDirectives DE Sécurité Information Importante DE SécuritéDiagrammes D’INSTALLATION DE Pompes DE Puisard Typiques Manuel D’INSTALLATIONOn Recommande D’UTILISER UN Clapet DE NON-RETOUR Tableau a Manuel D’INSTALLATION Installation Typique DE PuisardTuyau de sortie de décharge Pompes d’égout submersibles Installation Typique DE Pompe Pour EAU UséeDépannage EntretienSymptômes Causes possibles Remèdes Suggérés Symptômes Causes possibles Dépannage SuiteManuel D’INSTALLATION Descripciones Manual DE InstalaciónDesempaque Guías DE SeguridadManual DE Instalación Diagramas Típicos DE Instalación DE SumiderosSE Recomienda EL USO DE Accesorios Y Tubería Tabla a Manual DE Instalación Instalación Típica DE SumideroInstale la tapa Figura 7 Bombas sumergibles para aguas cloacales Instalación Típica DE Bomba DE Aguas CloacalesMantenimiento Diagnóstico Y Resolución DE ProblemasSíntomas Causas posiblesSíntomas Causas posibles Remedios sugeridos Diagnóstico Y Resolución DE Problemas ContinúaManual DE Instalación Notas

200000-015 specifications

Wayne 200000-015 is a cutting-edge technological advancement in the world of automated systems, specifically designed for enhancing operational efficiency in various industrial sectors. This system stands out due to its advanced capabilities and features that streamline processes while ensuring maximum productivity.

One of the main features of Wayne 200000-015 is its robust processing power. Equipped with a state-of-the-art processor, it can handle complex algorithms and data analysis in real-time, making it ideal for sectors that require immediate decision-making. This speed ensures that users receive timely updates and insights, which can be crucial for maintaining a competitive edge.

A significant technological characteristic of the Wayne 200000-015 is its integration capability. The system is designed to seamlessly integrate with existing platforms, allowing for easy adoption without significant overhauls of current infrastructure. Its compatibility with various software applications ensures that users can utilize the technology in conjunction with their preferred tools, enhancing usability.

Another innovative aspect of the Wayne 200000-015 is its AI-driven analytics. Utilizing machine learning algorithms, the system continuously learns from operation data, providing predictive insights that help businesses forecast trends, optimize processes, and reduce downtime. This feature is particularly beneficial for maintenance scheduling, as it can anticipate potential failures before they occur, thus minimizing disruption to operations.

Security is a top priority with the Wayne 200000-015. It is equipped with advanced security protocols that ensure data integrity and protection against potential cyber threats. An encryption mechanism guards sensitive information while user access controls enable organizations to customize user permissions, ensuring that only authorized personnel have access to critical system functions and data.

Finally, the design of Wayne 200000-015 prioritizes user experience. Its intuitive interface allows users of varying technical skill levels to operate and navigate the system effortlessly. This consideration for user experience drives adoption rates as it reduces the learning curve associated with new technologies, ultimately leading to greater operational efficiency.

In conclusion, the Wayne 200000-015 is an exemplary embodiment of modern technology, combining powerful processing, seamless integration, AI-driven capabilities, robust security, and user-friendly design. Its features position it as an indispensable asset for businesses aiming to enhance their operational efficiency and stay ahead in a competitive landscape.