Using the Silence Feature

Note any combustion equipment not inspected by the technician, and consult the manufacturers’ instructions, or contact the manufacturers directly, for more information about CO safety and this equipment. Make sure that motor vehicles are not, and have not, been operating in an attached garage or adjacent to the residence. Write down the number of a qualiﬁed appliance technician here:

_______________________________________

WARNING!

NEVER disconnect the power to your CO alarm to silence the horn—use the silence feature. Disconnecting the CO alarm removes your protection! See previous page for details on responding to an alarm.

The silence feature is intended to temporarily silence your CO alarm’s alarm horn while you correct the problem—it will not correct a CO problem. While the alarm is silenced, it will continue to monitor the air for CO.

When CO reaches the “Alarm” level, it will sound— repeating horn pattern: 4 beeps, a pause, 4 beeps, etc. Press and hold the Test/ Silence button until the horn is silent. The initial Silence cycle will last approximately 4 minutes.

To silence an interconnected series of alarms, you must press the Test/Silence button on the initiating alarm (the unit with the ﬂashing red

light). If you press the Test/Silence on any other alarm, it will only silence that unit, not the whole interconnected series.

NOTE:

After initial 4-minute silence cycle, the

CO alarm re-evaluates present CO levels and responds accordingly. If CO levels remain potentially dangerous—or start rising higher— the horn will start sounding again.

While the detector is silenced:

If the CO alarm... is silent for only

4 minutes, then starts sounding loudly—

4 beeps, then a pause, 4 beeps, then a pause. Red light (LED) continues ﬂashing...

This means... CO levels are still potentially dangerous.

If the CO alarm...remains silent....

This means...unit has returned to normal operation.

Finding the Source of CO

After an Alarm

Because CO may dissipate by the time an investigator arrives, it may be difﬁcult to locate the source of CO. See Chapter 5 “What You Must Know About CO.” BRK Brands, Inc. shall not be obligated to pay for any carbon monoxide investigation or service call.

CO5120B specifications

The BRK electronic CO5120B is a state-of-the-art carbon monoxide detector that serves as an essential safety device for households and commercial spaces. Designed with advanced technologies and features, the CO5120B ensures reliable detection of carbon monoxide, a colorless and odorless gas that can be extremely harmful or even fatal.

One of the standout features of the CO5120B is its electrochemical sensor, which is both sensitive and accurate in detecting low levels of carbon monoxide. This technology not only enhances the unit's reliability but also ensures a quicker response time in the event of a CO leak. The detector has a measurement range of 30 to 999 parts per million (PPM), allowing it to monitor a wide range of potential threat levels.

The CO5120B also comes equipped with a digital display that shows real-time CO levels, providing users with instant information about the air quality in their environment. This feature is particularly beneficial as it enables users to assess potential risks immediately and take necessary actions before escalating issues occur. The display also features a peak level memory that records the highest level of carbon monoxide detected since the last reset, aiding in diagnosing potential problems over time.

Battery backup is another critical characteristic of the CO5120B. With a 9V battery backup option, the unit continues to provide protection even during power outages, ensuring that families and occupants remain safe under any circumstances. Meanwhile, an end-of-life signal alerts users when it's time to replace the detector, ensuring long-term effective monitoring.

The CO5120B is designed with a low-profile, sleek look, allowing it to blend seamlessly into any home decor. Its simple installation process requires minimal tools, making it accessible for DIY enthusiasts and everyday users alike. The device is also equipped with an easy-to-access test/reset button, allowing users to routinely check the functionality of the unit.

Overall, the BRK electronic CO5120B is a reliable and efficient carbon monoxide detector that prioritizes safety and user-friendliness. Its combination of cutting-edge sensor technology, real-time monitoring, battery backup, and added convenience features makes it an excellent choice for anyone looking to enhance their safety against this silent threat in the home or workplace.