FMI FVF30PW, FVF24PW, FVF18PW Minimum Noncombustible Material Clearances, If Using Mantel

Page 8

FIREPLACE MANUFACTURERS INCORPORATED

UNVENTED PROPANE/LP GAS LOG HEATER

INSTALLATION

Continued

NOTICE: Manual control heaters may be used as a vented product. If so, you must always run heater with chimney flue damper open. If running heater with damper open, noncombustible material above fireplace opening is needed. Go to Installing Damper Clamp Accessory for Vented

If Using Mantel

You must have noncombustible material(s) above the fireplace opening. Noncombus- tible materials (such as slate, marble, tile, etc.) must be at least 1/2 inch thick. With sheet metal, you must have noncombustible material behind it. Noncombustible mate- rial must extend at least 8 inches up (for all models). If noncombustible material is less than 12", you must install the fireplace hood accessory (24" and 30" models only). Even

if noncombustible material is more than 12", you may need the hood accessory to deflect heat away from your mantel shelf. See Figure 5, and Figures 6 and 7, page 9, for minimum clearances.

IMPORTANT: If you cannot meet these minimum clearances, you must operate heater with chimney flue damper open. Go to Installing Damper Clamp Accessory for Vented Operation, page 10.

Operation, page 10.

Minimum Noncombustible Material Clearances

If Not Using Mantel

Note: If using a mantel, proceed to If Using Mantel. If not using a mantel, follow the information below.

You must have noncombustible material(s) above the fireplace opening. Noncombus- tible materials (such as slate, marble, tile, etc.) must be at least 1/2 inch thick. With sheet metal, you must have noncombustible material behind it. Noncombustible material must extend at least 8" up (for all models). If noncombustible material is less than 12", you must install the fireplace hood accessory (24" and 30" models only). See Figure 5 to the right for minimum clearances.

IMPORTANT: If you cannot meet these minimum clearances, you must operate heater with chimney flue damper open. Go to Installing Damper Clamp Accessory for Vented Operation, page 10.

Noncombustible

Requirements for

Material Distance (A)

Safe Installation

 

 

12" or more

Noncombustible material OK.

Between 8" and 12"

24", or 30" Models: Install fireplace hood accessory

 

 

 

 

 

(GA6050, GA6052, or GA6053, see Accessories,

 

 

 

 

 

page 21).

 

 

 

 

 

18" Model: Noncombustible material OK.

Less than 8"

Noncombustible material must be extended to at

 

 

 

 

 

least 8". See Between 8" and 12", above. If you

 

 

 

 

 

cannot extend material, you must operate heater

 

 

 

 

 

with flue damper open.

 

 

 

 

 

 

 

Heat Resistant

 

 

 

 

 

 

 

 

 

 

 

Material

 

 

 

 

 

 

 

 

(A)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 5 - Heat Resistant Material (Slate, Marble, Tile, etc.) Above Fireplace

8

105194

Image 8
Contents What to do if YOU Smell GAS Save this manual for future referenceSafety Information Product Features Remote Control AccessoriesLocal Codes UnpackingAIR for Combustion and Ventilation Providing Adequate VentilationUnusually Tight Construction Confined and Unconfined SpaceDetermining if You Have a Confined or Unconfined Space AIR for Combustion VentilationDetermining FRESH-AIR Flow for Heater Location Ventilation Air From Outdoors Ventilation AIRVentilation Air From Inside Building Installation Check GAS TypeMinimum Fireplace Clearance to Combustible Materials LOG Sizing RequirementsIf Using Mantel Minimum Noncombustible Material ClearancesDetermining Minimum Mantel Clearance When using a Hood Mantel ClearancesFloor Clearances Determining Minimum Mantel ClearanceInstalling Damper Clamp Accessory for Vented Operation Installing Heater Base AssemblyInstallation Items Needed Area of Various Standard Round FluesConnecting to GAS Supply Attaching Base Assembly to Fireplace FloorChecking GAS Connections Pressure Testing Gas Supply Piping SystemPressure Testing Heater Gas Connections Installing GWMS2 Optional Wall Mounted Switch Installing LogsItems Included for Installation Connecting to Log SetLighting Instructions For Your Safety Read Before LightingOperating Heater Optional Remote Operation Manual Lighting ProcedureTo Turn OFF GAS To Appliance Inspecting Burners Pilot Flame PatternBurner Primary AIR Holes Main BurnerTroubleshooting Observed Problem Possible CauseObserved Problem Possible Cause Remedy Maintenance,Gas leak. See Warning statement at Cleaning and Maintenance Replacement PartsAccessories Service HintsTechnical Service SpecificationsIllustrated Parts Breakdown Heat Majic LOG Models FVF18PW, FVF24PW, FVF30PWParts List KEY Part Number for FVF18PW FVF24PW FVF30PW Description QTYWarranty Information Limited Warranty VENT-FREE PROPANE/LP GAS LOG Heaters

FVF18PW, FVF30PW, FVF24PW specifications

The FMI FVF18PW, FVF30PW, and FVF24PW are part of a premier line of electric fireplaces, expertly designed to merge efficiency, luxury, and convenience. Each model boasts distinct features tailored to meet varying needs, making them ideal choices for homeowners seeking a stylish, modern heating solution.

The FMI FVF18PW is a compact yet powerful fireplace, providing an elegant ambiance to smaller spaces. Its sleek design is complemented by a high-efficiency heating system that allows for rapid warming. Utilizing advanced LED technology, the FVF18PW offers realistic flame effects, recreating the allure of a traditional fire without the associated hassles. This model includes several user-friendly controls, enabling you to customize the flame brightness and heat settings, ensuring both comfort and energy savings.

Moving on to the FMI FVF24PW, this model strikes a perfect balance between size and efficiency. Ideal for medium-sized rooms, the FVF24PW features an impressive heat output paired with a stunning visual display. One remarkable characteristic of this unit is its built-in thermostat, which helps maintain consistent temperatures while optimizing energy consumption. The flame effects can be modified to suit your mood, offering a range of colors and intensities, transforming your living space into a cozy retreat.

At the top of this exceptional line, the FMI FVF30PW is a robust fireplace engineered for larger areas, providing significant heat output without compromising on style. This model incorporates innovative heating technologies, including an advanced fan system that distributes warmth evenly throughout the room. The FVF30PW also features customizable flame settings, allowing users to create their desired atmosphere, whether for a relaxing evening or a festive gathering. Additionally, the unit comes with a remote control, enhancing convenience by allowing you to adjust features from anywhere in the room.

Across the FVF series, safety is a paramount concern. Each model is equipped with automatic shut-off features and overheat protection mechanisms for peace of mind. These electric fireplaces are also energy-efficient, providing warmth without the emissions associated with traditional wood-burning options.

In summary, the FMI FVF18PW, FVF30PW, and FVF24PW electric fireplaces combine state-of-the-art technology with beautiful design, bringing warmth, ambiance, and safety to your home. Whether you opt for the compact elegance of the FVF18PW, the versatile allure of the FVF24PW, or the powerful efficiency of the FVF30PW, each model offers a unique solution tailored to enhance your living space.