Desa CRN30 Check GAS Type, Installation Items, Locating Heater, Ventilation Air From Outdoors

Page 7

AIR FOR COMBUSTION

AND VENTILATION

Continued

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills or ducts. You must provide two permanent openings: one within 12” of the ceiling and one within 12” of the floor. Connect these items directly to the outdoors or spaces open to the outdoors. These spaces include attics and crawl spaces. Follow the National Fuel Gas Code, ANSI Z223.1/NFPA 54, Section 5.3, Air for Combustion and Ventilation for required size of ventilation grills or ducts.

IMPORTANT: Do not provide openings for inlet or outlet air into attic if attic has a thermostat- controlled power vent. Heated air entering the attic will activate the power vent.

 

Outlet

Ventilated

 

Attic

 

Air

 

 

Outlet

 

 

Air

 

To Attic

 

 

 

 

To

 

 

Crawl

Inlet

 

Space

 

 

Air

 

 

 

Inlet Air

Ventilated

 

Crawl Space

 

 

Figure 3 - Ventilation Air from Outdoors

INSTALLATION

NOTICE: This heater is intended for use as supplemental heat. Use this heater along with your primary heating system. Do not install this heater as your pri- mary heat source. If you have a central heating system, you may run system’s circulating blower while using heater. This will help circulate the heat throughout the house. In the event of a power outage, you can use this heater as your primary heat source.

WARNING: A qualified ser- vice person must install heater. Follow all local codes.

CHECK GAS TYPE

Use only the correct type of gas (natural or pro- pane/LP). If your gas supply is not the correct gas type, do not install heater. Call dealer where you bought heater for proper type heater.

WARNING: This appliance is equipped for (natural or pro- pane/LP) gas. Field conversion is not permitted.

INSTALLATION ITEMS

Before installing heater, make sure you have the items listed below.

•for propane/LP gas, external regulator (supplied by installer)

•piping (check local codes)

•sealant (resistant to propane/LP gas)

•equipment shutoff valve *

•ground joint union

•sediment trap

•tee joint

•pipe wrench

•for natural gas, test gauge connection*

*A CSA design-certified equipment shutoff valve with 1/8" NPT tap is an acceptable alternative to test gauge connection. The optional CSA design- certified equipment shutoff valve can be purchased from your dealer. See Accessories, page 23.

LOCATING HEATER

WARNING: Maintain the minimum clearances shown in Figure 4. If you can, provide greater clearances from floor, ceiling and joining wall.

CEILING

36"

10"Minimum Minimum

From Sides Of Heater

Left

Right

Side

Side

2" Minimum To

Top Surface

FLOOROf Carpeting,

Tile Or Other

Combustible

Material

Figure 4 - Mounting Clearances As

Viewed From Front of Heater

107883-01H

www.desatech.com

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Model CRN30 Shown CRP26, CRP26T, CRT26PT, CRN30, CRN30T, CRT30NTTable of Contents Safety Information Local Codes Product FeaturesUnpacking Providing Adequate Ventilation AIR for Combustion VentilationDetermining FRESH-AIR Flow for Heater Location Ventilation Air From Inside Building Ventilation AIRLocating Heater InstallationInstallation Items Check GAS TypeMounting Bracket Installing Heater to WallThermostat Sensing Bulb Thermostat Models OnlyAttaching To Wall Anchor Method Methods For Attaching Mounting Bracket To WallMarking Screw Locations Plaque HeaterPlacing Heater On Mounting Bracket Installing Bottom Mounting ScrewsMounting Base Feet to Heater Connecting to GAS SupplyMounting Base Feet to Floor Where required by local code Mounting Heater to FloorJoint Nipple Sediment Trap From External Regulator Checking GAS ConnectionsTest Pressures Equal To or Less Than 1/2 Psig 3.5 kPa Test Pressures In Excess Of 1/2 Psig 3.5 kPaOperating Heater NON-THERMOSTAT Models For Your Safety Read Before LightingLighting Instructions To Turn OFF GAS To Appliance Manual Lighting ProcedureThermostat Models For Your Safety Read Before Lighting To Select Heating LevelControl Knob CRP16T CRP26T Ignitor Button Control KnobBurner Flame Pattern Inspecting HeaterThermostat Operation Pilot Flame PatternService Hints Cleaning MaintenanceTechnical Service Observed Problem Possible Cause Remedy TroubleshootingODS/pilot lights but flame Gas leak. See Warning CRN18, CRN18T CRN30, CRN30T CRT30NT SpecificationsReplacement Parts AccessoriesService Publications Cabinet Body Models Illustrated Parts BreakdownParts List Cabinet Body Models CRT26PT and CRT30NT KEY Part Number CRT26PT CRT30NT Description QTY Burner Assembly Models CRP16, CRN18, CRP26 and CRN30 110803-02 Illustrated Parts Breakdown Parts Central Keep this Warranty Warranty InformationLimited Warranty VENT-FREE Infrared GAS Heaters

CRN30 specifications

Desa CRN30 is an innovative and versatile product designed to meet the growing demands of modern users seeking efficiency and reliability in their daily tasks. This advanced device, characterized by its cutting-edge features and robust technology, stands out in the market for both personal and professional use.

One of the main features of the Desa CRN30 is its powerful processing unit, which is engineered to handle multitasking with ease. Equipped with a high-performance chipset, it ensures smooth operation across various applications, making it ideal for users who demand speed and efficiency. The device also boasts ample memory and storage options, allowing users to seamlessly manage large files and run multiple applications simultaneously without any lag.

In terms of connectivity, the Desa CRN30 offers a range of options, including Bluetooth, Wi-Fi, and USB connections, ensuring that users can easily connect to a variety of devices and networks. This seamless connectivity allows for effortless data transfer and communication, enhancing productivity for both personal and professional tasks.

The durability of the Desa CRN30 is another significant characteristic. Constructed with high-quality materials, the device is designed to withstand rigorous use while maintaining a sleek and sophisticated appearance. Its lightweight design adds to its portability, making it easy for users to carry it wherever they go, whether to meetings, on commutes, or while traveling.

User experience is enhanced through an intuitive interface that provides easy navigation. The device features a vibrant display that ensures clear visibility in various lighting conditions, further elevating the user experience. Additionally, the Desa CRN30 is compatible with a range of applications, providing users with the flexibility to customize their device according to their specific needs.

Security is also a prime consideration in the design of the Desa CRN30. With advanced security features such as biometric authentication and encrypted storage, users can rest assured that their data and personal information are well-protected from unauthorized access.

In conclusion, the Desa CRN30 stands out as a powerful, reliable, and secure device that caters to the needs of modern users. Its exceptional features, advanced technology, and user-friendly design make it an ideal choice for anyone looking to enhance their productivity and experience in an increasingly digital world. Whether for work or leisure, the Desa CRN30 promises to deliver outstanding results.
Top Page Image Contents