Bryant HUM-56-1 manual Installation of HUMBBWTR2019-A Bypass Water Saver Humidifier, Ð8Ð

Page 8

5.Attach transfer tube to solenoid valve and insert free end into inlet fitting on top of unit housing.

6.Attach bridge rectifier to solenoid valve.

7.Insert sheet metal screws into lower holes in plenum, pre-drilled using template.

8.Tighten screws until heads protrude approximately 3/16-in.

9.Hang humidifier on bottom screws and push top of humidi- fier to plenum, aligning top screw holes with flange, and insert screws.

10.Align and level unit.

11.Tighten all screws for air tight seal.

V. INSTALL BYPASS DUCT

Attach field-supplied 6-in. diameter duct, elbow, or starting collar with field-supplied 1/4-in. zip screws. Install supplied 6-in. damper in 6-in. duct connector.

IMPORTANT: On systems with central cooling, the damper should be closed during cooling season to prevent bypass air.

CAUTION: Do not support weight of bypass duct from humidifier Ð damage could result.

NOTE: Wiring must comply with National Electrical Code and any local codes or ordinances that may apply.

IX. START-UP

1.Open saddle valve to permit water flow to the solenoid.

2.Check all connections for water leaks.

3.Set thermostat to call for heat. Set humidistat for highest humidity setting making sure contacts are closed. After a few minutes of operation, check the drain connection for leaks and to see if water is flowing through humidifier.

4.Reverse thermostat and humidistat settings to insure proper shutdown.

5.Reset thermostat to normal setting. Reset humidistat to recommended setting.

X.FINAL STEPS

Attach humidifier maintenance instruction sticker to a visible location.

1.Inform homeowner of proper operation, maintenance, and humidistat setting.

a.If unit is installed during cooling season, close bypass damper, set humidistat for summer setting (OFF or lowest setting).

VI. INSTALL DRAIN LINE

1.Use 5/8-in. ID vinyl tubing (field supplied) to connect drain on bottom of humidifier housing to an open drain.

2. Use worm clamp to hold drain tubing in position over drain fitting outlet.

CAUTION: Unit may leak if drain tubing is misapplied. Do not insert tubing inside of drain fitting outlet.

3.Make sure line is free of traps due to sagging and has sufficient pitch to drain.

VII. MAKE WATER CONNECTION

If garden hose is not used for water supply:

1.Mount saddle valve on water line according to instructions supplied with valve.

2.Run 1/4-in. diameter (water line grade) tubing from saddle valve to adapter on solenoid valve and tighten compression fittings.

IMPORTANT: If water pressure is higher than normal (60 psi), use noise suppression disk included in parts bag. (Read water noise reducer note located inside package for instructions). For normal operation, saddle valve need only be opened 1 full turn to meet performance requirements.

3. Open valve and check installation for leaks.

NOTE: Saddle valve is self piercing on copper lines; 1/4-in. hole must be drilled in steel or iron pipes. Use only a grounded drill or a hand drill to avoid shock hazard. Turn off water and drain the pipe prior to drilling 1/4-in. hole.

VIII. INSTALL HUMIDISTAT AND COMPLETE WIRING

1.Mount humidistat on inside wall, or return-air duct in accordance with section INSTALLATION OF HUMIDIS- TAT on page 10.

2. Wire brown low-voltage leads to furnace control board, or

install a field-supplied step-down transformer 115vac/24vac 60Hz to power solenoid valve. (See Fig. 4.) Make sure bridge rectifier is attached to coil of solenoid valve.

b. If installed during heating season, set unit for normal operation.

INSTALLATION OF HUMBBWTR2019-A--

BYPASS WATER SAVER HUMIDIFIER

Bryant's HUMBBWTR2019-A-- bypass water saver humidifier can be installed on either the supply or return plenum of a forced-air system. This unit requires an external bypass duct between the supply- and return-air ductwork.

It is recommended to install the humidifier where it can be easily serviced. If this humidifier is installed with a central cooling system the factory-supplied 6-in. shutoff damper must be installed to close during the cooling season to prevent bypass air. Always install humidifier downstream of an electronic air cleaner.

I. INSPECT PACKAGE AND CHECK EQUIPMENT

Inspect contents of packaged humidifier. File claim with shipping company prior to installation if shipment is damaged or incom- plete.

The package should contain:

1.Humidifier and media assembly

2.Humidistat

3.Template

4.Ten ft 1/4-in. water supply tubing

5.Owner's Manual

6.Warranty Certificate

7.Support Bracket

8.One 1/4-in. blunt point screw

9.Saddle valve assembly

10.Four sheet metal screws

11.6-in. damper

12.Worm clamp for field-supplied drain tube

13.Humidifier maintenance instruction sticker

14.Bryant logo label

Ð8Ð

Image 8
Contents Ð1Ð Safety ConsiderationsInstallation of HUMBBLBP2018-A Bypass Humidifier → V. Install Bypass Duct → I. Inspect Package and Check EquipmentII. Select Location see FIG III. Prepare Plenum Opening see FIGVI. Install Drain Line VIII. Install Humidistat and Complete WiringInstallation of HUMBBLFP1025-A FAN Powered Humidifier VII. Make Water Connection→ V. Install Drain Line VII. Install Humidistat and Complete WiringVI. Make Water Connection VIII. START-UPInstallation of HUMBBSFP1016-A FAN Powered Humidifier Ð5ÐInstall Drain Line IV. Mount the HumidifierVI. Mount Solenoid Valve Ð6ÐÐ7Ð Installation of HUMBBSBP2017-A Bypass HumidifierIV. Mount Humidifier Installation of HUMBBWTR2019-A Bypass Water Saver Humidifier Ð8Ð→ ÐInstallation of HUMBBWTR2019-A-- Water Saver Humidifier Ð9ÐInstallation of Humidistat Wall Mounting LOW VoltageII. Duct Mounting LOW Voltage III. WiringIV. Adjustment VI. Checkout Recommended Humidistat SettingOperation

HUM-56-1 specifications

The Bryant HUM-56-1 is a cutting-edge heating, ventilation, and air conditioning (HVAC) unit that has garnered attention in both residential and commercial sectors for its advanced features and efficient performance. Designed to provide optimal climate control, the HUM-56-1 incorporates several innovative technologies that set it apart from traditional HVAC systems.

One of the standout features of the Bryant HUM-56-1 is its high-efficiency design. The unit boasts an impressive Seasonal Energy Efficiency Ratio (SEER) rating, which indicates its ability to deliver maximum cooling with minimal energy consumption. This efficiency translates into lower utility bills and a reduced carbon footprint, making it an environmentally conscious choice for homeowners and businesses alike.

The HUM-56-1 employs advanced smart technology, including Wi-Fi connectivity and compatibility with smart home systems. This allows users to monitor and control their HVAC system remotely via mobile devices, providing convenience and flexibility. The unit also features programmable settings that enable users to customize their indoor climate according to their schedules, further enhancing energy savings and comfort.

Another key characteristic of the HUM-56-1 is its quiet operation. Equipped with sound-dampening features, the unit minimizes noise levels, ensuring a peaceful indoor environment. This is particularly beneficial for residential applications where noise disruption can impact daily life.

In terms of air quality management, the HUM-56-1 is designed to optimize indoor air quality. The unit is compatible with advanced filtration systems that remove allergens and pollutants from the air, making it an excellent choice for allergy sufferers. Additionally, the system’s ventilation capabilities ensure fresh air circulation, promoting a healthier living space.

Durability is a crucial aspect of the Bryant HUM-56-1. Constructed with high-quality materials, the unit is built to withstand various environmental conditions, ensuring longevity and reliable performance. Bryant also backs the HUM-56-1 with a comprehensive warranty, highlighting their commitment to quality and customer satisfaction.

Overall, the Bryant HUM-56-1 stands out in the HVAC market due to its efficiency, smart technology integration, quiet operation, enhanced air quality features, and durable construction. These characteristics make it a preferred choice for those seeking a reliable and effective climate control solution. Whether for residential or commercial use, the HUM-56-1 is poised to deliver outstanding performance and comfort all year round.