Beckett 120 Vac/60 Hz instruction manual Verify specifications Be aware of hazard definitions

Page 3

Instruction Manual – Model AFG Oil Burner

Prepare before installing

Verify specifications

Be aware of hazard definitions

Denotes presence of a hazard which, if ignored, will result in se- vere personal injury, death or substantial property damage.

Denotes presence of a hazard which, if ignored, could result in severe personal injury, death or substantial property damage.

Denotes presence of a hazard which, if ignored, could result in minor personal injury or property damage.

Intended to bring special attention to information, but not related to personal injury or property damage.

Check certifications/approvals

• Underwriters Laboratories￿has certified this burner to comply with ANSI/UL 296 and has listed it for use with #1 or #2 fuel oil as specified in ASTM D396. Low sulfur #1 and #2 fuel oils reduce heat exchanger deposits with all burners compared to the standard fuels. Reduced deposits ex- tend the service interval for cleaning and improve the efficiency of the appliance over time. Low sulfur fuels reduce particulate and oxides of nitrogen emissions as well. The Oilheat Manufacturers' Association rec- ommends these fuels as the preferred fuels for this burner.

• State and local approvals are shown on burner rating label (see below).

• All oil burners should be installed in accordance with regulations of the latest revision of the National Fire Protection Association￿Standard NFPA 31 and in complete accordance with all local codes and authorities having juris- diction. Regulation of these authorities take precedence over the general instructions provided in this installation manual.

• For recommended installation practice in Canada, reference to CSA Standard B139-M91.

Notice special requirements

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿This equipment must be installed, adjusted and started only by a

– an individual or agency, licensed and experienced with all codes and ordinances, who is responsible for the installation and adjust- ment of the equipment. The installation must comply with all local codes and ordinances and with the latest revision of the National Fire Protection Standard for Oil-Burning￿￿￿￿￿Equipment,￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿NFPA 31 ￿￿￿￿￿￿￿(or CSA￿￿￿￿￿￿￿￿￿￿B139-M91).

. Follow all instructions completely. Failure to follow these instructions could result in equipment mal- function, causing severe personal injury, death or substantial property damage.

Concealed damage — If you discover damage to the burner or controls during unpacking, notify the carrier at once and file the appropriate claim.

When contacting Beckett for service information — Please record the burner serial number (and have available when calling or writing). You will find the serial number on the Underwriters Laboratories label, located on the left rear of the burner, or the cover mounting plate. See illustration below.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Motor voltage 120 Vac / 60 Hz AFG OilMount burner on appliance Inspect/prepare installation sitePerform annual maintenance To replace the blower wheel Owner’s information and warrantyVerify specifications Be aware of hazard definitions Outside air kit applications Chimney or vent Clearances to burner and applianceDirect air supply and sidewall venting Combustion air supplyPrepare burner Check/adjust Z dimension F head Dimensions for Figures 2, 3Beckett T500 gauge may also be used Starting adjusting plate settings with V1 head L1 heads see and for dimensionsMount burner on appliance Connect fuel lines Wire burnerR7184 primary control features Power before servicingLet burner run for approximately 5 to 10 minutes Perform annual maintenanceStartup burner/set combustion To replace blower wheelAwaiting New info Replacement partsDaily Owner’s information Owner service and maintenanceWarranty Annually minimum

120 Vac/60 Hz specifications

The Beckett 120 Vac/60 Hz is a versatile and reliable solution designed for a variety of heating applications. This model exemplifies a combination of efficiency, user-friendliness, and advanced technology, making it a popular choice for both residential and commercial heating needs.

One of the standout features of the Beckett 120 Vac/60 Hz unit is its exceptional energy efficiency. Designed to minimize energy consumption while maximizing heat output, it incorporates modern technology that helps reduce operating costs. The unit is built with a continuously adjustable firing rate, allowing it to operate at the optimal heating level for varying demand. This not only improves efficiency but also ensures consistent temperature control throughout the space.

Another significant characteristic of the Beckett model is its robust construction. Made from high-quality materials, the unit is designed to withstand the rigors of daily use while maintaining reliable performance. The design also includes features that reduce wear and tear, increasing its longevity and reliability.

Safety is paramount with the Beckett 120 Vac/60 Hz. It comes equipped with multiple safety features, including automatic shut-off mechanisms and overheating protection. This ensures both user safety and peace of mind, making it ideal for families and businesses alike.

The advanced technology used in this model includes a sophisticated control system that allows for precise monitoring and adjustments. Users benefit from intuitive interfaces that provide real-time information about system performance, enabling easy troubleshooting and maintenance.

The Beckett unit also boasts quiet operation, making it suitable for environments where noise reduction is essential. Its compact design allows for flexibility in installation, whether it be in a tight utility room or a more spacious area.

Furthermore, the Beckett 120 Vac/60 Hz supports a range of fuel types, enhancing its versatility. Whether you are using oil, gas, or other alternatives, this unit is equipped to operate efficiently with minimal adjustments.

In summary, the Beckett 120 Vac/60 Hz combines exceptional efficiency, safety features, and advanced technology into a compact and robust heating solution. Its versatility and user-friendly design make it an excellent choice for a variety of applications, offering peace of mind and comfort to both homeowners and businesses.
Top Page Image Contents