Installation Locations | Kidde KN-COPF-I instruction

Recommended Locations

2. Product Features and Specifications

Temperature:

Operating Range: 40°F (4.4°C) to 100°F (37.8°C)

Humidity:

Operating range: 10-95% non-condensing

Audible Alarm:

85+ dB at 10’ @ 3.4±0.5 KHz pulsing alarm

Sensor:

Electrochemical

Power:

120 volts AC, 60 Hz, 30 mA max, rechargeable battery back-up

Accuracy of Digital Display (Model KN-COP-IC only):

30-999 PPM +/-30% when measured in conditions of 80° F (+/- 10° F), atmospheric pressure +/- 10% and 40% +/- 3% relative humidity. Display readings may vary slightly depending on changes in the ambient condition (temperature, humidity) and the condition of the sensor.

Alarm Response Times:

70 PPM = 60-240 min., 150 PPM = 10-50 min., 400 PPM = 4-15 min.

Interconnection with Other Alarms:

This Kidde CO alarm can be used as a single-station alarm or intercon- nected with other Kidde alarms. This alarm can be interconnected direct- ly with these Kidde models:

Ionization smoke alarm models:

1235, 1235CA, 1275, 1275CA, 1276,1276CA, 1285, 1285CA, i12020, i12040, i12060, i12080, i12020CA, i12040CA, i12060CA, RF-SM-ACDC, KN-SMFM-i

Photoelectric smoke alarm models:

PE120, PE120CA, PI2000, PI2000CA

Heat alarm models:

HD135F, HD135FCA

Carbon monoxide/Ionization smoke alarm models:

KN-COSM-IB, KN-COSM-IBCA

Carbon monoxide alarm models:

KN-COB-IC, KN-COP-IC, KN-COB-ICB, KN-COP-ICB

Relay models:

CO120X, SM120X

Strobe Light models:

SL177I

3. Installation Locations

Recommended Installation Locations

CO alarms should be mounted in or near bedrooms and living areas. It is recommended that you install a Kidde CO alarm on each level of your home.

When choosing your installation loca- tions, make sure you can hear the

alarm from all sleeping areas. If you install only one CO alarm in your

home, install it near bedrooms, not in the basement or furnace room.

•When wall mounting, place out of reach of children. Under no cir- cumstances should children be allowed to handle the CO alarm.

•Placing the alarm at eye level allows for optimum monitoring of the digital display.

Locations To Avoid

IMPORTANT: Improper location can affect the sensitive electronic com- ponents in this alarm. To avoid causing damage to the unit, to provide optimum performance, and to prevent unnecessary nuisance alarms:

•Do not install in kitchens, garages or furnace rooms that may expose the sensor to substances that could damage or contaminate it.

•Do not install in areas where the temperature is colder than 40°F (4.4°C) or hotter than 100°F (37.8°C) such as crawl spaces, attics, porches and garages.

•Do not install within 5 ft. of heating or cooking appliances. (Kidde recommends 15 ft. to prevent nuisance alarms).

•Do not install near vents, flues, chimneys or any forced/unforced air ventilation openings.

•Do not install near ceiling fans, doors, windows or areas directly exposed to the weather.

•Do not install in dead air spaces, such as peaks of vaulted ceilings or gabled roofs, where CO may not reach the sensor in time to provide early warning.

•Do not install on a switched or dimmer-controlled outlet.

•Do not install this unit near deep-cell large batteries. Large batteries have emissions that can cause the alarm to perform at less than opti- mum performance.

KN-COPF-I specifications

The Kidde KN-COPF-I is a state-of-the-art carbon monoxide and propane gas detector designed to ensure the safety of homes and commercial spaces. With an emphasis on user-friendly features and advanced technology, this model stands out as a reliable solution for detecting harmful gases that can pose health risks to occupants.

One of the primary features of the Kidde KN-COPF-I is its ability to detect both carbon monoxide and propane gas. Carbon monoxide is a colorless, odorless gas that can be lethal if levels build up within an enclosed space. The KN-COPF-I is equipped with a highly sensitive electrochemical sensor specifically designed to identify even low levels of carbon monoxide. Additionally, the unit detects propane gas leaks, making it suitable for homes that use propane for heating or cooking, further enhancing its versatility in the realm of safety devices.

The KN-COPF-I features a digital display that provides continuous monitoring of both CO and propane levels in real-time. This digital interface allows users to easily keep track of their environmental safety, as it displays the current levels and alerts when they reach dangerous thresholds. The device also includes a peak level memory function, which records the highest concentration of carbon monoxide detected, allowing users to review previous incidents.

Installation and usability are key considerations in the design of the Kidde KN-COPF-I. The unit comes with a mounting bracket, making it simple to install on walls or ceilings in strategic locations throughout the home. It is powered by an AC power source, ensuring continuous operation, while a battery backup provides additional security in the event of a power outage.

Another significant characteristic of the Kidde KN-COPF-I is its safety alarms, which include a loud 85-decibel warning signal for carbon monoxide detection, as well as visual alerts for propane detection. These alarms are crucial for alerting occupants promptly, allowing them to take necessary actions to evacuate or respond to hazards before they escalate.

For added peace of mind, the Kidde KN-COPF-I also features a test/reset button, which allows users to routinely check the functionality of the device and ensure that it operates correctly. This ensures that the detector remains reliable over time.

In conclusion, the Kidde KN-COPF-I combines advanced detection technologies with intuitive features to provide comprehensive protection against carbon monoxide and propane gas. Its digital display, dual detection capability, and easy installation make it an essential device for any safety-conscious household.