SS103 Operation, Testing the System | Macurco SS103-3A, SS102H

MACURCO CONTROLLERS & DETECTORS (CONT.)

SS103 OPERATION

START-UP

Turn the FAN sensitivity level pots to the center of their ranges. When power is first applied to the SS103, only the Green “POWER” light should be on. If SS102HC-1sensors are used, the appropriate green SENSOR lights on the SS103 will be on, and

One or more FAN circuits may turn on as the SS102HC-1goes through its self test cycle, which provides an increasing voltage during the warm up cycle. After one and one half minutes, the SS102H sensors will complete their warm-ups, and all SS102 “SENSOR” green lights should be on. (If not all zones are used on the SS103-3A&-10Aonly those appropriate green lights will be on). These SS103 green lights show the sensors are on and in normal operation, and that the wiring between the sensor and control panel is OK. The SS102HC-1has a 2 1/2 minute warm-up cycle, during which the output voltage progressively increases from 1.0 to 2.1 volts, which will cause the appropriate SS103 zone lights to actuate.

Some or all of the Red “SENSOR” lights on the SS103-10Apanel may be on at this time. These red lights show when a sensor output reaches the level of carbon monoxide to actuate FAN1, FAN2 or FAN3/ALARM. At the same time a SENSOR Red light turns on, the amber FAN light or lights start to flash on and off. If the level of CO is high enough, the Red ALARM light also will flash on and off. Flashing lights indicate that the time delays before relay turn on has been activated.

The SS103-3Ahas multi-colored lights to show sensor status. They will be off on zones to which no sensors are connected. Normal operation and clean air is shown by a green sensor light. The light turns amber when “FAN 1” is actuated, then turns red when “FAN 2” is exceeded. The ALARM relay is delayed, by the ALARM DELAY setting, from the FAN 2 level setting.

Allow the system to stabilize for 10 or 20 minutes. All SENSOR red lights, the FAN amber lights, and the red ALARM lights should be off once the sensors have warmed up, and the air has been cleared out by the fans.

SS103-10A

For the SS103-10A, from the time a “SENSOR” red light turns on, at which time the amber FAN light starts to flash on and off, there is a two minute delay before the fan relay is actuated, as shown by a continuous FAN light. Any of the SENSOR red lights turn on whenever the Fan sensitivity setting is exceeded at any sensors location. Should the Carbon Monoxide level continue to rise, FAN 2 on the SS103-10Awill turn on, then the FAN3/ALARM will turn on. At first, the red FAN3/ALARM light flashes on and off during the delay period, then turns on steady as the relay closes to actuate the alarm circuit.

SS103-3A

The SS103-3Adiffers in operation in that it has a shorter delay (30 seconds) FAN on and a short (15 second) FAN turn off delay. Also, the ALARM range is adjustable continuously from 3 to 33 minutes. This ALARM relay is delayed from the FAN 2 turn on set point.

The unit uses 10Amp field replaceable Autofuses on the three output relay circuits to protect them.

TESTING THE SYSTEM

The best way to functionally test the systems is to run a car (the older and smog producing the better) near each sensor and observe system operation. Make sure the SS103 potentiometers are set in reasonable ranges: The Fans between 50 and 150 and the Alarm at 200 or less.

SS102H

Functionally test the system by introducing Carbon Monoxide gas into each sensor, while watching for each SS103 SENSOR red light to turn on. A convenient source of CO is cigarette smoke. Hold a lighted cigarette under each sensor, for several minutes, so the smoke drifts up through the sensor. Gas from an unlit butane cigarette lighter can also be used to test the system. Shoot the gas into the holes near the lights of the case. If the job specifications require actual CO testing, the SS102HC-1sensors should be used.

SS102HC-1

A switch inside the sensor is labeled TEST. Pushing this switch once puts the sensor into a 2 1/2 minute test mode where it steps from 1.0 to 2.1 volts. This progressive increase in voltage will cause the SS103 control panel to turn on Fan and Alarm relays accordingly. The SS102HC-1optional Field Calibration Kit (FCK), which includes a cylinder of 50 ppm carbon monoxide gas, can be used to test the SS102HC-1sensors. If the job requires actual CO testing, other cylinders of gas at other levels can be purchased, and used with the FCK.

SS102HC-1, SS103-10A, SS103-3A, SS102H specifications

Macurco provides advanced gas detection solutions with the SS102H, SS103-10A, SS102HC-1, and SS103-3A models, designed to ensure safety in various environments. These models are known for their reliability, accuracy, and ease of integration into existing systems.

The Macurco SS102H is a standalone carbon monoxide detector, renowned for its high sensitivity and quick response time. It features a self-diagnostic function that continuously tests the sensor and output circuits to ensure they are operating correctly. The unit is equipped with a 4-20 mA output for easy connectivity with building management systems. It also comes with a durable housing that makes it suitable for both residential and commercial applications.

The SS103-10A model is a versatile gas detector capable of sensing both carbon dioxide and carbon monoxide. This dual-functionality is crucial in environments like restaurants and industrial kitchens where multiple gas detection is vital. This model features a robust sensor technology that ensures precise measurements and a long operational life. It also includes an adjustable relay output, allowing users to set alarm conditions according to specific needs.

For environments requiring continuous monitoring and alert systems, the Macurco SS102HC-1 is designed to detect harmful gases like carbon monoxide, methane, and propane. Its advanced analytical technology can distinguish between these gases effectively, making it ideal for residential, commercial, and industrial applications. The SS102HC-1 is also designed for easy calibration and features a visual and audible alarm, ensuring quick response in emergencies.

Lastly, the SS103-3A model offers enhanced detection capabilities for various combustible gases. With its wide array of sensor technologies, this model excels in providing accurate readings, even in challenging conditions where other detectors might fail. It is ideal for both indoor and outdoor applications. Additionally, the SS103-3A supports multiple output options including relay, analog voltage, and serial communication, making it easy to integrate into existing alarm systems.

In summary, the Macurco SS series provides reliable, accurate, and robust gas detection solutions tailored to meet the demands of various environments. Their innovative technologies ensure durability, longevity, and safety, making them indispensable in maintaining air quality and preventing hazardous situations.