Desa CRN30 Mounting Heater to Floor, Connecting to GAS Supply, Mounting Base Feet to Heater

Page 11

INSTALLATION

Continued

MOUNTING HEATER TO FLOOR

Mounting Base Feet to Heater

1.Lay heater cabinet on its back on a table with the heater bottom overhanging the table edge.

2.Align holes in base foot with mounting holes on bottom of cabinet (see Figure 13).

3.Secure base foot to heater using sheet metal screws.

4.Repeat for other side.

Mounting Base Feet to Floor (Where required by local code)

1.Remove front cover (see Removing Front Panel of Heater, page 8).

2.Position heater with base feet in desired loca- tion. Mark holes for drilling. Remove heater with base.

3.For carpeted floors, make a small cut with a sharp knife at marked locations prior to drill- ing. If mounting base to a wood floor, drill 1/8 inch diameter hole, 3/4 inch deep. (Do not use anchors in wood floors).

If mounting base to a concrete floor, drill with 1/4 inch diameter concrete drill bit, 13/8 inches into floor. Insert anchors completely into holes.

4.Reposition heater with base feet over holes. Secure base to floor with wood screws. See Figure 13.

Wood

Screw

Base Foot

Sheet Metal Screw

Figure 13 - Installing Base Feet

CONNECTING TO GAS SUPPLY

WARNING: This appliance requires a 3/8" NPT (National Pipe Thread) inlet connection to the pressure regulator.

WARNING:Aqualifiedservice personmustconnectheatertogas supply. Follow all local codes.

WARNING:Fornaturalgas,never connectheatertoprivate(non-utility) gas wells. This gas is commonly known as wellhead gas.

IMPORTANT: For natural gas, check gas line pressure before connecting heater to gas line. Gas line pressure must be no greater than 10.5 inches of water. If gas line pressure is higher, heater regula- tor damage could occur.

CAUTION: For propane/LP gas, never connect heater di- rectly to the propane/LP supply. This heater requires an external regulator (not supplied). Install theexternalregulatorbetweenthe heater and propane/LP supply.

For propane/LP gas, the installer must supply an external regulator. The external regulator will reduce incoming gas pressure. You must reduce incoming gas pressure to between 11 and 14 inches of water. If you do not reduce incoming gas pres- sure, heater regulator damage could occur. Install the external regulator with the vent pointing down as shown in Figure 14. Pointing the vent down protects it from freezing rain or sleet.

Propane/LP

External

Supply Tank

 

Regulator

Vent

Pointing

Down

Figure 14 - External Regulator With Vent

Pointing Down

107883-01H

www.desatech.com

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Model CRN30 Shown CRP26, CRP26T, CRT26PT, CRN30, CRN30T, CRT30NTTable of Contents Safety Information Unpacking Product FeaturesLocal Codes Determining FRESH-AIR Flow for Heater Location AIR for Combustion VentilationProviding Adequate Ventilation Ventilation Air From Inside Building Ventilation AIRLocating Heater InstallationInstallation Items Check GAS TypeMounting Bracket Installing Heater to WallThermostat Sensing Bulb Thermostat Models OnlyAttaching To Wall Anchor Method Methods For Attaching Mounting Bracket To WallMarking Screw Locations Plaque HeaterPlacing Heater On Mounting Bracket Installing Bottom Mounting ScrewsMounting Base Feet to Heater Connecting to GAS SupplyMounting Base Feet to Floor Where required by local code Mounting Heater to FloorJoint Nipple Sediment Trap From External Regulator Checking GAS ConnectionsTest Pressures Equal To or Less Than 1/2 Psig 3.5 kPa Test Pressures In Excess Of 1/2 Psig 3.5 kPaLighting Instructions NON-THERMOSTAT Models For Your Safety Read Before LightingOperating Heater To Turn OFF GAS To Appliance Manual Lighting ProcedureThermostat Models For Your Safety Read Before Lighting To Select Heating LevelControl Knob CRP16T CRP26T Ignitor Button Control KnobBurner Flame Pattern Inspecting HeaterThermostat Operation Pilot Flame PatternTechnical Service Cleaning MaintenanceService Hints Observed Problem Possible Cause Remedy TroubleshootingODS/pilot lights but flame Gas leak. See Warning CRN18, CRN18T CRN30, CRN30T CRT30NT SpecificationsService Publications AccessoriesReplacement Parts Cabinet Body Models Illustrated Parts BreakdownParts List Cabinet Body Models CRT26PT and CRT30NT KEY Part Number CRT26PT CRT30NT Description QTY Burner Assembly Models CRP16, CRN18, CRP26 and CRN30 110803-02 Illustrated Parts Breakdown Parts Central Limited Warranty VENT-FREE Infrared GAS Heaters Warranty InformationKeep this Warranty

CRN30 specifications

Desa CRN30 is an innovative and versatile product designed to meet the growing demands of modern users seeking efficiency and reliability in their daily tasks. This advanced device, characterized by its cutting-edge features and robust technology, stands out in the market for both personal and professional use.

One of the main features of the Desa CRN30 is its powerful processing unit, which is engineered to handle multitasking with ease. Equipped with a high-performance chipset, it ensures smooth operation across various applications, making it ideal for users who demand speed and efficiency. The device also boasts ample memory and storage options, allowing users to seamlessly manage large files and run multiple applications simultaneously without any lag.

In terms of connectivity, the Desa CRN30 offers a range of options, including Bluetooth, Wi-Fi, and USB connections, ensuring that users can easily connect to a variety of devices and networks. This seamless connectivity allows for effortless data transfer and communication, enhancing productivity for both personal and professional tasks.

The durability of the Desa CRN30 is another significant characteristic. Constructed with high-quality materials, the device is designed to withstand rigorous use while maintaining a sleek and sophisticated appearance. Its lightweight design adds to its portability, making it easy for users to carry it wherever they go, whether to meetings, on commutes, or while traveling.

User experience is enhanced through an intuitive interface that provides easy navigation. The device features a vibrant display that ensures clear visibility in various lighting conditions, further elevating the user experience. Additionally, the Desa CRN30 is compatible with a range of applications, providing users with the flexibility to customize their device according to their specific needs.

Security is also a prime consideration in the design of the Desa CRN30. With advanced security features such as biometric authentication and encrypted storage, users can rest assured that their data and personal information are well-protected from unauthorized access.

In conclusion, the Desa CRN30 stands out as a powerful, reliable, and secure device that caters to the needs of modern users. Its exceptional features, advanced technology, and user-friendly design make it an ideal choice for anyone looking to enhance their productivity and experience in an increasingly digital world. Whether for work or leisure, the Desa CRN30 promises to deliver outstanding results.
Top Page Image Contents