Beckett CG10 manual Pre-installation Checklist, Indoor Installation Protect against Dust Moisture

Page 5

Section: Pre-installation Checklist

Figure 1. Burner Nameplate

General Model Information

Serial Number,

R.W. Beckett

Construction and Setting Data

Including Date Code

 

Rating Information

R.W. Beckett Specification

Number and Revision

 

Approval Agency

 

Symbols

Boiler Manufacturer and Model,

 

 

When Applicable

Primary Group

Additional Codes

and Fuel

 

Pre-installation Checklist

Combustion air supply

Adequate Combustion and

Ventilation Air Supply

Required

Failure to provide adequate air supply could seriously affect the burner performance and result in damage to the equipment and emission of poisonous carbon monoxide gas.

yThe burner cannot properly burn the fuel if it is not supplied with a reliable combustion air source.

yFollow the guidelines in the latest edition of National Fuel Gas Code ANSI Z223.1 (NFPA 54) and CAN1-B149.1 regarding providing adequate air for combustion and ventilation.

yFor appliance/burner units in confined spaces, the room must have an air opening near the top of the room, plus one near the floor, each with a free area at least one square inch per 1000 Btu/hr input for all fuel-burning equipment in the room.

Indoor Installation

Protect against Dust and

Moisture

Wet or dusty environments could lead to blocked air passages, corrosion damage to components, impaired combustion performance and result in asphyxiation, explosion or fire.

yThis burner is designed for clean, dry installations.

yElectrical controls are not protected against rain or sprayed liquids.

yKeep the installation clear of dust, dirt, corrosive vapors, and moisture.

yProtective covers and more frequent maintenance may be required.

If there is risk of the space being under negative pressure, or of exhaust fans or other devices depleting available air for combustion and ventilation, the appliance/burner should be installed in an isolated room provided with outside combustion air.

CG10 Burner Manual

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Fire, Explosion and Asphyxiation Hazards Contents Hazard Definitions General InformationOwner’s Responsibility Follow these instructions exactly To the OwnerAgency Approvals Special Requirements When contacting Beckett forExactly Indoor Installation Protect against Dust Moisture Pre-installation ChecklistClearances Test For Gas Pipe LeaksVerify firing input range Fuel gas supplyMBH Verify burner air tube assemblyBurner Model Airtube Dim. a Dim. B Burner DimensionsConnect Gas Piping Mount the BurnerProtect the Air Tube from Overheating Do Not Use Teflon Tape on Gas PipingGas Trains Gas Leaks and Exposion Hazards Install a Drip Leg in Gas Supply PipingGas supply piping capacity Pipe Length ftUL gas train configuration Keep Service Access Covers Securely Installed Wire the BurnerDo Not Bypass Safety Controls Electrical Shock HazardDelayed Ignition, Explosion Fire Hazards Professional Installation Service RequiredSequence of Operation Prepare the Burner for Start-upGas Supply Piping GeneralElectrical Boiler or ApplianceMajor Components Item Description CG10 component familiarizationVerify input firing rate Burner start procedureStart the Burner Shutter and Band Initial burner settingsEstimating Rate Temperature correctionClocking a gas meter Uncorrected flow rateCG10.6S CG10.5S CG10.4S CG10.3S CG10.2S CG10.1S Flame safeguard safety lockout Simulate a Recommended combustion test sequence Use test instruments to set combustionAnnual Professional Service Required Maintenance and ServiceAnnual maintenance Turn Off Electric and Gas Supply Before ServicingFlame safeguard Adjust the burner for proper combustionInstallation area Ignition Reliability Manual shutdown for long periodsGas Gun Assembly Propane Restrictor Description InstallationPropane Restrictors Replacement Part NumbersTest/Inspection Frequency Comments Inspect Heating System RegularlyPeriodic Inspection Sheet See Table Replacement PartsHigh Rate Burner Configuration 600 to 1200 MBH Applications Burner ConfigurationsLow Rate Burner Configuration 300 to 800 MBH Applications Air Platform Blower Wheel Air Inlet Gas Gun Nominal Assembly Capacity, MBHBurner Model ShroudCG10 Burner Manual Limited Warranty Information
Related manuals
Manual 2 pages 33.71 Kb

CG10 specifications

The Beckett CG10 is a premium gas furnace that stands out in today's competitive heating market due to its innovative technology and reliable performance. Designed with efficiency and comfort in mind, the CG10 model ensures optimal heating solutions for residential spaces.

One of the most significant features of the Beckett CG10 is its impressive Annual Fuel Utilization Efficiency (AFUE) rating. With ratings often exceeding 90%, this furnace significantly reduces energy consumption and ensures cost-effective heating. This high-efficiency rating translates to lower utility bills and less environmental impact, making it a smart choice for eco-conscious homeowners.

The CG10 utilizes advanced combustion technology to ensure that fuel is burned effectively, maximizing heat generation while minimizing emissions. This innovative technology not only enhances the furnace's performance but also contributes to cleaner air, aligning with modern environmental standards.

A notable characteristic of the Beckett CG10 is its quiet operation. The unit is designed to operate with minimal noise, ensuring a comfortable living environment without disruptive sounds. This is particularly important for families and individuals who prioritize tranquility in their homes.

The furnace is built with durable materials, ensuring longevity and reliable performance over the years. Its construction adheres to strict industry standards, making the CG10 both robust and dependable. Regular maintenance is simplified thanks to its user-friendly design, which allows homeowners to access critical components easily.

Safety is a paramount concern in any heating system, and the Beckett CG10 does not disappoint. It comes equipped with multiple safety features, including flame sensors and safety shut-off mechanisms, ensuring peace of mind for users.

Additionally, the Beckett CG10 can be integrated with smart home technology, allowing homeowners to monitor and control their heating system remotely. This capability enhances convenience and provides further energy savings, as users can adjust their heating preferences from anywhere.

In summary, the Beckett CG10 gas furnace presents an ideal solution for homeowners seeking a blend of efficiency, durability, and advanced technology in their heating systems. Its high AFUE rating, quiet operation, and safety features make it a top choice for those prioritizing comfort and environmental responsibility.
Top Page Image Contents