CDA HCG301 manual 6INSTALLATION, GAS Cooking Hobs, Technical Information for the Installer

Page 12

Installation advice

6INSTALLATION

IMPORTANT

The appliance should be installed, regulated and adapted to function with other types of gas by a QUALIFIED INSTAL-

LATION TECHNICIAN.

Failure to comply with this condition will render the guaran- tee invalid.

The appliance must be installed in compliance with regula- tions in force.

Installation technicians must comply to current laws in force concerning ventilation and the evacuation of exhaust gases.

Always unplug the appliance before carrying out any main- tenance operations or repairs.

The appliance must be housed in heat-resistant units.

These tops are designed to be embedded into kitchen fixtures measuring 600 mm in depth.

The walls of the units must not be higher than work top and must be capable of resisting temperatures of 75 °C above room temperature.

Do not instal the appliance near inflammable materials (eg. curtains).

GAS COOKING HOBS

288

510

288

510

 

 

30

30

 

 

 

50

 

 

 

50

 

 

 

 

490

+0

 

 

490

+

0

 

0

 

 

 

 

 

 

0

 

2

 

+ 2

 

2

270

+ 2

 

 

 

270

 

 

 

 

 

 

Fig. 6.1a

 

 

 

Fig. 6.1b

 

 

 

 

TECHNICAL INFORMATION FOR THE INSTALLER

Before installing the cooktop, remove the protective film.

This cooktop can be built into a working surface 20 to 40 mm thick and 600 mm deep.

In order to install the cooker top into the kitchen fixture, a hole with the dimensions

 

 

 

 

 

shown in figs. 6.1a - 6.1b has to be made, keeping in consideration the following:

 

 

 

 

 

– within the fixture, between the bottom side of the cooker top and the upper sur-

450 mm

 

650 mm

 

 

 

 

 

face of any other appliance or internal shelf there must be a clearance of at least

 

 

 

30 mm;

 

 

 

– the cooker top must be kept no less than 100 mm away from any side wall;

 

 

 

 

 

 

 

 

 

 

– the cooker top must be kept at a distance of no less than 50 mm from the rear

 

 

 

 

 

wall.

 

 

 

 

 

– there must be a distance of at least 650 mm between the hob and any wall cup-

 

 

 

 

 

board or extractor hood positioned immediately above (see fig. 6.2)

 

 

 

 

 

– the coatings of the walls of the unit or appliances near the cooktop must be heat

 

 

 

 

 

resistant ("Y" protection against heating in compliance with standards EN

 

 

 

 

 

60335-2-6).

 

 

 

 

 

Do not instal the appliance near inflammable materials (eg. curtains).

Fig. 6.2

 

 

 

 

 

 

 

 

31

 

 

 

Image 12
Contents HCG301 Domino Two Burner Gas Hobs Important Precautions and Recommendations EnglishTips for the User Declaration of CE Conformity1FEATURES GAS Cooking HOB FigGAS triple ring burner Cooking HOB Fig Electric Cooking HOB Fig Lighting GAS Burners Fitted with Safety Valve Device GAS Cooking HobsGAS Burners Valveless Electric SPARK-LIGHTING GAS BurnersChoice of Burner fig Grate for Small Pans optional See figSpecial WOK Grille optional .6 e Electric Cooking Hobs Normal HotplateRapid Hotplate red dot Proper USE of the Electric Hotplate figVitroceramic Hobs Types of Cooking AreaCircuiti radiant zones Fig Hi-light radiant zones FigType of cooking Hints for Safe USE of the HobsCleaning and Maintenance Correct Replacement of the Burners Burners and GridsTriple Ring Burner 6INSTALLATION Technical Information for the InstallerGAS Cooking Hobs With Cupboard Doors fig Fastening the Cooktop figChoosing Suitable Surroundings for gas models Discharging Products of CombustionElectrical Plates and Vitroceramic Cooking Hobs Fastening the Cooktop GAS Section GAS ConnectionsGases Operations to be Performed When Substituting the Injectors Regulating the Burner Minimum SettingLubricating the GAS Taps Electrical Section DetailsRepairs Feeder Cable SectionParte Eléctrica Ligação À Rede EléctricaReparações Secção DOS Cabos DE AlimentaçãoCod