Desa RG30NT, GG30NT, FG30PT, FG30NT, RG30P Determining FRESH-AIR Flow for Heater Location

Page 6

AIR FOR COMBUSTION

AND VENTILATION

Continued

DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION

Determining if You Have a Confined or Unconfined Space

Use this work sheet to determine if you have a con- fined or unconfined space.

Space: Includes the room in which you will install heater plus any adjoining rooms with doorless pas- sageways or ventilation grills between the rooms.

1.Determine the volume of the space (length x width x height).

Length x Width x Height =__________cu. ft. (volume of space)

Example: Space size 20 ft. (length) x 16 ft. (width) x 8 ft. (ceiling height) = 2560 cu. ft. (volume of space)

If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of the space.

2.Multiply the space volume by 20 to determine the maximum Btu/Hr the space can support.

_______ (volume of space) x 20 = (Maximum Btu/Hr the space can support)

Example: 2560 cu. ft. (volume of space) x 20 = 51,200 (maximum Btu/Hr the space can support)

3.Add the Btu/Hr of all fuel burning appliances in the space.

Vent-free heater

______________ Btu/Hr

Gas water heater*

______________ Btu/Hr

Gas furnace

______________ Btu/Hr

Vented gas heater

______________ Btu/Hr

Gas fireplace logs

______________ Btu/Hr

Other gas appliances* + __________

Btu/Hr

Total

= __________

Btu/Hr

*Do not include direct-vent gas appliances. Di- rect-vent draws combustion air from the outdoors and vents to the outdoors.

Example:

 

 

 

Gas water heater

 

40,000

Btu/Hr

Vent-free heater

+

30,000

Btu/Hr

Total

=

70,000

Btu/Hr

4.Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.

_______________Btu/Hr (maximum the space can support)

_______________Btu/Hr (actual amount of Btu/Hr used)

Example:

51,200 Btu/Hr (maximum the space can support)

70,000 Btu/Hr (actual amount of Btu/Hr used)

The space in the above example is a confined space because the actual Btu/Hr used is more than the maxi- mum Btu/Hr the space can support. You must provide additional fresh air. Your options are as follows:

A.Rework worksheet, adding the space of an adjoin- ing room. If the extra space provides an unconfined space, remove door to adjoining room or add ventilation grills between rooms. See Ventilation Air From Inside Building, page 7.

B.Vent room directly to the outdoors. See Ventila- tion Air From Outdoors, page 7.

C.Install a lower Btu/Hr heater, if lower Btu/Hr size makes room unconfined.

If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an uncon- fined space. You will need no additional fresh air ventilation.

WARNING: If the area in which the heater may be oper- ated is smaller than that defined as an unconfined space or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one of the methods described in the National Fuel Gas Code, ANSI Z223.1/NFPA54 Section 5.3 or applicable local codes.

6

www.desatech.com

114683-01B

Image 6
Contents What to do if YOU Smell GAS Table of Contents Safety Information Poisoning may lead to deathProduct Features Local CodesUnpacking Following are excerpts from National Fuel AIR for Combustion VentilationProviding Adequate Ventilation Unusually Tight ConstructionDetermining FRESH-AIR Flow for Heater Location Determining if You Have a Confined or Unconfined SpaceCheck GAS Type InstallationVentilation AIR Ventilation Air From Inside BuildingInstallation Items Locating HeaterMounting Bracket Installing Heater to WallThermostat Sensing Bulb Thermostat Models Only Removing Front Panel Of HeaterAttaching To Wall Anchor Method Placing Heater On Mounting BracketInstalling Bottom Mounting Screws Installing Bottom Mounting ScrewsConnecting to GAS Supply Typical Inlet Pipe DiameterPsig 3.5 kPa Checking GAS ConnectionsTest Pressures Equal To or Less Than EquipmentOpen equipment shutoff valve see , Make sure control knob of heater is in the OFF positionManual Control Models For Your Safety Read Before Lighting Operating HeaterLighting Instructions Shutting Off Heater Manual Lighting ProcedureTo Turn OFF GAS To Appliance Shutting Off Burner Only pilot stays litThermostat Control Operation Burner Flame Pattern Inspecting HeaterPilot Flame Pattern Check pilot flame pattern and burner flame pat- tern oftenBurner Pilot AIR Inlet Cleaning MaintenanceODS/PILOT and Burner CabinetTroubleshooting Observed Problem Possible Cause RemedyDelayed ignition of burner Manifold pressure is too low Out when control knob is re Control knob not pressedSafety interlock system has Burner orifice is clogged Clean burner see CleaningTurning control knob to Or shut off Qualified service personOperation Processes Hours of operation Air passageways on heaterGas leak. See Warning Statement aboveSpecifications BG30N, FG30N, GG30N, RG30N, GMG30NBG30P, FG30P, GG30P, RG30P, GMG30P Service Publications Replacement Parts Service HintsTechnical Service Parts Under WarrantyIllustrated Parts Breakdown Parts List NJF 8CIllustrated Parts Breakdown NJF 8C FAN Kits GA3250T AccessoriesEquipment Shutoff Valve GA5010 For all models. Equipment shutoff valve with 1/8 NPT tapParts Centrals Warranty Information Keep this WarrantyLimited Warranty VENT-FREE Residential GAS Heaters