Wayne Official Manual for Conversion Burner P250AF and Safety Guidelines
Page 1

WAYNE COMBUSTION SYSTEMS

801 GLASGOW AVE.

FORT WAYNE, IN 46803

MODELS

P250AFP265

P250AF-EP P265F

P250AF-DI P265-EP P265-EP

GAS BURNER

Publication Date 5/01 - Revision B - Manual 101220

NOTE: Dimensions in ( ) are informational only. English values take priority.

FOR YOUR SAFETY

IF YOU SMELL GAS:

1.OPEN WINDOWS

2.DON’T TOUCH ELECTRICAL SWITCHES

3.EXTINGUISH ANY OPEN FLAME

4.IMMEDIATELY CALL YOUR GAS SUPPLIER.

CARBON MONOXIDE

POISONING HAZARD

CARBON MONOXIDE IS A COLORLESS, ODORLESS GAS THAT CAN KILL. FOLLOW THESE RULES TO CONTROL CARBON MONOXIDE.

▲Do not use this burner if in an unvented, enclosed area. Carbon monoxide may accumulate.

▲Do not adjust the pressure regulator. High pressures produce carbon monoxide.

▲Check flue gases for carbon monoxide. This check requires specialized equipment.

▲Allow only qualified burner service persons to adjust the burner. Special instruments and training are required.

▲Read the owner’s manual before using.

OVERHEATING HAZARD

SHOULD OVERHEATING OCCUR:

▲Shut off the manual gas valve to the appliance.

▲Do not shut off the control switch to the pump or blower.

WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.

-Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

-WHAT TO DO IF YOU SMELL GAS

•Do not try to light the appliance.

•Do not touch any electrical switch; do not use any phone in your building.

•Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

•If you cannot reach your gas supplier, call the fire department.

-Installation and service must be performed by a qualified installer, service agency or the gas supplier. Warranty is voided if not installed by qualified service person.

ELECTRIC SHOCK HAZARD

HIGH VOLTAGES ARE PRESENT IN THIS EQUIPMENT. FOLLOW THESE RULES TO AVOID ELECTRIC SHOCK.

▲Use only a properly grounded circuit. A ground fault interrupter is recommended.

▲Do not spray water directly on burner.

▲Turn off power before servicing.

▲Read the owner’s manual before using.

THESE INSTRUCTIONS SHOULD BE AFFIXED TO THE NOTICE BURNER OR ADJACENT TO THE HEATING APPLIANCE.

SPECIFICATIONS

BURNER MODELS

MINIMUM INPUT

MAXIMUM INPUT

FUELS

P-250AF & P-250AF-EP & P250AF-DI

50,000 BTU/HR (14.65 kW/Hr)

250,000 BTU/Hr (73.27 kW/Hr)

Natural & L.P. Gas

P-265 & P-265-EP

65,000 BTU/HR (19.05 kW/Hr)

200,000 BTU/Hr (58.61 kW/Hr)

Natural & L.P. Gas

P-265-F & P-265F-EP

65,000 BTU/HR (19.05 kW/Hr)

200,000 BTU/Hr (58.61 kW/Hr)

Natural & L.P. Gas

ELECTRICAL Power Supply - 115V/60HZ 1 Ph.

MOUNTING: Adjustable Flange is Standard

 

 

Pedestal Mount is Optional.

 

 

 

 

Page 1 Page 2
Image 1
Page 1 Page 2
Contents Wayne Combustion Systems Burner Models Minimum Input Maximum Input FuelsGlasgow AVE Fort WAYNE, Should Overheating OccurVisual Inspection of the Heating System Inspection of Heating Appliance Flue Pipe and Chimney12.7 mm Minimum rise 1/4 6.35 mm to the foot .305 m Flue Pipe and Draft Hood Preparation of Furnace or BoilerPreparation of Combustion Chamber Combustion Chambers Installation of Burner and ControlsSizing of Input in Relation to Furnace Natural GAS Propane GAS InputP265 only P250 onlyP265F only Limit Control Switches Electrical WiringTesting Piping for Leaks ThermostatEffective Overall Pipe Size Length Thread PurgingPipe Capacity Table Multiplier for Various Specific Gravities GravityStanding Pilot Combination GAS Valve Electronic Pilot Adjustment of BurnerP265DI P265DI Junction BOX RotatedFIG. a Best Locations for GASTrouble Chart Cause SymptomsGeneral Instruction Shutting Down the Burner ServiceOperation Start Stage Power InterruptionThermostat Controller Calls for Heat Spark Generator Pilot Burner OperationStart Direct Spark Ignition Honeywell S87K System P250AF Direct Spar Electrode LocationDirect Spark Ignition Honeywell System DescriptionPreliminary Checks TroubleshootingWHAT’S Wrong WHY What to do Service HINT, Diagnosis and Corrective MeasuresWiring Diagram Honeywell S87KDI System Ladder Form See chart Description P265FBB Parts List P265/P265F Series GAS BurnersP265FEP P265FDIP250AF EP P250AF DI Parts List P250AF Series GAS BurnersPage Wayne Combustion Systems

P265, P250AF, P265-EP, P250AF-DI, P250AF-EP specifications

Wayne P265-EP, P250AF-EP, P250AF-DI, P265F, and P265 are a series of fuel dispensing pumps known for their reliability and advanced technology. These pumps are engineered to meet the demanding needs of various fueling environments, making them suitable for both commercial and retail operations.

The Wayne P265-EP is particularly notable for its compact design and efficient performance. It features a user-friendly interface, making it easy for operators to manage fuel dispensing. Its electronic controller allows for precise monitoring and control of fuel flow, ensuring accurate transactions while minimizing wastage. The pump is also equipped with advanced security features to prevent unauthorized access.

The P250AF-EP and P250AF-DI models are designed with versatility in mind. They can support multiple fuel types, including gasoline, diesel, and biofuels, providing flexibility for businesses looking to serve a diverse clientele. The integrated diagnostics system helps operators identify issues quickly, reducing downtime and enhancing operational efficiency. Additionally, these models incorporate Wayne's SmartServe technology, which optimizes service intervals and maintenance schedules.

The P265F model emphasizes high performance and durability. Constructed with robust materials, it withstands harsh environmental conditions, making it ideal for outdoor installations. Featuring an advanced filtration system, it enhances fuel quality by removing contaminants, thereby extending the lifespan of both the pump and the connected storage tanks. Enhanced hydraulic efficiency translates to faster fueling times, increasing customer satisfaction at busy fueling stations.

Lastly, the P265 model stands out for its automatic nozzle shut-off function, which significantly reduces the risk of overfills and spills. This feature safeguards both the environment and the business against potential liabilities associated with fuel spillage.

In summary, the Wayne P265-EP, P250AF-EP, P250AF-DI, P265F, and P265 pumps incorporate cutting-edge technologies that prioritize efficiency, safety, and user convenience. Their advanced features ensure reliable performance across a variety of fueling applications, making them a preferred choice for operators seeking high-quality dispensing solutions. Whether it's speed, security, or flexibility, Wayne pumps are engineered to meet the evolving needs of the fuel distribution industry.
Top Page Image Contents